Ricoh Mp 6002 User Guide

							There are six types of Two-Sided Combine.
1 Sided 4 Originals 
 Combine 2 Sides
Copies four 1-sided originals to one sheet with two pages per side.
1 Sided 8 Originals 
 Combine 2 Sides
Copies eight 1-sided originals to one sheet with four pages per side.
1 Sided 16 Originals 
 Combine 2 Sides
Copies 16 1-sided originals to one sheet with eight pages per side.
2 Sided 4 Pages 
 Combine 2 Sides
Copies two 2-sided originals to one sheet with two pages per side.
2 Sided 8 Pages 
 Combine 2 Sides
Copies four 2-sided originals to one sheet with four pages per side.
2 Sided 16 Pages 
 Combine 2 Sides
Copies eight 2-sided originals to one sheet with eight pages per side.
1. Press [Dup./Combine/Series].
2.Press [Combine].
Combined Copying
59CKN074         
						

							3.Select [1 Sided] or [2 Sided] for [Original:].
4.Press [Combine 2 Sides].
5. Press [Orientation].
6. Select [Top to Top] or [Top to Bottom] for [Original:] and/or [Copy:], and then press
[OK].
7. Select the number of originals to combine.
8. Press [OK].
9. Select the paper size.
10. Place the originals, and then press the [Start] key.
3. Copy
60  
						

							Copying onto Custom Size Paper from the
Bypass Tray
Paper that has a horizontal length of 139.7–600.0 mm (5.50–23.62 inches) and a vertical length of
100.0–305.0 mm (3.94–12.00 inches) can be fed in from the bypass tray. Note however that the
limitation on the horizontal and vertical length range will vary depending on which options are installed.
• When prints are delivered to the trays of Finisher SR4060 or Booklet Finisher SR4070: Horizontal length: 139.7–487.6 mm (5.50–19.19 inches), vertical length: 100.0–305.0 mm
(3.94–12.00 inches)
• When prints are delivered to the upper tray of Finisher SR4080: Horizontal length: 139.7–458.0 mm (5.50–18.03 inches), vertical length: 100.0–305.0 mm(3.94–12.00 inches)
• When prints are delivered to the shift tray of Finisher SR4080: Horizontal length: 139.7–458.0 mm (5.50–18.03 inches), vertical length: 139.0–305.0 mm(5.48–12.00 inches)
1. Load the paper face up in the bypass tray.
[Bypass] is automatically selected.
2. Press the [
] key.
3. Press [Paper Size].
4. Press [Custom Size].
5. Enter the horizontal size with the number keys, and then press [
].
6.Enter the vertical size with the number keys, and then press [].
7. Press [OK] twice.
8. Place the originals, and then press the [Start] key.
Copying onto Custom Size Paper from the Bypass Tray
61     
						

							Finishing
Staple
Each copy set can be stapled together.
• You cannot use the bypass tray with this function.
Original orientation and staple position
Place all the originals in the ADF in the orientation in which they can be read normally. Whenplacing the original on the exposure glass, keep the same orientation, but place the original facing
downwards.
When the paper that is loaded is the same size and orientation as the original, the relationship
between the orientation in which you place the original and the staple positions is as follows. You
can confirm the staple positions that can be selected on the screen that appears when [Finishing] is pressed.
Placing the original on the exposure glassPlacing the original in the ADFStaple position *1Top 1SlantBottom 13. Copy
62CKN021       *2      
						

							Placing the original onthe exposure glassPlacing the original in the ADFStaple position *1Left 2Top 2Center
*1
The above tables show staple positioning. The orientation of the paper does not indicate orientation of
delivery.
*2 You cannot staple at this position when copying onto B4 JIS, 8 × 13 or larger.
*3 If you want to staple at this position, select unreadable orientation in [Original Orientation], and then
select Top 2.
1. Press [Finishing].
2.Press [Finisher].
Finishing
63  *2   *2 *3 *3      
						

							3.Select one of the staple positions.
When you select a staple position, Sort is automatically selected.
4. Press [OK].
5. Enter the number of copy sets with the number keys.
6. Place the originals, and then press the [Start] key.
Punch
You can make punch holes in copies.
The available number of punch holes is shown below:
(mainly Europe and Asia): 2 holes, 4 holes
(mainly North America): 2 holes, 3 holes
• You cannot use the bypass tray with this function.
• You cannot use Z-fold with this function.
Original orientation and punch hole position
Place all the originals in the ADF in the orientation in which they can be read normally. Whenplacing the original on the exposure glass, keep the same orientation, but place the original facing
downwards.
3. Copy
64CKN022      
						

							When the paper that is loaded is the same size and orientation as the original, the relationshipbetween the orientation in which you place the original and the punch hole positions is as follows.
You can confirm the punch hole positions that can be selected on the screen that appears when
[Finishing] is pressed.Placing the original on the exposure glassPlacing the original in the ADFPunch hole position *12 hole left2 hole top3 hole left3 hole top4 hole left4 hole top
*1
The above table shows punch hole positioning. Punched sheets might not be delivered in the orientation
shown in this table.
*2 You cannot punch holes in this position when copying onto B4 JIS, 8 × 13 or larger.
*3 If you want to punch holes in this position, select unreadable orientation in [Original Orientation], and
then select the punch hole position.
Finishing
65  *2   *3
*2 *3   *2   *3 *2 *3   *2   *3 *2 *3   
						

							1.Press [Finishing].
2.Press [Finisher].
3. Select one of the punch hole positions.
4.Press [OK].
5. Enter the number of copy sets with the number keys.
6. Place the originals, and then press the [Start] key.
Fold
Copies can be folded in the following ways: Z-fold, Half Fold, Letter Fold-out, Letter Fold-in, Double
Parallel Fold, and Gate Fold.
• You cannot use the bypass tray with this function.
Z-fold
Makes two parallel folds, one of which faces in and the other facing out.
3. Copy
66   
						

							To use the Z-fold function, you must set the Z-fold support tray. For details about how to set the Z-fold
support tray, see "When the Amount of Output Paper Is Less than the Stack Capacity", Troubleshooting
.
• You cannot use Punch with this function.
Original orientation and Z-fold position
Place all the originals in the ADF in the orientation in which they can be read normally. Whenplacing the original on the exposure glass, keep the same orientation, but place the original facing
downwards.
Original
orientationPlacing the original on the exposure glassPlacing the
original in the ADFDirection of fold *1Right foldBottom fold
*1
The above table shows Z-fold positions. The orientation of the paper does not indicate the orientation of
delivery.
Finishing
67CNP005           
						

							1.Press [Finishing].
2.Press [Fold].
3. Select the folding direction, and then press [OK].
4.Place the originals, and then press the [Start] key.
Half Fold
Applies a single, central fold to create two equal panels.
3. Copy
68CNP014