Siemens Saturn Iie Epabx General Description Manual

							I 
- 
SATURN IIE EPABX A30808-X5130-B120-l-8928 
Installation Test Procedures Issue 1, May 1986 
NOTES: 
* These feature buttons are not testable. 
Buttons 9 through 13 do not contain LEDs. 
Figure 6.21 Siemeno JR-DYAD Telephone Button Depression Sequence 
6-23  
						

							I . I 
- 
SATURN IIE EPABX 
Installation Test Procedures A30808-X5130-B120-l-8928 
Issue 1, May 1986 
Table 6.09 Siemens Digital Telephone -DYAD Display Test 
NOTES: 1) If the system 
option flag TSTDIAG has been enabled in the data base or the Siemens Digital Telephone under 
test is classmarked with TSTAPP feature, the maintenance test phone is not required to enable or disabie the 
Apparatus Diagnostic routines; therefore, perform only steps 5 through 9. 
2) If the system option flag TSTDIAG has been disabled in the data base or the Siemens Digital Telephone under 
test is not classmarked with the TSTAPP feature, the maintenance test phone is required to enable or disable 
the Apparatus Diagnostic routines; therefore, perform the entire procedure (steps 1 through 10). 
XEP PROCEDURE VERIFICATION IF VERIFICATION 
IS NOT OBTAINED 
1 Place maintenance test phone Dial tone is returned. 
off-hook. . 
./ ; 
2 Dial the Diagnostic Test Access Code. 
Recall dial tone is returned. 
3 Dial 3 to enable the Apparatus Diag- Confirmation tone is returned. 
nostic test. 
4 Place maintenance test phone None. 
on-hcok. 
5 Place the Siemens Digital Telephone Dial tone returned. 
under test off-hook. 
G Dial the Siemens Digital Telephone Recall dial tone is returned. The Ac- If reorder tone is returned, the Sie- 
test access code. cess code is momentarily displayed, mens Digital Telephone Display Test 
then the display unit clears. is being used, retry later. 
7 Depress any button in the Siemens Groups of 16 of each of the displaya- If verification is not obtained, either 
Digital Telephone under test to initiate ble characters are scrolled in the se- the Siemens Digital Telephone or the 
test. quence shown in Table 6.09. After the SLMD circuit is defective. Replace 
last characier (underscore) is dis- Siemens Digital Telephone with a 
(Note: The display test can be sus- played the following occurs: good one and retry test. If verification 
pended any time by depressing any is obtained, replace the Siemens Dig- 
button. The test can be resumed at Ringback tone is returned. ital Telephone. 
any time in the same manner.) 
All button LEDs flash and the audible If verification is still not obtained, 
alerting device sounds at intervals. replace the SLMD PCS. 
TEST COMPLETE is displayed. 
8 Place Siemens Digital Telephone on- 
hook to terminate test or wait 30 se- 
conds for test timeout. 
9 If no additional Apparatus Diagnostic 
Tests are to be performed, proceed as 
follows: 
Place maintenance test phone Dial tone returned. 
off-hook. 
Dial the Diagnostic Test Access Code. Recall dial tone is returned 
Recall dial tone returned. 
Dial 2 to disable the Apparatus Diag- None. 
nostic Test. 
Place maintenance test phone None. 
on-hook. 
G-24  
						

