Ricoh Mp 2000 Service Manual

							Changing the Paper Size
75
6
DSelect [Tray Paper Settings] using {U} or {T}, and then press the {OK} key.
ESelect “Paper Size” for the paper tray of which paper size will be changed
using {U} or {T}, and then press the {OK} key.
FSelect the paper size using the scroll keys, and then press the {OK} key.
GPress the {User Tools/Counter} key.
HPull the paper tray out slowly until it stops.
IPull the end fence off from the tray.
ASB033S 
						

							Adding Paper and Replacing Toner
76
6
JPlace it in the corner pocket on the left.
KRemove any remaining copy paper.
LPress down the release button.
MWhile pressing the release lever, slide the side fences outward.
ASB020S
ASB021S 
						

							Changing the Paper Size
77
6
NPush the metal plate down until it clicks.
OSquare the paper and place it in the tray.
Be sure to set the paper under the roller.
Do not stack paper over the limit mark.
PWhile pressing the release lever, push in the side and end fences until they
are flush against the papers edges.
QPress down the lock button.
RPush the paper tray in until it stops.
SCheck the paper size on the display panel.
ASB022S
ASB026S
ASB023S 
						

							Adding Paper and Replacing Toner
78
6
Changing to a Size Other Than Indicated on the Paper Size Selector
This procedure explains how to change to a paper size not indicated on the pa-
per size selector.
ASet the paper size selector to “p”.
BPress the {User Tools/Counter} key.
CSelect [System Settings] using {U} or {T}, and then press the {OK} key.
DSelect [Tray Paper Settings] using {U} or {T}, and then press the {OK} key.
ESelect “Paper Size” for the paper tray of which paper size will be changed
using {U} or {T}, and then press the {OK} key.
FSelect the paper size using the scroll keys, and then press the {OK} key.
ASB033S 
						

							Changing the Paper Size
79
6
GPress the {User Tools/Counter} key.
HLoad the paper, and then gently push the paper tray in until it stops.
ICheck the paper size on the display panel.
Note
❒For details about the type of paper that can be loaded in Paper Tray 1, see
“Tray Paper Settings”, General Settings Guide.
Changing a Paper Size in the Optional Paper Tray Unit
This section describes how to change the size of paper loaded in the optional pa-
per tray unit.
AMake sure the paper tray is not in use.
BPull the paper tray out slowly until it stops.
CRemove any remaining copy paper.
DWhile pinching the release lever, slide the end fence outward.
ASB033S
ASB012S 
						

							Adding Paper and Replacing Toner
80
6
EPress down the release button.
FWhile pressing the release lever, slide the side fences outward.
GSquare the paper and place it in the tray.
Do not stack paper over the limit mark.
ASB014S
ASB015S
ASB013S 
						

							Changing the Paper Size
81
6
HWhile pinching the release lever, push in the side and end fences until they
are flush against the papers edges.
IPress down the lock button.
JAdjust the paper size selector in the paper tray according to the paper size.
KPush the paper tray in until it stops.
LCheck the paper size on the display panel.
Note
❒When setting small quantities of copy paper, be careful not to squeeze in
the side fence too much. Paper might not feed in properly if the side fences
are too tight against the papers edges.
❒Be sure to set the correct size, otherwise a paper jam might occur.
ASB016S
ASB024S
ASB017S 
						

							Adding Paper and Replacing Toner
82
6
Changing to a Size Other Than Indicated on the Paper Size Selector
This procedure explains how to change to a paper size not indicated on the pa-
per size selector.
ASet the paper size selector in the paper tray to “p”.
BPress the {User Tools/Counter} key.
CSelect [System Settings] using {U} or {T}, and then press the {OK} key.
DSelect [Tray Paper Settings] using {U} or {T}, and then press the {OK} key.
ESelect “Paper Size” for the paper tray of which paper size will be changed
using {U} or {T}, and then press the {OK} key.
FSelect the paper size using the scroll keys, and then press the {OK} key.
ASB033S 
						

							Changing the Paper Size
83
6
GPress the {User Tools/Counter} key.
HLoad the paper, and then gently push the paper tray until it stops.
ICheck the paper size on the display panel.
Note
❒For details about the type of paper that can be loaded in the paper tray, see
“Tray Paper Settings”, General Settings Guide.
ASB033S 
						

							Adding Paper and Replacing Toner
84
6Adding Toner
This section describes adding and storing toner.
R WARNING:
R CAUTION:
R CAUTION:
R CAUTION:
R CAUTION:
R CAUTION:
Important
❒Fault may occur if you use toner other than the recommended type.
❒When adding toner, do not turn off the operation switch. If you do, settings
will be lost.
❒Always add toner when the machine instructs you.
❒When a message “
Add toner.” is shown on the display panel, replace the
toner.
❒Store the toner bottles in a cool, dry place free from direct sunlight.
❒Store on a flat surface.
❒Do not repeatedly install and remove toner bottles. This will result in toner leakage.
❒Do not shake the removed toner bottle. Remaining toner might scatter.
Note
❒You can make about 50 copies even after the D Add Toner indicator begins
flashing, but replace toner early to prevent poor copy quality. •Do not incinerate used toner or toner containers. Toner dust might ig-
nite when exposed to an open flame. Dispose of used toner containers 
in accordance with local regulations.
Keep toner (used or unused) and toner containers out of reach of children.
If toner or used toner is inhaled, gargle with plenty of water and move into a 
fresh air environment. Consult a doctor if necessary.
If toner or used toner gets into your eyes, flush immediately with large 
amounts of water. Consult a doctor if necessary.
If toner or used toner is swallowed, dilute by drinking a large amount of wa-
ter. Consult a doctor if necessary.
Avoid getting toner on your clothes or skin when removing a paper jam or 
replacing toner. If your skin comes into contact with toner, wash the affected 
area thoroughly with soap and water.
If toner gets on your clothing, wash with cold water. Hot water will set the 
toner into the fabric and may make removing the stain impossible.