Sharp Mx 3501 N Manual

165
System Settings (Administrator) List
When the system settings are accessed with administrator rights, the following items appear. The factory default setting 
for each item is also shown.
Depending on the machine specifications and peripheral devices installed, it may not be possible to use some settings.
ItemFactory default settingPage
■Operation Settings171
●Keys Touch Sound
171XKeys Touch SoundMiddle
XKeys Touch Sound at Initial PointDisable
●Auto Clear Setting60 sec.171XCancel TimerDisable...

166
■Image Send Setting175
●Operation Settings175
XDefault Display Setting
175
‹ModeFax
‹Hold settings for a while after scanning has been 
completedDisable
‹Switch Automatically to Copy Mode ScreenEnable
XInitial Resolution Setting
175
‹Apply the Resolution Set when StoredDisable
‹Scan200X200dpi
‹Internet Fax*2200X100dpi
‹FaxStandard
XDefault Exposure Settings175
‹ExposureAuto175
‹Original Image TypeText175
‹Moiré ReductionDisable175
XMust Input Next Address Key at Broadcast SettingDisable176
XScan...

167
‹Disable Registering Destination on Web Page*3
177
 GroupDisable
 E-mailDisable
 FTPDisable
 DesktopDisable
 Network FolderDisable
 Internet FaxDisable
FaxDisable
‹Disable Registration Using Network Scanner 
Tools*3Disable177
XSettings to Disable Transmission177
‹Disable [Resend] on Fax/Image Send ModeDisable177
‹Disable Selection from the Address Book
177
 E-mailDisable
 FTPDisable
 DesktopDisable
 Network FolderDisable
 Internet FaxDisable
FaxDisable
‹Disable Direct Entry
177...

168
‹Speaker Settings
178
 SpeakerVolume: Middle
 Ringer VolumeVolume: Middle
 Line MonitorVolume: Middle
 Fax Receive Complete SignalVolume: Middle; Tone Pattern: 3
Transmission Complete Sound Time Setting: 3 sec.
 Fax Send Complete SignalVolume: Middle; Tone Pattern: 3
Transmission Complete Sound Time Setting: 3 sec.
 Fax Communication Error SignalVolume: Middle; Tone Pattern: 3
Transmission Complete Sound Time Setting: 
Every 0.3 seconds
‹Remote Reception Number Setting5179
‹Original Print on...

169
‹A3 RX ReduceDisable183
‹Anti Junk Fax Setting–183
‹Fax Output SettingsVaries depending on the machine configuration184
XFax Polling Security185
‹Polling Security SettingEnable185
‹Passcode Number Setting–185
■List Print (Administrator)186
●Administrator Settings List
186
XCopy –
XPrint–
XImage Send–
XDocument Filing–
XSecurity–
XCommon–
XAll Administrator Settings List–
●Image Sending Activity Report
186XImage Sending Activity Report (Scan)–
XImage Sending Activity Report (Internet Fax)–
XImage...

170
*1 When a large capacity tray is installed.
*2 When the internet fax expansion kit is installed.
*3 When network connection is enable.
*4 When the application integration module is installed.
XSettings to Disable the Registration of Destination187
‹Disable Registering Destination from Operation Panel
187
 GroupDisable
 E-mailDisable
 Internet FaxDisable
FaxDisable
‹Disable Registering Destination on Web Page*3
187
 GroupDisable
 E-mailDisable
 FTPDisable
 DesktopDisable
 Network...

171
Operation Settings
This section explains settings that are related to machine operation. Touch the [Operation Settings] key and configure 
the settings.
Keys Touch Sound
This setting is used to adjust (or turn off) the volume of 
the beep that sounds when you touch a key. You can 
also have three beeps sound at initial values when 
setting the ratio in copy mode or when adjusting the 
exposure in any mode.
Select one of the keys and touch the [OK] key.
When Key Touch Sound at Initial Point is...

172
Disabling of Bypass Printing
This setting is used to disable bypass printing (printing 
other jobs ahead of a job that has been stopped* 
because the paper required for the job is not in any of 
the trays).
To enable this setting, select the checkbox   and 
touch the [OK] key.
* This does not include cases where the paper ran out 
during the job.
Key Operation Setting
This setting determines how long a key in the touch 
panel must be touched until the key input is registered. 
The time can be set...

173
4Select the function that you wish to 
show in the customized key.
Select the key of the desired function and touch the [OK] 
or the [Details] key. Touch the [Details] key to open the 
advanced settings screen for the selected function. Select 
the desired settings and touch the [OK] key.
When the [OK] key is touched, a confirmation message 
will appear. Touch the [Yes] key to apply the selected 
function name to the customized key. (The name of the 
key can also be changed.)
5Touch the [OK] key.
If...

174
Device Control
These settings control devices installed on the machine. Touch the [Device Control] key and configure the settings.
Original Size Detector Setting
One of the five groups of standard original sizes shown 
below can be selected for detection by the original size 
detection function.
Select one of the keys and touch the [OK] key.
To disable detection of original sizes on the document 
glass, select the [Cancel Detection at Document Glass] 
checkbox   and touch the [OK] key.
Disabling of...