							i . 
I 
SATURN IIE EPABX 
A30808-X5130-B120-l-6928 
Installation Test Procedures 
Issue 1, May 1986 
Table 6.10 Siemens Digital Telephone Displayable Characters 
ORDER CHARACTER 
ORDER CHARACTER 
1. ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! 33. 
AAAAAAAAAAAAAAAA 
2. #P It It I, I, ,I 0 0 I, r, 0 I, 0 I, ,I I, 34, BBBBBBBBBBBBBBBB 
3. #H#H#####,Y###### 35. cccccccccccccccc 
4. $ssssss$s$s$s$s$ 36. DDDDDDDDDDDDDDDD 
5. o/b 010 vo %%%% vo vo o/o %% o/o %% o/o 
37. EEEEEEEEEEEEEEEE 
6. &&&&&&&&&&.&&&&&& 38. FFFFFFFFFFFFFFFF 
7. 39. GGGGGGGGGGGGGGGG 
8. ;;;;;;;;;1;;;;;; 40. HHHHHHHHHHHHHHHH 
9. 
))))))))))))))I) 41. 
I I I I I I I I I I I I I I I I 
10. **************** 42. JJJJJJJJJJJJJJJJ 
11. -I-+++++++++++++++ 43. KKKKKKKKKKKKKKKK 
12. 0000000e00.0.0.. 44. LLLLLLLLLLLLLLLL 
13. --------------- 45. MMMMMMMMMMMMMMMM 
14. 46. NNNNNNNNNNNNNNNN 
15. GE;;;;;;;;;;; 47. 0000000000000000 
16. 0000000000000000 48. PPPPPPPPPPPPPPPP 
17. 1111111111111111 49. QQQQQQQQQQQQQQQQ 
18. 2222222222222222 50. RRRRRRRRRRRRRRRR 
19. 3333333333333333 51. ssssssssssssssss 
20. 4444444444444444 52. TTTTTTTTTTTTTTTT 
21. 5555555555555555 53. uuuuuuuuuuuuuuuu 
22. 6666666666666666 54. vuvvvvuvvvvvuvvv 
23. 7777777777777777 55. wwwwwwwwwwwwwwww 
24. 8888888888888888 56. xxxxxxxxxxxxxxxx 
25. 9999999999999999 57. YYYYYYYYYYYYYYYY 
26. . . . * . . . . . . . . . . . . 
. . . . . . . . . . . . . . . . 58. zzzzzzzzzzzzzzzz 
27. . . . . . . . . . . . . . . . . 
28. ~~~~t~~~~i~i~lii 59. 11 1 [ I [ [ [ 11 I[ [ [ [ [ 
GO. 
29.   \>           :   
========zz== 
30. ff~~~,,,,,,,,,,, 61. 
11 1 I II 1111111111 62. AAAAAAAAAAAAAAAA 
31. ???????????????? 63. 
- - - - - _ _ _ 
32. Q@Q@@@@@@@@Q@QOQ 
6-25  
						

							SATURN IIE EPABX 
‘nstallation Test Procedures 
Table 6.11 Outgoing Trunk Test A30808-X5130-8120-l-8928 
Issue 1, May 1986 
STEP 
1 
5 
6 
7 
8A 
8B PROCEDURE VERlFiCATlCN 
?lace maintenance test phone 
off-hook. 
Dial the Diagnos?ic Test Access Code. 
Dial 2 to enable trunk test. 
Dial the two-digit trunk group number 
(00 through 31) coniaining the trunk 
circuit to be tested. 
Dial the two-digit trunk number (00 - 
99) of the trunk circuit to be tested. 
For CO-type trunks (i.e., TMBM PCB), 
dial the test tone number provided by 
the local phone company. 
Verify that the returned test tone lev- 
el is correct, using a TMS. 
If additional tests or procedures are 
to be performed, hook-flash the main- 
tenance test phone and dial the next 
code (Diagnostic Test Access Code is 
not redialed). 
If no additional tests or procedures are 
to be performed, place the main- 
tenance test phone on-hook. Iial tone is returned. 
jecall dial tone is returned. 
done. 
done. 
20 or PABX dial tone is returned. 
41~0, the associated irunk circuit LED 
In the trunk PCB is lit steadily to in- 
licate the trunk has been seized 
Iutgoing. 
Test tone (1004Hz) is returned 
Recall dial tone is returned. 
None. IF VERIFICATION 
IS NOT OETAINED 
I j 
If reorder tone is returned, the select- 
ed trunk circuit is either an incoming- 
type, invalid, or not assigned (chec!c 
data base assignments). 
If busy tone is reiurned, the selected 
trunk is in use, retry later. 
If CO or PABX dial tone is not 
returned, verify trunk MDF cross- 
connections and attempt to access 
CO/PABX trunk using a butt set. If the 
trunlc is working properly replace the 
trunk PCB under test and retry test. 
If the reiurned test tone level is weak, 
replace PCB with another having the 
same characteristics and retry test. If 
returned test tone level increases con- 
siderably, trunk PCB is defective and 
should be replaced. If the test tone 
level is still weak, contact CO repair 
service to verify trunk facility. i 
i 
6-26  
						

