Siemens Saturn Iie Epabx General Description Manual

							SATURN IIE E?ABX A30808-X5130-8120-l-8928 
Installation Test Procedures issue 1, May 1986 
TEP 
1 Place maintenance test phone 
off-hook. Dial tone returned. 
2 Dial the Diagncstic Test Access Code. Recall dial tone returned. 
3 
4A Dial 1 for tone generator test. None. 
Dial 00 if all tones are to be tested and 
verify that all tones returned are un- 
dis!orted. All tones are returned in the sequence 
shown in Table 6.01 for two seconds 
each: test repeats until the main- 
tenance test phone is placed on-hook 
or hook flashed. 
4B 
Dial the individual test number shown Chosen tone returned until main- If chcsen tono is returned dictoricd. 
in Table 6.01 if a particular tone is to tenance test phone is placed on-hco!c retry test two moie times. If distortion 
be tested. or hook-flashed. continues, replace the SMXTG PCB 
5A If additional 
tE?SiS or procedures are 
to be performed, hook-flash the main- 
tenance test phone and dial the next 
code (Diagnostic Test Access Code is 
not redialed). Recall dial tone is returned. 
56 If no additional tests or procedures are 
to be performed, placa the main- 
tenance test phone on-hook. Nono.  iab:a 6.00 Tone Generator Test 
PCDCECURE VERIFICATION 
TEST 
NUMBER 
00 
01 
02 
03 
04 
05 
06 
07 
08 
09 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 
20 
21 
22 
23 
24 
25 
26 
27 IF VERIFICATION 
IS NOT OBTAINED s 
If any tone(s) is returned distortad retry 
test two mere times. If distortion con- 
tinues, replace the SMXTG PCB. Ncto 
that the first 16 tones are hardware in- 
terrupted. if continuous tones are 
returned, replace the SMXTG PCB. 
Table 6.01 Tone Generator Test Numbers 
TONE 
Circular Sequence 
DTMF-1 (697Hz + 1209Hz) 
DTMF-2 (6Q7Hz + 1336Hz) 
DTMF-3 (697Hz + 1477Hz) 
DTMF-4 (77OHz + 1209Hz) 
DTMF-5 (77OHz + 1336Hz) 
DTMF-6 (77OHz + 14i7Hz) 
DTMF-7 (852Hz + 1209Hz) 
DTMF-8 (852Hz + 1336Hz) 
DTMF-9 (852Hz + 1477H.z) 
DTMF-0 (941Hz + 133SHz) 
DTMF-’ (941Hz + 1209Hz) 
DTMF-# (941Hz + 14i7Hz) 
DTMF-A (697Hz + 1633Hz) 
DTMF-B (770Hz + 1633Hz) 
DTMF-C (852Hz + 1633Hz) 
DTMF-D (941Hz -I- 1633Hz) 
Dial Tone (35OHz + 440Hz) 
Busy Tone (480Hz +620 Hz) 
Reorder Tone (Fast Busy Tone) 
Test Tone (1004Hz @-16dEim) 
Low Tone (440Hz) 
Audible Ring (440Hz + 480Hz - uninterrupted) 
Intercept Tone (440Hz + 620Hz) 
LDN Call Identification Tone (400 Hz + 480 Hz - interrupted) 
Called Party Tone (2100 Hz - uninterrupted) 
Remote Hold Recall Identification Tone (400 Hz) 
Quiet Tone 
--_ 
G-13  
						

