Panasonic Network Camera Wv Sud638 Operating Instructions

IMPORTANT•The mask area may move out of alignment when the JPEG/H.264 “Image capture mode” setting is
changed. Make sure to check the mask area after changing the “Image capture mode” setting.
• The mask area may move out of alignment when  “HD Extra optical zoom ” is configured. Make sure to
check the mask area after configuring “HD Extra optical zoom”.
Note
•When the [Reset] button is clicked, masking for all the masked areas will be canceled.
8.5.3  Configure the settings relating to the preset...

IMPORTANT•When the zoom factor is 45x or more, the setting of the preset positions will become unavailable.
• Preset position can be set to a maximum of 256 positions.
Note
•Depending on the environment  (such as when the temperature is below 5 ° C  (41  °F), for example), the
moving speed of the camera to the preset position may become slower.
• Reconfigure the preset position if the way the camera is fixed is changed after registering preset
positions.
72Operating Instructions
8 Configure the settings...

Position No[Preset ID]
Select  “On” or “Off”  to determine whether to enable or disable the preset ID display. This function can be applied
to each preset position.
• On:  Displays the preset ID.
• Off:  Does not display the preset ID.
• Default : Off
IMPORTANT
•When  “Preset ID  (0-9,A-Z)” or “Preset ID ” is configured, it is necessary to click the [ Set] button to apply
them.
Note
•When “On” is selected, the entered preset ID will be displayed at the position selected for “OSD” on
the [Basic] tab of...

•On:  The Super Dynamic function will work.
• Off:  The Super Dynamic function will not work.
• Default:  Off
[Back light compensation (BLC)]
Select “On”  or “Off”  to determine whether or not to activate the back light compensation  (BLC) function. When
“On” is selected for “Super Dynamic”, this setting is unavailable. The back light compensation function can
compensate back light by setting mask areas on brighter parts of images.
• On:  Mask areas will be set automatically.
• Off:  Mask areas will not...

8.5.4  Configure the settings relating to the auto pan function
(“Auto pan” setup menu)
Click the [Setup>>] button of “Auto pan” on the [Image/Position] tab of the “Image/Audio” page ( ®page 58).
The settings relating to the auto pan function can be configured with the setup menu.
Position
[Left end position setup]
Move the camera to the desired point to be set as the left end position point of the auto panning using the
control pad/buttons and adjust the image using the [Zoom] buttons and the [Focus]...

Note•Panning, tilting and zooming operations can also be carried out on the [Image/Position] tab.
• Adjusted zoom and focus position for the auto pan function will be applied when the [Set] button is
clicked.
Auto pan [Dwell time]
Select a dwell time at the start point and the end point from the following.
0s/ 1s/ 2s/ 3s/ 4s/ 5s/ 10s/ 15s/ 20s/ 25s/ 30s
• Default:  5s
[Speed]
Select a speed for the auto panning from the following.
1°/s, 2°/s, 3°/s, 4°/s, 5°/s, 7°/s, 10°/s, 13°/s, 18°/s, 24°/s
• Default:...

The Patrol function can be configured to learn pan, tilt, zoom, focus, and brightness settings and operations,
and then use these learned settings and operations to operate the camera.
Patrol setting
[Number of patrol pattern]
Select the patrol pattern number. The length of patrol patterns that can be learned differs depending on the
pattern number.
• 1: 2 minutes of operations can be learned for Patrol 1.
• 2: 1 minute of operations can be learned for both Patrol 1 and Patrol 2.
• 4: 30 seconds of...

Note•The following are the camera operations that can be learned.
– Start position operations
pan/tilt/zoom/focus position/brightness
– Camera operations
pan/tilt/zoom/focus position/brightness/moving the preset position
• The auto focus function cannot be used when performing patrol operations. As a characteristic of zoom
lenses, when images are zoomed up from the “Wide” side, they may become blurred. When learning
zoom operations, starting from the “Tele” side will reduce blurring.
[Zoom] buttons,...

The Auto track function can be used to detect movement in a predetermined area and automatically track and
capture images of the subject detected in that area.Operating Instructions79
8 Configure the settings relating to images and audio [Image/Audio]   

Auto track setting[Camera height]
Select the height that the camera is installed to from the following.
2.5m(8.5ft)/2.75m(9.0ft)/3.0m(10.0ft)/3.25m(11.0ft)/3.5m(11.5ft)/3.75m(12.5ft)/4.0m(13.5ft)/4.25m(14.0ft)/
4.5m(15.0ft)/4.75m(16.0ft)/5.0m(16.5ft)/5.5m(18.5ft)/6.0m(20.0ft)/6.5m(21.5ft)/7.0m(23.5ft)/7.5m(25.0ft)/
8.0m(26.5ft)/8.5m(28.5ft)/9.0m(30.0ft)/9.5m(31.5ft)/10.0m(33.5ft)/12.0m(40.0ft)/14.0m(46.5ft)/16.0m(53.5ft)/...