Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Class Of Service2-63
Chapter 2 - Features and Operation
6. Enter a valid number on the dial pad (1-7) corresponding to one of seven possible Classes 
of Service to which a station may be assigned.
The seven Classes of Service are:
[1] = COS 1; No restrictions.
[2] = COS 2; Table A governs
[3] = COS 3; Table B governs
[4] = COS 4; Table A and B govern
[5] = COS 5; Restricts [0], [1], [

], [#] dialed as first-digit and places a 7-digit maximum.
[6] = COS 6; Intercom Only (no CO line access - results in a...

2-64CO Flexible Port Assignment
Chapter 2 - Features and Operation
CO Flexible Port Assignment
Description
The Flexible Port Assignment feature provides a means to assign CO line numbers to any CO 
line port in the system. This provides complete flexibility in determining CO line numbers 
within the system as long as they stay within the system numbering plan. A CO line can be 
assigned any number between 001and the maximum number of CO lines in your system.
The buttons on the digital telephone are...

CO Flexible Port Assignment2-65
Chapter 2 - Features and Operation
Programming Steps
If the CO Line numbers need to be relocated to different ports, press FLASH and dial [42]. 
The following message displays:
Buttons 1 through 18 indicate Ports 1 through 144. When the relocation program is initially 
entered, Button #1 is lit to indicate that the user is programming the CO Line numbers.
To change the CO Line number assigned to any port:
1. Dial the position number on the display (01 through 08).
2. Then...

2-66CO Line - Access
Chapter 2 - Features and Operation
CO Line - Access
Description
Through programming, telephones are allowed or denied access to particular outside lines or 
line groups. Refer to “Line Group Access - Station” on page 2-72, “Flexible Button” on page 2-149, 
and “CO Line Group Programming” on page 2-74.
Operation
To access an outside line:
1. Press idle CO line button, POOL button,
-or-
Dial CO line group access code or LCR code: 9, 801-823, 88+LLL (LLL = CO Line number).
2. Dial...

CO Line Attributes2-67
Chapter 2 - Features and Operation
CO Line Attributes
Initialize CO Line Attributes
Description
CO Line parameters may be initialized to set all data fields to their original, default values. The 
following data fields are returned to their default value upon initializing the CO Line 
Attributes.
Table 2-4: CO Line Attribute Defaults
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
FLASH 40
PA G E  A1 DTMF/Dial Pulse Programming DTMF
2 CO/PBX Programming CO...

2-68CO Line Attributes
Chapter 2 - Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 80, Button #2). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
FLASH 40
PA G E  C1 Flash Timer Programming 10=1.0 sec
2 Ring Delay Timer 00=Disabled
3 Wink Timer 140 ms
4 Release Timer 020=200 ms
5 Reseize Timer 200=200 ms
6Guard Timer 05=.5 sec
7 Seize Timer 010=0.1 sec
8Preset Forward Timer 10 sec
9 DID Collect Timer 015=150 ms
10 T-1...

CO Line Attributes2-69
Chapter 2 - Features and Operation
Print CO Line Attributes
Description
The Print CO Line Attributes command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database The system baud rate must match that of the 
printer or receiving device.
When printing the CO Line attributes the following data prints:

All CO Line parameters within the specified range.

CO Line ringing assignments within the specified range.

Dial Pulse Ratio and Speed...

2-70CO Line DTMF Sending
Chapter 2 - Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 85, Button #2). The following 
message displays:
2. To print data for:

ALL CO Lines, press the HOLD button.

A specified CO Line Range, enter 6 digits ( 3 digits for the first line and 3 digits for the 
last line in the range):

One CO Line, enter that line twice: [001001]
3. Then press the HOLD button. The following message displays and the CO Line data prints:
When the...

CO Line DTMF Sending2-71
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range 
4. Press the DTMF/DIAL PULSE flexible button (FLASH 40, Page A, Button #1).
5. Enter a 0 or 1 that corresponds with the following entries:
[0] = Dial Pulse
[1] = DTMF
6. Press HOLD to save the entry. A...

2-72CO Line Group
Chapter 2 - Features and Operation
CO Line Group
Description
Outside lines can be placed in one of twenty-four groups if the customers business requires 
such grouping. Stations are then individually assigned access to these groups and given the 
ability to dial on particular lines.
Line Group Access - Station
Description
A station can access any combination of outside line groups, or a station may not be allowed 
access to outside lines. CO line groups are used primarily by single line...