							I 
SATURN IIE EPABX A30808-X5130-B120-l-8928 
Installation Test Procedures Issue 1, May 1986 
STEP PROCECURE VEFHFICATION 
1 
5 
6A 
68 Table 6.02 DTMF Receiver Test 
Place maintenance test phone 
off-hook. 
Dial the Diagnostic Test Access Code. 
Dial # for DTMF receiver test. 
Dial the four-digit PEN number of the 
DTMF receiver circuit to be tested. 
Depress the maintenance test phone 
keypad’s buttons in the following se- 
quence. Test tone (1004Hz at -16dBm) 
returned. 
a) For 12-button phones: 1, 2, 3, 
4, 5, 6, 7, 8, 9, 0, *and #. 
b) For 16-button phones: A, B, C, 
D, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, * , 
and #. 
If additional tests or procedures are 
to be performed, hook-flash main- 
tenance tes? phone and dial the next 
code (Diagnostic Test Access Code is 
not redialed). Recall dial tone is returned and the 
associaied DTMF receiver circuit LED 
in the DTMF PCB is extinguished. 
If no additional tests or procedures are The associated DTMF receiver circuit 
to be performed, place the main- LED in the DTMF PCB is extin- 
tenance test phone on-hook. guished.  Dial tone is returned. 
Recall dial tone is returned. 
None. 
Dial tone returned and the associat- 
ed DTMF receiver circuit LED in the 
DTMF PCB is lit steadily. IF VERIFICATION 
IS NOT OBTAINED 
If busy tone is returned, the DTMF 
receiver circuit is busy. Retry later. If 
intercept tone is returned, the DTMF 
receiver circuit is not assigned (check 
data base assignment). 
If intercept tone is returned at any 
time, either the DTMF receiver or the 
maintenance phone’s key-pad is nc? 
operating properly, or the buttons 
were depressed in the wrong se- 
quence. Retry test with another DTMF 
phone. If intercept tone is returned 
again, replace the DTMF receiver 
circuit. 
Table 6.03 Station Line Test 
NOTES: 1) If the system option flag TSTDIAG has been enabled in the data base or the station under test is c!assmarked 
with the TSTAPP feature, the maintenance test phone is not required to enable or disable the Apparatus Diagnos- 
tic Test routines; therefore, perform only steps 5 through 10. 
2) If the system option flag TSTDIAG has been disabled in the data base or the station under test is not classmarked 
with the TSTAPP feature, the maintenance test phone is required to enable or disable the Apparatus Diagnostic 
Test routines; therefore, oerform the entire procedure (steps 1 throuqh 11). 
STEP 
. 
PROCEDURE VERIFICATION 
Place maintenance test phone 
off-hook. Dial tone is returned. 
Dial the Diagnostic Test Access Code. 
Dial 3 to enable the Apparatus tests. 
Place the maintenance test phone 
on-hook. Recall dial tone is returned. 
Confirmation tone is returned. 
None. 
Place the station under test off-hook. Dial tone is returned 
;:;ethe Test-Station Line Access Confirmation tone is returned. IF VERIFKATION 
IS NOT OBTAINED 
1 
6-14  
						

							SATURN IIE EPABX 
Installation Test Procedures A30808-X5130-B120-l-8928 
Issue 1, May 1986 . 
Tab!c A.03 Station Line Test fCnntinc)edl 
, STEP 
PROCEDURE 
\-----------I 
STEP FROCEDUZZ VERIFICATTION IF VER!FiCATION 
IS NOT OBTAINED ’ 
7 Place station under test on-hook. Ringing returned. 
If ringing is not heard, switch the sta- 
tion instrument to determine if it is 
defective. If ringing is still not heard, 
replace the associated subscriber line 
PCB. 
8 Pick up handset to answer test tail. 
9 Verify that the test tone level is cor- Test tone (1004Hz @ -lGdBm) is If the returned test tone level is weak, 
rect by using a TMS. returned. swap the instrument to determine if it 
is defective If the test tone level in- 
creases considerably, replace the s:a- 
tion instrument. If test tone level 
remains weak, replace the associat- 
ed subscriber line PCB (SLMA, 
10 
Place station under test on-hoo!(. SLA16 or SLMD). 
None. 
11 
If no additional Test routines are to be 
performed, proceed as follows: 
Place maintenance test phone Dial tone is returned. 
off-boo!
						

