Ricoh Aficio 3025 User Manual

							x Clearing Misfeeds
129
6
ZLFX260E
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
130
6
Downloaded From ManualsPrinter.com Manuals 
						

							x Clearing Misfeeds
131
6
ZLFX270E
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
132
6Changing the Paper Size
Preparation
Be sure to select the paper size
with User Tools and the paper size
selector. If you do not, misfeeds
might occur. See p.56 “Tray Paper
Size: Tray 1–4”.
Important
❒If you want to change the paper
size set in the LCT, contact your
service representative.
Reference
For details about paper sizes and
types, see p.162 “Copy Paper”.
Changing the Paper Size of the 
Paper Tray 
AMake sure the paper tray is not in
use. Then, pull the paper tray out
slowly.
BIf paper is loaded in the tray, re-
move it.
CWhile pressing the release lever,
adjust the back guide.
DRelease the side lever.
EWhile pressing the release lever,
adjust the side guides.
FSquare the paper, and then load it
in the tray with the copying face
up.
Important
❒Do not stack paper over the lim-
it mark.
❒Make sure the paper stack is
flush against the right side
guide.
ZEWY150E
ZEWY160E
ZEWY170E
ZEWY180E
Downloaded From ManualsPrinter.com Manuals 
						

							Changing the Paper Size
133
6
Note
❒Fan the paper before loading.
❒Straighten curled or warped pa-
per before loading.
GWhile pressing the release lever,
adjust the side guides to the new
paper size.
Important
❒When loading small quantities
of paper, be careful not to
squeeze the side guide in too
tightly, as the paper will not
feed properly.
HLock the side lever.
IWhile pressing the release lever,
adjust the back guide to the new
paper size.
JAdjust the paper size selector to
the new paper size.
To adjust the paper size to a size 
not indicated on the paper size 
selector
ASet the paper size selector to
the p mark.
B
Press the {User Tools/Counter} key.
CPress [System Settings].
DPress [Tray Paper Settings].
EPress [Tray Paper Size: Tray 1],
[Tray Paper Size: Tray 2], [Tray Pa-
per Size: Tray 3] or [Tray Paper
Size: Tray 4].
FSelect the required size, and
then press [OK].
G
Press [Exit] or the {User Tools/Coun-
ter
} key to exit User Tools.
ZEWY190E
ZEWY200E
ZEWY210E
ZEWY220E
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
134
6
Reference
p.56 “Tray Paper Size: Tray
1–4”
KGently push the paper tray in un-
til it stops.
LCheck the paper size shown on
the display panel.
Downloaded From ManualsPrinter.com Manuals 
						

							d Adding Staples
135
6 d Adding Staples
Important
❒Stapling failures or jams may occur if you use a staple cartridge other than
that recommended.
Reference
For details about the type of finisher, see p.19 “External Options”.
500-Sheet Finisher
 1: Open the side cover.
 2: Remove the cartridge.
 3: Take out the empty refill in the direction 
of the arrow.
 4: Push in the new refill until it clicks.
 5: Pull out the ribbon.
ZEWJ000E
ZEWJ010E
ZEWJ020E
ZEWJ030E
ZEWJ040E
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
136
6
1000-Sheet Finisher
 6: Reinstall the cartridge.
 7: Close the side cover.
 1: Open the front cover of the finisher, and 
then pull out the staple unit.
 2: Hold the green lever, and then gently 
pull out the cartridge.
 3: Hold both sides of the cartridge.
 4: Pull up the upper unit of the cartridge.
 5: Take out the empty refill in the arrow di-
rection.
 6: Align the arrows on the new refill with 
those on the cartridge, and then push in the 
refill until it clicks.
ZEWJ050E
ZGJS801E
ZGJS802E
ZGJS803E
ZGJS804E
ZGJS805E
Downloaded From ManualsPrinter.com Manuals 
						

							d Adding Staples
137
6
 7: Gently push down the upper unit into 
the cartridge.
 8: Pull out the ribbon.
 9: Hold the green lever while pushing in 
the cartridge until it clicks.
 10: Push back the staple unit, and then 
close the front cover of the finisher.
ZGJS806E
ZGJS807E
ZGJS808E
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
138
6Removing Jammed Staples
Note
❒Curled paper may cause staples to jam. To avoid this, turn copy paper over
in the tray. If there is no improvement, change to a stiffer copy paper.
❒When the 500-sheet finisher is installed, after removing jammed staples, sta-
ples will not be ejected the first few times you try to use the stapler.
Reference
For types of finisher, see p.19 “External Options”.
500-Sheet Finisher
 1: Open the side cover.
 2: Remove the cartridge.
 3: Open the face plate.
 4: Remove the jammed staples.
 5: Reinstall the cartridge.
 6: Close the side cover.
ZEWJ000E
ZEWJ010E
ZEWJ106E
ZEWJ107E
ZEWJ108E
Downloaded From ManualsPrinter.com Manuals