							- 
SATURN IIE EPABX A30i308-X5130-B120-1-B928 
Installation Test Procedures Issue 1, May 1986 . 
Table 6.12 Placing Circuit(s) In-Service 
STEP PROCEDURE VERIF!CATION IF VERlFlCATIOfl 
IS NOT OBTAiNED * 
1 Place maintenance test phone Dial tone is returned. 
off-hook. 
2 Dial the Diagnostic Test Access Code. Recall dial tone is returned. 
3 Dial 7 for placing a circuit in-service. None. 
4A If a single circuit is to be placed in- Coniirmation tone is returned. If reorder tone is returned, the seleci- 
service, dial the four digit PEN num- ed circuit is invalid or unassigned. 
bar of the circuit. Check data base assignments. 
45 If all the circuits in a PCB are to be Confirmation tone is returned. If reorder tone is returned the select- 
placed in-service, dial the first three ed PCB is invalid or unassigned 
digits of the PEN number for the PCB Check data base assignments, 
followed by digit 8. For an SLA16, dial 
the first three digits of the PEN num- 
ber associated with the first eight cir- 
cuits followed by an 8, then dial the 
first three digits of the associated PEN 
number for the second eight circuits 
(W,X,Y+l) followed by an 8. 
5A 
If additional t&s or procedures are Recall dial tcne is returned. 
to be performed, hoolcilash the main- 
tenance test phcne and dial the next 
code (Diagnostic Test Access Code is 
not redialed). 
5B If no additional tests or procedures are None. 
to be performed, place the main- 
tenance test phone on-hook. 
Table 6.73 Taking Ci:cuit(s) Out-et-Service 
STEP PROCEDURE VERIFICATION IF VERlFtCATION 
IS NOT OBTAINED 
1 Place maintenance test phone Dial tone is returned. 
off-hook. 
2 
Dial the Diagnostic Test Access Code. Recall dial tone is returned. 
3 Dial 8 for placing a circuit out-of- None. 
service. 
4A 
48 If a single circuit is to be placed out- Confirmation tone is returned. If reorder tone is returned, the select- 
of-service, dial the four digit PEN ed circuit is invalid or unassigned. 
number of the circuit. Check data base assignments. 
If all the circuits in a PCB are to be Confirmation tone is returned. If reorder tone is returned the select- 
placed out-of-service dial the first ed PCB is invalid or unassigned. 
three digits of the PEN number for the Check data base assignments. 
PCB followed by digit 8. For an SL416, 
dial the first three digits of the PEN 
number associated with the first eight 
circuits followed by an 8, then dial the 
first three digits of the associated PEN 
number for the second eight circuits 
(W,X,Y+l) followed by an 8. 
6-27  
						

							I ’ 
SATURN IIE EPABX 
installation Test Procedures 
Table 6.13 Takinq Circuit(s) Out-of-Service IContinucdl 
A30808-X5130-8120-1-8928 
Issue 1, May 1986 
. , 
STEP 
PROCEDURE VERIFICATION IF VERIFICATION 
IS NOT OBTAINED 
5A 
If additional tests or procedures are Recall dial tone is returned. 
to be performed, hook-flash the main- 
tenance test phone and dial the next 
code (Diagnostic Test Access Code is 
not redialed). 
5B If no additional tests or procedures are None. 
to be performed place the main- 
tenance test phone on-hook. .: j 
6-28 (28 pages)  
						

							I 
.-- 
SATURN IIE EPABX 
A30808-X5130-B120-143928 
Installation Test Procedures Issue 1, May 1986 
SECTKIN 7.00 INSTALLATION TEST PROCEDURES CHECKLlST 
7.01 General. After performing the installation test proce- 
dures contained in this practice, each installation test proce- 
dure performed should be recorded to ensure that all tests have been completed satisfactorily. Use Table 7.00, Installa- 
iion Test. Procedures Checklist, for this purpose. This table 
can be used as a sign-off sheet, if required. 
Table 7.00 Installation Test Procedures Checklist 
7-l (7-2 bl!nnL,)  
						