							SATURN IIE EPABX A30808-X5130-B120-l-B928 
instaliation Test Procedures Issue 1, May 1986 
Wbtc 6.04 DTMF Pad Test 
STEP PWO@EDWE VERIFICATION IF VERIFICATIGN 
IS NOT OBTAINED 
7 Depress the DTMF keypad buttons in Recall dial tone ceases. After all the If busy tone is returned at any time, 
the following sequence: DTMFjteypad buttons are depressed either the DTMF key pad buttons were 
in the sequence indicated, test tone depressed in the wrong sequencethe 
For 12-button phones: 1, 2, 3, 4, 5, 6, (1004Hz @ -16dBm) is returned for DTMF keypad of the station under test 
7, 8, 9, 0, 4 and #. one minute. is defective or the subscriber line cir- 
cuit is defective. 
For 16-button phones: A, B, C, D, 1, 
2, 3, 4, 5, 6, 7, 8, 9, 0, * and #. To locate failure, retry test to verify that 
the keypad buttons were not 
depressed out of sequence. If 
problem persists, swap the station in- 
strument to determine ii it is defective. 
If problem remains, replace the rp- 
propriate subscriber line PCB. 
8 F;Q;he level of test tone by using If the measured test tone is correct 
but is weak, replace the station set. 
If the measured tone is low, rep!ace 
the subscriber line PCB SLMA or 
SLA16). 
9 Place DTMF station under test on- None. 
hook to terminate test. 
10 If no additional apparatus tests are to 
be performed, proceed as foilows: 
Place maintenance test phone Dial tone is returned. 
off-hoo!(. 
Dial the Diagnostic Test Access Code. Recall dial tone is returned. 
Dial 2 to disable the Apparatus Tests. None. 
Place maintenance test phone None. 
on-hook. 
Table 6.05 Console Test 
NOTES: 1) If the system option flag TSTDIAG has been enabled in the data base, the maintenance test phone is not required 
to enable and disable the Apparatus Test routines; therefore, perform only steps 5 through 9. 
2) If the system option flag TSTDIAG has been disabted in the data base, the maintenance test phone is required 
to enable and disable the Apparatus Test routines; therefore, perform the entire procedure (steps 1 through 10). 
STEP PROCEDURE VERIFICATION IF VERIFICATION 
IS NO-i- OBTAINED 
1 Place maintenance test phone Dial tone is returned. 
off-hook. 
2 Dial the Diagnostic Test Access Code. Recall dial tone is returned. 
3 
Dial 3 to enable the Apparatus Tests. Confirmation tone is returned. 
4 
Place maintenance test phone None. 
on-hook. 
5 
At the Console under test dial the At- Recall dial tone is returned. Also the If reorder tone is returned, the Atten- 
tendant Console Test access code access code is displayed momentar- dant Console Test routine is in use, 
when the console is in an idle state. ily, then the display changes to CON- retry later. 
SOLE TEST and all button LEDs are 
extinguished. 
6-16  
						

							SATURN IIE EPABX A30808-X5130-B120-l-8928 
Installation Test Procedures Issue 1, May 1986 
Table 6.05 Console Test (Continued) 
:TE? PRCCEDURE VERIFICATIDN lF VERlFlCATlON 
IS NOT OBTAINED + 
6 Depress the console’s keypad buttons All digits dialed are displayed (ac- If proper verification is not obtained or 
in the following sequence: 1, 2, 3, 4, cumulate). busy tone is returned at any time, the 
5, 6, 7, 8, 9, 0, * and #. keypad buttons or console buttons 
were depressed out of sequence, the 
7 Depress the console’s feature buttons Each button LED lights when console is defective, or PIMD circuit 
in the sequence shown in Figure 6.19.’ depressed and extinguishes when the is defective. To isolate the failure, retry 
next key is depressed. test to verify that the buttons were not 
depressed out of sequence. 
a After the last button in the sequence Groups of eight of each of the display- If proper verificaiion is not obtained or 
is depressed, depress any console able characters are scrolled in the se- busy tone is returned again, replace 
button to initiate the display test. The quence shown in Table 6.06. Ai-ier the associated PIMD PCB to verify 
display can be suspended by last character is displayed (under whether the PIMD circuit or the con- 
depressing any key on the console score character), the display unit is sole is defective. If proper verificaiion 
and resumed in the same manner. cleared and the following LEDs is obtained, replace the associa?ed 
momentarily light then extinguish in PIMD PCB. If proper verification is not 
the following sequence: obiained or busy tone is returned 
again, replace the console. 
a) TRUNK GROUP STATUS 1 - 
b) %“RCE 
c) DESTINATION 
d) ALERT 
e) CW 
9 MAJ ALM 
g) MIN ALM 
After the above indications are com- 
pleted the fo!lowing indications occur: 
Ringbeck tone is returned. 
All LEDs on the display assembly 
flash.. . 
After the above indications are com- 
pleted the following indications occur: 
Ringback tone is returned. 
All LEDs on the display assembly 
flash. 
The audible alerting device sounds at 
intervals. 
REMOVE HANDSET is displayed. 
9 Remove and reinsert handset assem- INSERT HANDSET is displayed while 
bly to terminate test, or wait 30 se- handset is removed. After handset is 
conds for test timeout. reinserted, console returns to normal 
operation. 
10 If no additional apparatus tests are to 
be performed, proceed as follows: 
Place maintenance test phone Dial tone is returned. 
off-hook. 
Dial the Diagnostic Test Access Code. Recall dial tone is returned. 
Dial 2 to disable the Apparatus Tests. None. 
Place maintenance test phone None. 
on-hook. 
6-17  
						

							I 
- 
SATURN IIE EPABX 
A30808-X5130-8120-143928 
installation Test Procedures 
Issue 1, May 1986 
TRUNK GGOUPSTATUS 
nnnnnnnn k 
(ALPHANUMERIC DISPLAY LNI;) 
SOUlxi OESTIXATION 
00000000 
li 18 19 20 21 22 23 24 
ALERT CL1 
Figure 6.19 Attendant Console Keypad and Feature Button Depression Sequence  
						

