Siemens Saturn Iie Epabx General Description Manual
Have a look at the manual Siemens Saturn Iie Epabx General Description Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 428 Siemens manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SATURN IIE EPABX Maintenance and Troubleshooting Table 4.14 Attendant Console Test (Continued) STEP PROCEDURE VERIFICATION IF VERIFICATION IS NOT OBTAINED . 9 Remove and reinsert handset assem- INSERT HANDSET is displayed while bly to terminate test, or wait 30 sec- handset is removed. After handset is onds for test timeout. reinserted, console returns to normal operation. 10 If no additional Apparatus Tests are to be performed proceed as follows: Place maintenance test phone Dial tone is returned. off-hook. Dial the Diagnostic Test Access Code. Recall dial tone is returned. Dial 2 to disable the Apparatus Tests. None. Place maintenance test phone None. on-hook. Table 4.15 Attendant Console Displayable Characters ORDER 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 2 27. 28. 29. 30. 31. 32. CHARACTER ORDER CHARACTER I 1 I ! ! F ! ! -;,,,; 33. AAAAAAAA 34. BBBBBBBB 35. cccccccc f§S$$S$$$ 36. DDDDDDDD 010 % o/o o/o o/o o/o o/o % 37. EEEEEEEE &&&&&&&& 38. FFFFFFFF I I I I I I I I 39. GGGGGGGG ( ( ( ( ( ( ( ( 40. HHHHHHHH 41. I I I I I I I I ))I))))) t * * * * l l * 42. JJJJJJJJ ++++++++ 43. KKKKKKKK 9 I I , I I I I 44. LLLLLLLL - - - - - - - - 45. MMMMMMMM i i i i i i i i 46. NNNNNNNN 47. 00000000 00000000 48. PPPPPPPP 1 1 1 1 1 1 1 1 49. QQQQQQQQ 22222222 50. RRRRRRRR 33333333 51. sssssss.s 44444444 52. TTTTTTTT 55555555 53. uuuuuuuu 66666666 54. vvvvvvvv 77777777 55. wwwwwwww 88888888 56. xxxxxxxx 99999999 : : : : : : : : 58. 57. YYYYYYYY zzzzzzzz ; ; ; ; ; ; : ; (((((((( 2 1 I I [ 1 \\\\\\\ I I [ ====== KU)))) 61. 62. ~~~L~~ ???????? 63. ------__ @?@@OQ@OQ 4-39
SATURN IIE EPABX Maintenance and Troubleshooting Table 4.16 Siemens DYAD Telephone Button Test NOTES: 1. If the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under test is class-marked with TSTAPP feature, the maintenance test phone is not required to enable or disable the Ap- paratus Diagnostic routines; therefore, perform only steps 5 through 9. 2. If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under test is not class-marked with the TSTAPP feature, the maintenance test phone is required to enable or disable the Apparatus Diagnostic routines; therefore perform the entire procedure (steps 1 through 10). STEP PROCEDURE VERIFICATION IF VERIFICATION IS NOT OBTaINED 1 Place the maintenance test phone Dial tone is returned. off-hook. 2 Dial the Diagnostic Test Access Code. Recall dial tone is returned. 3 Dial 3 to enable the Apparatus Diag- Confirmation tone is returned. nostic Tests. 4 Place maintenance test phone None. on-hook. 5 Place Siemens DYAD Telephone Dial tone is returned. off-hook. 6 Dial the Siemens Digital Telephone Recall dial tone is returned. Test Access Code. The access code is momentarily dis- If reorder tone is returned, the Sie- played, then the display unit and but- mens DYAD Telephone Button Test is ton LEDs are extinguished. in use; try again later. 7 Depress the Siemens DYAD Tele- If proper verification is not obtained or phone keypad buttons as follows: 1,2, busy tone is returned at any time, 3, 4, 5, 6, 7, 8, 9, 0, * , #. either: (1) buttons were depressed out of se- quence, (2) the DYAD Telephone is defective, or (3) the SLMD circuit is faulty. Retry the test. If proper verification is not obtained or busy tone is returned again, replace the DYAD Telephone with a known good DYAD Telephone. Retry the test. (1) If proper verification is obtained replace the DYAD Telephone. (2) If proper verification is not obtainec or busy tone is returned, the SLMD cir, cuit is faulty. Replace the associatec SLMD PCB. 8 Depress the DYAD Telephone feature Button LEDs light when depressed Same as step 7. buttons in the sequence shown in and extinguish when the next button Figure 4.06 and according to the Sie- is depressed. mens DYAD Telephone model. After the last button is depressed, the following indications occur: Ringback tone is returned. All button LEDs flash. The audible alerting device sounds at intervals. TEST COMPLETE is displayed. 4-40