							Siemens Pracltces 
Maintenance Series A30808-X5130-DllO-18920 
Issue 1, May 1986 
SATURN” IIE EPABX 
MAINTENANCE AND TWQU 
ESH~O=~I 
Issued by Office Systems Group 
5500 Broken Sound Boulevard N.W.. Boca Raton. Florida 33431 
- - .-_ .~__- - 
Stemens lnformatlon Systems, Inc. (305) 994-8100 l Telex: 515052 
Printed in U.S.A.  
						

							Siemens Practices 
,.’ Maintenance Series A30808-X5130-DIIO-l-8920 
Issue 1, May 1986 
0 Siemens Information Systems, inc., 1985 
All rights reserved. 
- i 
I 
-: 
This material is proprietary to Siemens Information Systems, Inc. Any unauthorized 
reproduction, use or disclosure of this material, or any part thereof, is strictly prohibited. 
Siemens reserves the right to make changes in specifications at any time and without 
notice. The information furnished by Siemens in this material is believed to be accurate 
and reliable. However, no responsibility is assumed by Siemens for its use. 
SATURN is a registered trademark of Siemens Information Systems, Inc. 
/ 
‘I  
						

							SAUTRN IIE EPABX  A30808-X5130-DllO-l-8920 
Maintenance  and Troubleshooting  Issue 
1, May  1986 
CONTENTS  I 
--. 
SECTION  PAGE 
FIGURE  PAGE 
................. ....... l-l 
Purpose..  .......................  ...... 
1-l 
Scope  ...........................  ......  l-l 
Siemens  SATURN  IIE Practices  ......  ......  1-l 
Siemens  Customer  Support Services  ...... 
l-l 
What  to Do  in Case  of Trouble  with 
FCC-Registered  Equipment, ....... 
. l-l 
2.00  MAINTENANCE  OVERVIEW ................ 
2-l 
Introduction  ...............................  2-1 
General  ..................................  2-l 
Design  Considerations  ......................  2-2 
Maintenance  Facilities ......................  2-2 
Power  System  Unit .........................  2-2 
Maintenance  Phone ........................  2-4 
Service  Terminal  ........................... 
2-4 
Manual  On-Line  Diagnostic  Tests. .............  2-7 
System  Diagnostic  Tests. .................... 
2-7 
Apparatus  Diagnostic  Tests .................. 
2-8 
Automatic  On-Line Diagnostic  Testing 
and  Reporting  ........................... 
2-9 
Self-Test  Routines  ..........................  2-9 
Audit  Routines  ............................  2-10 
Alarm  Indicators  and Classification  ........... 
2-11 
Power  Distribution  and Failures  ..............  2-11 
3.00  PREVENTIVE  MAINTENANCE  ..............  3-l 
General  ..................................  3-1 
Floppy  Disk Drives  ..........................  3-1 
4.00  TROUBLESHOOTING  AND REPAIR 
PROCEDURES  .........................  4-1 
General  ..................................  4-l 
Test  Equipment  ............................  4-1 
PCB  and Power  Supply  Removal  and 
Replacement  ................... 
System  Fails to Reload.  ............ 
Alarm  Conditions  and Reporting  ......... 
Power  Failures.  .......................  4-l  
4-1 
4-l 
:  ‘4-18 
Single-Line  Telephone Related Failures  ....... 4-27 
Attendant  Console Related Failures  .......... 
4-28 
Siemens  Digital Telephone  (SDT) 
Related  Failures  .  .  .  .  .  .  . 
Manual  On-Line  Diagnostic  Tests .  . 
Automatic  On-Line Audit Tests,  .  .  .  . 
Spare  Parts  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4-28  
4-30 
4-30  
4-30 
FIGURE 
LIST  OF FlGlJRE!i 
PAGE 
1.00  SATURN  IIE System  Basic Cabinet  .  .  .  l-2 