							SATURN IIE EPABX 
A30808-X5130-B120-l-6926 
Installation Test Procedures 
Issue 1, May 1986 
Table 6.06 Attendant Console Displayable Characters 
ORDER 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
11. 
12. 
13. 
14. 
15. 
16. 
17. 
18 19. 
20. 
2’:. 
23: 
24. 
25. 
26. 
27. 
28. 
29.  30. 
31. 
32. CHARACTER 
I I I I I I ! ! 
;;;;,A!,;;;; 
$$$$5$$$ 
o/o o/o 010 o/o o/o o/o o/o % 
&&&&&&&& 
I I I I I I I I 
( ( ( ( ( ( ( ( 
) 1 1 1 1 1 1 1 
* l * * * l * * ++++++++ 
I I > 9 I 1 3  I 
- - - - - - - - 
i i i i i i i i 
00000000 
1 1 1 1 1 1 1 1 
22222222 
33333333 
44444444 
55555555  66666666 
77777777 
88888888 
99999999 
: : : : : : : : 
; ; ; ; ; ; ; ; 
(((((((C 
TPffSf=>S 
???????? 
OQOQ@@@@ ORDER 
CHARACTER 
33. AAAAAAAA 
34. BBBBBBBB 
cccccccc 
ii: DDDDDDDD 
37. EEEEEEEE 
FFFFFFFF 
:i 
GGGGGGGG 
40: HHHHHHHH 
41. I I I I I I I I 
42. JJJJJJJJ 
43. 
K K K K K K I< K 
44. LLLLLLLL 
45. MMMMMMMM 
46. NNNNNNNN 
47. 00000000 
48. PPPPPPPP 
49. QQQQQQQQ 
50. RRRRRRRR 
51. ssssssss 
52. TTTTTTTT 
54. 53. vvvvvvvv  uuuuuuuu 
55. wwwwwwww 
56. xxxxxxxx 
2; YYYYYYYY 
zzzzzzzz 
59: 
[ I [ 1 I 1 1 I 
60. 
61. \\\\))) 
1 1 I I 62. A A A A ,I> A A A 
63. 
----_--- 
6-19  
						

							I . 
SATURN IIE EPABX A30808-X5130-B120-I-6928 
Installation Test Procedures Issue 1, May 1986 
Table 6.07 Siemcns Digital Telephone - DVAD Dutton Test 
NOTES: 1) If the system option flag TSTDIAG has been enabled in the data base or the Siemcns Digital Telephone under 
test is classmarked with TSTAPP feature, the maintenance test phone is nbt required to enable or disable the 
Apparatus Diagnostic routines; therefore, perform only steps 5 through 9. 
2) If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under 
test is not classmarked with the TSTAPP feature. the maintenance test phone is required to enable or disable 
the Apparatus Diagnostic routine? 
s; t herefore, perform the entire procedure (steps 1’ through 10). 
STEP 
1 
2 
3 
4 
5 
6 
7 
8 
9 
10 PROCEDURE . VERIFICATION 
‘lace the maintenance test phone 
,ff-hook. 
3ial the Diagnostic Test Access Code. 
Iial 3 to enable the Apparatus Diag- 
lostic Tests. 
‘lace maintenance test phone 
x+hook. 
‘lace Siemens DYAD Telephone 
,ff-hook. 
Dial the Siemens Digital Telephone 
rest Access Code. 
Ieoress the Siemens DYAD Telc- 
&ne keypad buttons as, fo!lows: 1, 
3, 3, 4, 5, 6, 7, 8, 9, 0, * , i?. 
Depress the DYAD feature buttons in 
the sequence shown in Figure 6.20 
and according to the Siemens DYAD 
Telephone model. 
Place Siemens DYAD Telephone un- Siemens DYAD Telephone returns to 
der test on-hook to terminate test. normal operation. 
If no additional Apparatus Diagnostic 
Test routines are to be performed, pro- 
ceed as follows: 
Place maintenance test phone 
off-hook. Dial tone is returned. 
Dial the Diagnostic Test Access code. Recall dial tone is returned. 
Dial 2 to disable the Apparatus Diag- 
nostic Test. None. 
Place maintenance test phone on- 
hook.None. None.  Iial tone is returned. 
qecall dial tone is returned. 
>onfirmation tone is returned. 
Uone. 
Iial tone is returned. 
secall dial tone is returned. 
The access code is momentarily dis- f reorder tone is returned, the Sie- 
3layed, then the display unit and but- nens DYAD Telephone 
Button Test is 
ton LEDs are extinguished. n use, try later. 
Button LEDs light when depressed 
and extinguish when the next button 
is depressed. 
After the last button is depressed, the 
following indications occur: 
Ringback tone is returned. 
All button LEDs flash. 
The audible alerting device sounds at 
intervals. 
TEST COMPLETE is displayed. IF VERiFICATlON 
IS NOT OBTAINED 
f proper verification is not obtained cr 
xsy tone is returned at eny time, 
either the keypad buttons cr featuie 
buttons were depressed out of se- 
quence, the DYAD Telephone is defac- 
tive, or the SLMD circuit is defective. 
To isolate the failure, retry test to veri- 
fy that the buttons were not depressed 
Dut of sequence. 
If proper verification is not obtained or 
busy tone is returned again, replace 
the Siemens DYAD Telephone under 
test with a known good DYAD Tele- 
phone and retry test. If proper verifi- 
cation is not obtained or busy tone is 
returned again, replace the SLMD 
PCB. 
I 
- 
6-20  
						