SATURN IIE EPABX Maintenance and Troubleshooting A30808-X5130-DllO-l-B920 Issue 1, May 1986 Table 4.16 Siemens DYAD Telephone Button Test (Continued) STEP PROCEDURE VERIFICATION IF VERIFICATION IS NOT OBTAINED 9 Place Siemens DYAD Telephone un- Siemens DYAD Telephone-returns to der test on-hook to terminate test. normal operation. 10 If no additional Apparatus Diagnostic Test routines are to be performed, pro- ceed as follows: Place maintenance test phone Dial tone is returned. off-hook. Dial the Diagnostic Test Access code. Recall dial tone is returned. Dial 2 to disable the Apparatus Diag- None. nostic Test. Place maintenance test phone None. on-hook. 4-41
SATURN IIE EPABX A30808-X5130-DllO-l-8920 Maintenance and Troubleshooting Issue 1, May 1986 ‘iit dUTTON DYAD 26 BUTTON DYAD NOTE: These buttons do not contain LEDs. SEE NOTE2 SEE NOTE2 Figure 4.06 Siemens DYAD Telephone Button Depression Sequence 4-42
SATURN IIE EPABX Maintenance and Troubleshooting A30808-X5130-DllO-l-6920 issue 1, May 1986 Table 4.17 Siemens JR-DYAD Telephone Button Test NOTES: 1. If the svstem option flaa TSTDIAG has been enabled in the data base or the Siemens Diaital Teleohone under test is class-marked with TSTAPP feature, the maintenance test phone is not required to enaTble or disable the Ap- paratus Diagnostic routines; therefore, perform steps 5 through 9. 2. If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under test is not class-marked with the TSTAPP feature, the maintenance test ohone is required to enable or disable the Apparatus Diagnostic routines; therefore perform steps 1 throuqh 10. ’ 1 STEP PROCEDURE Place the maintenance test phone off-hook. Dial the Diagnostic Test Access Code. Dial 3 to enable the Apparatus Diag- nostic Tests Place maintenance test phone on-hook. Place JR-DYAD Telephone off-hook. Dial the Siemens Digital Telephone Test Access Code. Depress the Siemens JR-DYAD Tele- phone keypad buttons as, follows: 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * . #. Depress the JR-DYAD feature buttons in the sequence shown in Figure 4.0% VERIFICATION Dial tone is returned. Recall dial tone is returned. Confirmation tone is returned. None. Dial tone is returned. Recall dial tone is returned. Button LEDs light when depressed and extinguish when the next button is depressed. After the last button is depressed, the following indications occur: Ringback tone is returned. All button LEDs flash. The audible alerting device sounds at intervals. IF VERIFICATION I$ NOT OBTAINED f reorder tone is returned, the Sie- nens JR-DYAD Telephone Button Test s in use; try again later. !f proper verification is not obtained or ousy tone is returned at any time, aither: :l) buttons were depressed out.of se- quence, :2) the JR-DYAD Telephone is defec- tive, or (3) the SLMD circuit is faulty. Retry the test. If proper verification is not obtained or busy tone is returned again, replace the JR-DYAD Telephone with a known good JR-DYAD Telephone. Retry the test. (1) If proper verification is obtained, replace the JR-DYAD Telephone. (2) If proper verification is not obtained or busy tone is returned, the SLMD cir- cuit is faulty. Replace the associated SLMD PCB. Same as step 7. 4-43
SATURN IIE EPABX Maintenance and Troubleshooting A30808-X5130-DllO-l-8920 Issue 1, May 1986 Table 4.17 Siemens JR-DYAD telephone Button Test (Continued) STEP PROCEDURE VERIFICATION IF VERIFICATION IS NOT OBTAINED 9 Place Siemens JR-DYAD Telephone Siemens JR-DYAD Telephone returns under test on-hook to terminate test. to normal operation. 10 If no additional Apparatus Diagnostic Test routines are to be performed, pro teed as follows: Place maintenance test phone Dial tone is returned. off-hook. Dial the Diagnostic Test Access code. Recall dial tone is returned. Dial 2 to disable the Apparatus Diag- None. nostic Test. Place maintenance test phone None. on-hook. 4-44
I -- SATURN IIE EPABX Maintenance and Troubleshooting A30808-X5130-DllO-l-8920 Issue 1. May 1986 NOTES: * These feature buttons are not testable. Buttons 9 through 13 do not contam LEDs. Figure 4.07 Siemens JR-DYAD Telephone Button Depression Sequence
