Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Direct Inward System Access (DISA) 2-123
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of...

2-124 D ire ct  Sta tio n Sel ec ti o n  / B usy L a m p Fie ld
Chapter 2 - Features and Operation
To reach an internal station:
Dial the desired station number. (Ringback tone sounds.)
Direct Station Selection / Busy Lamp Field
A user with Direct Station Selection (DSS) buttons assigned at their Key Station can call an 
intercom station or transfer a CO call by pressing the appropriate DSS button.
When a button on a Digital Telephone is assigned as a DSS, it also serves as a Busy Lamp Field 
(BLF) to...

Directory Dial2-125
Chapter 2 - Features and Operation
Directory Dial
Description
Directory Dial enables display telephone station users to obtain a directory of station users 
and have the system dial the extension currently displayed. The XTS provides locations for up 
to 200 names (000-199). Directory dial also lets users program a name with a speed dial bin 
for use in later locating a speed dial number. When prompted, the system displays the name 
associated with a speed dial number so when the...

2-126Directory Dial
Chapter 2 - Features and Operation
Programming Steps
To enter, change, erase or view entries in the Directory Dial List:
Press FLASH and dial [23].The following message displays
AAA = Directory list entry number (000-199)
XXXX = Either:
A 3-digit station number (100-351)
-or-
A 3-digit local number/name translation table number (600-799)
-or-
A 4-digit remote device number (1000-8999)
-or-
A 4-digit system speed bin number (9020-9999)
nnn = programmed name (blank if none)
To select a...

Directory Dial2-127
Chapter 2 - Features and Operation
3. If an error is made while entering the name, press the BACK SPACE flexible button 
(FLASH 23, Button #4). This button backspaces one character at a time.
Figure 2-8: Directory List Keypad Map
4. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Name – A name up to 24 characters may be entered into each directory dial list entry. The 
names display alphabetically when accessed by a station user. It is possible to...

2-128Directory Dial
Chapter 2 - Features and Operation
Pressing 2 a third time displays names that start with C). The alphabet is represented on 
the keypad as shown below.
Figure 2-9: Directory Dialing Keypad Map
Names beginning with the letter chosen display on the LCD display.
3. Dial [

] to scroll up (next entry) through the list,
-or-
Dial [#] to scroll down (previous entry) through the list,
-or-
Press another key to view the list for a different letter of the alphabet.
4. When the desired name...

Directory Dial2-129
Chapter 2 - Features and Operation
Conditions
» If the desired party is an intercom station, that station is signaled according to their 
intercom selector/H-T-P switch (SLT stations tone ring).
» If the desired party is associated to a speed dial bin, the system selects a CO line and dials 
the number programmed into the speed dial bin. Call progress tones are then heard.
» If station is in Directory Dial mode and a CO or intercom call rings in, the station must exit 
Directory Dial...

2-130Directory Dial
Chapter 2 - Features and Operation
Print Directory Dial Table Parameters
Description
The Print Directory Dial Table command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
This is an example of the Directory Dial Table database printout.
LST
---
000
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029...

Directory Dial2-131
Chapter 2 - Features and Operation
Programming Steps
1. Press the DIRECTORY DIAL TABLE flexible button (FLASH 85, Button #10). The following 
message displays:
2. To print the Directory Dialing Table parameters, press the HOLD button. The following 
message displays:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Dial-By-Name
Description
The system allows station users to dial extension numbers, or speed bins, by entering the...

2-132Distinctive Ringing
Chapter 2 - Features and Operation
EXAMPLE -- To search for the name BROWN, press [2][7][6][9][6].

When the system finds a unique numeric match to the name being dialed, the call is 
placed to the station matching the name.

The intercom call signals the station according to the H-T-P button.

If fewer than 8 digits are dialed, the numeric match is dialed after a 10-second 
interdigit time-out occurs, or if [#] is pressed.
Conditions
» The system dials the station that matches...