							I 
- 
SATURN HE EPABX 
Installation Test Procedures A30808-X5130-8120-1-8928 
Issue 1, May 1986 
IS BUTTON 
DYAD 
26 BUTTON 
DYAD 
SEE NOTE 
NOTE: These buttons do not 
contain LEDs. 
SEE NOTE y 
/ ’ 
I 
Figure 6.20 Siemens DYAD Telephone Button Depression Sequence 
6-21  
						

							SATURN IIE EPABX 
Installation Test Procedures A30808-X5130-BlZO-l-8928 
Issue 1, May 1986 
Table 6.06 Siemcns Digital Telephone - JR-DYAD Button Test 
NOTES: 1) If the system option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under 
test is classmarked with TSTAPP feature, the maintenance test phone is ‘not required to enable or disable the 
Apparatus Diagnostic routines; therefore, perform only steps‘5 through 9. 
2) If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under 
test is not classmarked with the TSTAPP feature, the maintenance test phone is required to enab!e or disable 
the Apparatus Diagnostic routines; therefore, perfcrm ihe entire procedure (steps 1 through i0). 
STEP PROCEDURE VERIFICATION IF VERIFICATION 
IS NOT OBTAINED 
1 Place the maintenance test phone Dial tone is returned. 
off-hook. 
2 Dial the Diagncstic Test Access Code. Recall dial tone is returned. 
3 Dial 3 to enable the Apparatus Diag- Confirmation tone is returned. 
nostic Tests, 
4 Place maintenance test phone None. 
on-hook. 
5 Place JR-DYAD Telephone off-hook. Dial tone is rereturned. 
6 Dial the Siemens Digital Telephone Recall dial tone is returned. If reorder tone is returned, the Sie- 
Test Access Code. mens JR-DYAD Telephcne Button Test 
is in use, try later. 
7 Depress the Siemens JR-DYAD Tele- Ii proper verification is net obtainsd or 
phone keypad buttons as, follows: 1, busy tone is returned at any iime, 
2, 3, 4, 5, 6, 7, 8, 9, 0, * , #. either the keypad buttons or feature 
buttons were depressed out of se- 
8 Depress the JR-DYAD feature buttons Button LEDs light when depressed quence, the JR-DYAD Telephone is 
in the sequence shown in Figure 6.21. and extinguish when the next button defective, or the SLMD circuit is 
is depressed. defective. To isolate the failure, retry 
test to verify that the buttons were not 
After the last button is depressed, the depressed out of sequence. 
following indications occur: 
If proper verification is not obtained or 
Ringbac!c tone is returned. busy tone is returned again, replace 
All button LEDs flash. the Siemens JR-DYAD Telephone un- 
der test with a known good JR-DYAD 
The audible alerting device sounds at Telephone and retry test. If proper 
intervals. verification is not obtained or busy 
tone is returned again, the SLMD cir- 
cuit is defective and the SLMD PC6 
requires replacement. 
9 
Place Siemens JR-DYAD Telephone Siemens JR-DYAD Telephone returns 
under test on-hook to terminate test. to normal operation. 
10 If no additional Apparatus Diagnostic 
Test routines are to be performed, pro- 
ceed as follows: 
P&tokmaintenance test phone Dial tone is returned. 
Dial the Diagnostic Test Access code. Recall dial tone is reiurned. 
Dial 2 to disable the Apparatus Diag- None. 
nostic Test. 
Place maintenance test phone None. 
on-hook. 
6-22