Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Direct Inward Dialing2-113
Chapter 2 - Features and Operation
DID/ICLID Ringing Assignments
Description
ICLID Ringing Assignments let you change the ring assignment based on the incoming 
number received. This feature permits you to select from 500 ringing routes for each entry in 
the name to number translation table and DID table (Flash 55). For example, this feature 
could be used to reroute selected customers to a specific ACD or UCD group and bypass the 
general Attendant.
The Direct Inward Dialing...

2-114Direct Inward Dialing
Chapter 2 - Features and Operation
3. Enter a valid Destination (DDD) or (DDDD) and Ring type (R) followed by HOLD. A 
confirmation tone sounds and the display updates.
* Internal flexible numbers range = 100-8999
** Remote device numbers can be any numbers between 1000-8999, excluding those numbers assigned for internal use.
a For Remote Voice Mail Ring Assignment, refer to Flash 67.
View DID/ICLID Ringing Assignments
Description
Keysets designated to ring on an incoming CO...

Direct Inward Dialing2-115
Chapter 2 - Features and Operation
XDDDD = Destination type ID letter fllowed by number to be dialed:
     [F]] plus Fixed Number, e.g., F102
     [H] plus Hunt Group Number, e.g., H6700
     [M] plus Modem Extension Number, e.g., M6099 (default = M499N)
     [R] plus Recorded Announcement Extension Number, e.g., R6020
     [S] plus Station Number, e.g., S6002
     [U] plus UCD/ACD Group/Agent Number, e.g., U6034
     [V] plus Voice Mail Group Number, e.g., V6899
     [B] plus...

2-116Direct Inward Dialing
Chapter 2 - Features and Operation
DID Digits
Description
The DID Digits option allows the installer to adjust the amount of DID Digits received from 
the CO. This amount is used by all DID trunks in the system.
The DID Translation table can be programmed to determine the number of digits used for 
the routing of a DID call.
Programming Steps
To change the number of DID Digits:
1. Press the DID DIGITS flexible button (FLASH 41, Button #3). The following message is 
shown on the...

Direct Inward Dialing2-117
Chapter 2 - Features and Operation
3. Press the HOLD button to save the entry. A confirmation tone sounds and the display 
updates.
DEFAULT … DID Incoming Signaling type is set for DTMF.
DID/TIE Signaling
Description
The DID/TIE Signaling feature can be programmed for one-way direct access inward dialing 
access to specific stations on specific DID lines without going through an Attendant 
answering position.
Programming Steps
1. Press FLASH and dial [40]. The following message...

2-118Direct Inward Dialing
Chapter 2 - Features and Operation
DID Collect Timer
Description
The DID Collect Timer is only used when the DID Incoming Signaling is set for dial pulse. This 
is a time-out timer that looks at the incoming digits one digit at a time. If a second digit isn’t 
detected within the 150ms, the telephone system attempts to process that digit. If a second 
digit is detected, the system waits 150ms to see if a third digit is received. Otherwise, the 
telephone system attempts to...

Direct Inward Dialing2-119
Chapter 2 - Features and Operation
Initialize DID-TIE Parameters
Description
The DID-TIE Parameters and Timers may be initialized, setting all data fields to their original 
default values.
Programming Steps
1. Press the DID-TIE PARAMETERS flexible button (FLASH 80, Button #13). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
Print DID-TIE Parameters
Description
The Print DID-TIE command dumps the entire database as a permanent record...

2-120 D ire c t In w a rd  Syste m Ac c ess  (D IS A )
Chapter 2 - Features and Operation
Programming Steps
1. Press the DID-TIE PARAMETERS flexible button (FLASH 85, Button #14). The following 
message displays:
2. To print the DID-TIE Parameters, press the HOLD button. The following message displays:
When the system has finished sending the requested information to the printer, 
confirmation tone sounds.
Direct Inward System Access (DISA)
The XTS allows programming of an unlimited number of outside...

Direct Inward System Access (DISA) 2-121
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … 100 is the assigned access code.
DISA Programming
Description
Each CO can be assigned as a DISA line using 1 of the 5 DISA types available.

DISA can be programmed using Range programming.

DISA callers are subject to the Class of Service placed on the line accessed for out dialing.

The system administrator can control the call...

2-122 D ire c t In w a rd  Syste m Ac c ess  (D IS A )
Chapter 2 - Features and Operation
5. Enter a valid number (0-5) on the dial pad to indicate type of DISA desired.
[0] = No DISA
[1] = 24-Hour DISA
[2] = Night DISA
[3] = 24-Hour DISA with forwarding
[4] = Night DISA with forwarding
[5] = Telecenter 24-Hour DISA with forwarding (requires optional software)
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … No outside lines are assigned as DISA lines.
DISA...