Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

So f tw a re Id en t ific a ti o n  ( MP B ) 2-253
Chapter 2 - Features and Operation
The SLT Hook Flash Bounce Timer setting is variable from 0-1 seconds in 10 ms increments. 
This is a 3-digit entry where 010 equals 0.1 seconds.
Figure 2-17: Hook Switch Activity
Programming Steps
1. Press the SLT HOOK FLASH BOUNCE TIMER flexible button (FLASH 01, Button #15). The 
following message displays:
2. Enter a valid number on the dial pad that corresponds to 0-1 seconds in 10 ms 
increments.
3. Press HOLD to...

2-254Software Version (MPB)
Chapter 2 - Features and Operation
Software Version (MPB)
Description
The current system software version can be viewed. The display shows the version number 
and level of software.
Operation
To view the Software Version Display:
Dial the S/W Display code [605] on the dial pad. The top line of the LCD shows the 
engineering version of the software. The bottom line of the LCD shows the features that 
are enabled for your software, e.g., BASIC or ACD.
Conditions
» The station...

Speakerphone2-255
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current...

2-256Sp ee d Di al
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Speakerphone Operation
Description
The Speakerphone feature allows you to conduct a conversation without lifting the handset. 
Speakerphone volume can be adjusted as desired.
Operation
1. Press...

Speed Dial2-257
Chapter 2 - Features and Operation
2. Press the SPEED button and dial speed bin location,
-or-
Press the preprogrammed speed bin button.
To store speed dial numbers:
1. Press the SPEED button once.
2. Press an OUTSIDE LINE button or POOL button.
-or-
Select an outside line by pressing the SPEED button again.
3. Dial the speed bin location.
4. Dial the desired telephone number and include these special codes:

TRANS -- Initiates a Pulse-To-Tone switchover.

HOLD -- Inserts a Pause.

FLASH...

2-258Sp ee d Di al
Chapter 2 - Features and Operation
To store speed dial numbers:
1. Lift handset.
2. Dial [661] on the dial pad.
3. Dial desired station speed number (9000-9019).
4. Dial telephone number to store.
5. Briefly press and release the hookswitch. A confirmation tone sounds.
System Speed Dial Access
Description
Stations can be individually allowed or denied the ability to use system speed dial 
(9020-9999) numbers. (System speed numbers 9060-9099 are not monitored by toll restriction.)...

Speed Dial2-259
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the SPEED flexible button (Button #6). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … System Speed Dialing is enabled at...

2-260Sp ee d Di al
Chapter 2 - Features and Operation
System Speed Bin Access
Description
The System Speed Bin Access feature has 900 entries available. A station can be allowed or 
denied access to bins 9100-9999. Access to system speed bins 9020-9099 can not be 
restricted. Stations are granted the ability to dial all Speed Dial Numbers within the specified 
range.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to...

Speed Dial2-261
Chapter 2 - Features and Operation
4. Press button #21. The display updates to reflect current programming for Page C.
5. Press the SYS BIN RANGE button (Button #6). The following message displays:
6. Enter a range of speed bins to be allowed (100-999). The leading digit 9 is not reflected on 
the LCD and is not used for your entry.
7. Press HOLD to save the entry.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51...

2-262Sp ee d Di al
Chapter 2 - Features and Operation
Print System Speed Numbers
Description
The System Speed Numbers command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
Figure 2-18: System Speed Numbers Printout
Programming Steps
1. Press the SYSTEM SPEED flexible button (FLASH 85, Button #6). The following message 
displays:
2. To print the System Speed bins, press the HOLD...