--). SATURN IIE EPABX A30808-X5130-DllO-l-8920 Maintenance and Troubleshooting Issue 1, May 1986 Table 4.18 Siemens DYAD Telephone Display Test NOTES: 1. If the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under test is class-marked with TSTAPP feature, the maintenance test phone is not required to enable or disable the Ap paratus Diagnostic routines: therefore perform steps 5 through 9. 2. If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under test is not class-marked with the TSTAPP feature, the maintenance test phone is required to enable or disable the Apparatus Diagnostic routines; therefore perform steps 1 through 10. STEP PROCEDURE VERIFICATION IF VERIFICATION IS NOT OBTAINED 1 Place maintenance test phone Dial tone is returned. off-hook. 2 Dial the Diagnostic Test Access Code. Recall dial tone is returned. 3 Dial 3 to enable the Apparatus Diag- Confirmation tone is returned. nostic test. 4 Place maintenance test phone None on-hook. 5 Place the Siemens DYAD Telephone Dial tone is returned. under test off-hook. 6 Dial the Siemens Digital Telephone Recall dial tone is returned. The Ac- If reorder tone is returned, the Sie- Display Test Access Code. cess code is momentarily displayed, mens Digital Telephone Display Test is then the display unit clears. being used; retry later. 7 Depress any button in the Siemens Groups of sixteen of each of the dis- If proper verification is not obtained, DYAD Telephone under test to initiate playable charactew are scrolled in the either: test. sequence shown in Table 4.19. After (1) the DYAD Te!ephone is defective, or the last character (underscore) is dis- (2) the associated SLMD circuit is (Note: The display test can be sus- played, the following occurs: faulty. Retry the test. pended any time by depressing any If proper verification is not obtained, button. The test can be resumed at Ringback tone is returned. replace the DYAD Telephone with a any time in the same manner.) known good DYAD Telephone. Retry All key LEDs flash. the test. (1) If proper verification is obtained, The audible alerting device sounds at replace the DYAD Telephone. intervals. (2) If proper verification is not obtained, the SLMD circuit is faulty. Replace the TEST COMPLETE is displayed. associated SLMD PCB. 8 Place DYAD Telephone on-hook to ter- minate test or wait 30 seconds for test timeout. 9 If no additional Apparatus Diagnostic . Tests are to be performed, proceed as follows: Place maintenance test test phone Dial tone is returned. off-hook. Dial the Diagnostic Test Access Code. Recall dial tone is returned. Dial 2 to disable the Apparatus Diag- None. nostic Test. Place maintenance test phone None. on-hook.
SATURN IIE EPABX A30808-X5130-DllO-l-8920 Maintenance and Troubleshooting Issue 1, May 1986 Table 4.19 Siemens DYAD Telephone Displayable Characters ORDER CHARACTER ORDER, CHARACTER 1. ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! 33. AAAAAAAAAAAAAAAA 2. ,, r, I, I, I, I, ,, I, II ,I I, ,I I, I, n I, -34. BBBBBBBBBBBBBBBB 3. ##########I###### 35. cccccccccccccccc 4. $$$5$S$$SSSS$SSS 36. DDDDDDDDDDDDDDDD 5. %%%%%%%%%%%%%%%% 37. EEEEEEEEEEEEEEEE 6. &&&&&&&&&&&&&&&& 38. FFFFFFFFFFFFFFFF 7. 39. GGGGGGGGGGGGGGGG 8. ;;;;;;;;;;;;;;;; 40. H-HHHHHHHHHHHHHHH 9. )))))))))))))))) 41. I I II‘1 I I I I I I I I1 I I 10. **************x* 42. JJJJJJJJJJJJJJJJ 11. ++++++++++++++++ 43. KKKKKKKKKKKKKKKK 12. .**.0...*.0**0.* 44. LLLLLLLLLLLLLLLL 13. --_---__-------- 45. MMMMMMMMMMMMMMMM 14. 46. NNNNNNNNNNNNNNNN 15. ;i;iii;iii;iiii; 4% 0000000000000000 16. 0000000000000000 48. PPPPPPPPPPPPPPPP 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 1111111111111111 2222222222222222 3333333333333333 4444444444444444 5555555555555555 6666666666666666 7777777777777777 8888888888888888 9999999999999999 . * . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . ~~~~i~i~~~~iii~~ ==========zz===== 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. 63. QQQQQ-QQQQQQQQQQQ RRRRRARRRRRRRRRR ssssssssssssssss TTTTTTTTTTTTTTTT uuuuuuuuuuuuuuuu vvvvvvvvvvvvv~vvv wwwwwwwwwwwwwwww xxxxxxxxxxxxxxxx YYYYYYYYYYYYYYYY zzzzzzzzzzzzzzzz I I [ 11 1 [ 1 [ I I [ I[ [ [ \\\\\\\\\\\\\\\ 111111’1111 I1 11 II AAAAAAAAAAAAAAAA - - - - - - - - 4-47 (4-48 blank)