Panasonic Network Camera Wv Sud638 Operating Instructions

8.5.10  Configure the VIQS areaThe VIQS area is specified by following the steps below.
1. Drag the mouse on the screen to specify the area (up to 8 areas).
→ The specified area is set to area “1(White)”, and the outline is displayed.
The areas are set in the area number order from number 1. The color next to the area number show
the color of the corresponding outline.
2. Configure the difference level in the image quality between specified areas and non-specified areas. The
greater the difference level,...

5.Click the [Confirm] button.
→ The image  (“H.264(1)”, “H.264(2)” , “H.264(3)” , or “H.264(4)” ) that the [Confirm] button was pressed for
is displayed. When a window is newly opened and about 3 seconds pass, the currently outputted bit
rate can be confirmed with the configured VIQS.
IMPORTANT
•No setting contents are determined unless the [Set] button is clicked.
• To check the image after configuring VIQS, display an H.264 image on the “Live” page, or press the
[Confirm] button under “Stream”.
• The...

8.6  Configure the settings relating to audio [Audio]Click the [Audio] tab on the “Image/Audio” page. ( ®page 32, page 34)
The settings relating to audio can be configured on this page.
Note
•Images and audio will not be synchronized. Therefore, images and audio may not always match.
• Audio may be interrupted depending on the network environment.
[Audio transmission/reception]
Select the communication mode used for audio data transmission/reception between the camera and the PC
from the following.
•...

[Audio encoding format]
Select the audio reception encoding format from G.726, G.711, AAC-LC and AAC-LC (HIGH QUALITY).
• Default:  G.726
IMPORTANT
•When “AAC-LC (HIGH QUALITY)” is selected, there are limitations about the following function.
– “Audio detection” is not available.
– HTTPS is not available.
– The maximum concurrent access number is limited to 5.
[Audio bit rate]
Select the audio bit rate used to transmit/receive audio data.
When G.726 is selected for “Audio encoding format” : 16kbps/...

•Default:  40ms
Note
•When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected,
audio interruption may be diminished even though the delay time will be longer. Select the interval
according to the network environment.
• “Mic input interval (Camera to PC)” is unavailable when “AAC-LC” or "AAC-LC (HIGH QUALITY)" is
selected for “Audio encoding format”.
[Audio output volume (PC to Camera)]
Select a volume level on the camera to hear audio transmitted...

Note•Refer to page 121 for further information about the access level.96Operating Instructions
8 Configure the settings relating to images and audio [Image/Audio] 

9   Configure the multi-screen settings
[Multi-screen]
The cameras from which images are to be displayed on a multi-screen can be registered on the
“Multi-screen” page. ( ®page 32, page 34)
[IP address]
Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be
registered as a group and up to 4 groups (16 cameras) can be registered.
When the HTTP port number for the camera of which images are to be displayed had been changed, enter as
follows:
Example of entry:...

•“Network Camera Recorder with Viewer Software Lite” which supports live monitoring and recording
images from multiple cameras is available. For further information, refer to our website
(http://security.panasonic.com/support/info/).
• This camera is specified when “selfcamera” is displayed for the IP address or host name.
Note
•When using the host name, it is necessary to configure the DNS settings of the PC to be used for the
multi-screen display. Refer to the network administrator for information on...

10   Configure the alarm settings [Alarm]The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence or
alarm images, the VMD area settings, audio detection settings, and the alarm occurrence notification can be
configured on this page.
The “Alarm”  page has the [ Alarm] tab, the [ VMD area ] tab, the [Audio detection ] tab, and the [Notification] tab.
10.1  Configure the settings relating to the alarm
action [Alarm] Click the [Alarm] tab on the “Alarm” page. (...

[Terminal 2]
Determine how to use terminal 2.
• Off:  Not used.
• Alarm input:  Receives alarms. When “Alarm input” is selected, a pull-down menu for “Close” and
“Open” is displayed.
– Close:  An alarm is detected when the terminal status is changed to “Close”.
– Open:  An alarm is detected when the terminal status is changed to “Open”.
• Alarm output:  Alarm output will be carried out according to the settings for “Alarm output terminal
setup” ( ®page 108).
• Default:  Off
[Terminal 3]
Determine how to...