1.01  SATURN  IIE System  with Basic  and 
Expansion  Cabinets .  .  .  .  .  .  .  .  1-3 
2.00  SATURN  IIE System  Block Diagram  2-l 
2.01  Power  System  Unit (PSU),  Front View  2-3 
2.02  Controller/Input-Output  Processor Printed 
Circuit  Board (CIOP)  .  .  . 2-5 
2.03  Remote  Access Unit/Ports  Printed Circuit 
Board  (RAUP)  .  .  2-6 
2.04  SATURN  IIE EPABX  Basic Cabinet, 
Front  View  2-12 2.05 
SATURN  IIE EPABX-Basic  Cabinet, 
Rear-View  ............................... 
2-13 
2.06  SATURN  IIE EPABX  Basic and Expansion 
Cabinets,  Front View  ......................  2-14 
2.07  SATURN  IIE EPABX  Basic and Expansion 
Cabinets,  Rear View  ...................... 
2-15 
2.08  Block  Diagram  of AC  Input  to Power  Supply 
Assemblies  and Modules  . 
.- 
................  2-17 
2.09  Layout  of Connectors  and Terminals  on 
Power  System  Unit (PSU)  Rear Panel  ........  2-18 
2.10  Fusing  of -48  Volt  Outputs  from -48PSO 
and  -48PSl  ..............................  2-19 
2.11  Power  System  Unit (PSU)  Block Diagram  ..... 2-21 
2.12  RAC/RMW  Signals ........................ 
2-24 
4.00  Power  System  Unit (PSU)  Power Connections  4-21 
4.01  -48PSO  Module Power Connections  .......... 4-22 
4.02  Basic  Shelf Backplane  Power Connections  .... 
4-24 
4.03  LTUPS  Module  Power Connections.  .......... 4-25 
4.04  LTU Shelf  Backplane  Power Connections.  ..... 4-26 
4.05  Attendant  Console Keypad and Feature  Button 
Depression  Sequence. .....................  4-37 
4.06  Siemens  DYAD Telephone  Button Depression 
Sequence  ...............................  4-42 
4.07  Siemens  JR-DYAD  Telephone  Button 
Depression  Sequence ...................... 
4-45 
LIST OF TABLES 
TABLE  PAGE 
1.00 Mnemonics  Used in This  Practice  ............ 
l-4 
2.00  Functions  of Connectors  and Terminals  on 
PSU  Rear  Panel  .........................  2-20 
2.01  Pin Functions  at Connector  J13 
on  the  PSU  .............................  2-25 
2.02  Alarm  LEDs and Output  Status at 
Connector  J13 on the  PSU  ................. 
2-25 
3.00  Floppy  Disk Head  Cleaning  Procedure  ........ 
3-l 
4.00  PCB  and Power  Supply  Removal  Guidelines  ... 4-2 
4.01  Failure  Indications  on Controller/input-Output 
Processor  Printed Circuit Board (CIOP)  ........  4-3 
4.02  Alarm  Reporting  and Processing  .............  4-4 
4.03  Failure  Indications  on LTUC  Printed  Circuit 
Board  ..................................  4-17 
4.04  Memory  Support Module (MSM) Battery 
Test  ....................................  4-17 
4.05  Allowable  Voltage Ranges  ..................  4-19 
4.06  Tone  Generator  Test ...................... 
4-31 
4.07  Tone  Generator  Test Numbers  .............. 
4-31 
4.08  Outgoing  Trunk Test ......................  4-32 
4.09  DTMF  Receiver  Test ......................  4-33 
4.10  Placing  Circuit(s)  In-Service  ................ 
4-33 
4.11  Taking-Circuit(s)  .Out-of-Service 
4.12  DTMF  Dial Pad Test 
4.13  Station  Line Test 
4.14  Attendant  Console Test  .  . 
4.15  Attendant  Console Displayable  Characters 
4.16  Siemens  DYAD Telephone  Button Test . 
4.17  Siemens  JR-DYAD Telephone  Button Test 
4.18  Siernens  DYAD Telephone  Display Test 
4.19  Siemens  DYAD Telephone  Displayable 
Characters  4-34 
4-35 
4-36 
4-38 
4-39 
4-40 
4-43  
4-46  
4-47