Panasonic Network Camera Wv Sud638 Operating Instructions

Advanced setting[Zoom with auto track]
Select the tracking zoom control from the following.
Off:  Zoom control is not performed.
On:  Zoom control is performed.
Default:  On
[Object size]
Select an object size from the following.
Small(1/4 of the image):  The tracking target is enlarged to about 1/4 the size (lengthwise) of the monitor
screen.
Middle(1/2 of the image):  The tracking target is enlarged to about 1/2 the size (lengthwise) of the monitor
screen.
Large(3/4 of the image):  The tracking target...

Alarm area[Area select]
Click [
] of “Area No.” and select an area number (1-4) from the pull-down menu. An asterisk (*) next to the
area number indicates that the area has already been learned. When “On” (when there is an alarm area
intrusion) is selected with “Auto track alarm”, the alarm area will become active.
[Area No. notification]
When “Panasonic alarm protocol notification >>” is clicked, the [Notification] tab of the “Alarm” page will be
displayed. ( ®page 117)
Note
•The alarm area cannot be...

–when the target moves too fast or too slow
– when the camera is shaking
• In no event shall we be liable to any consequential inconvenience, or loss or damage, arising out of
the settings or results of the Auto tracking system.
• We recommend that you use this setting under the following setting conditions to improve the detection
accuracy.
– set the size of the tracking target to over 1/5 of the monitoring screen (lengthwise)
Procedure to setup auto track cooperation If 2 or more cameras that support...

4.Configure the settings of Camera 2  (IP address:  192.168.0.12 ), which receives notification commands from
the other cameras.
Display the “Alarm” screen from the “Alarm” page. ( ®page 99)
From “Alarm”, set “Command alarm” to “On” and click the [Set] button.
Set the “Command alarm” of “Camera action on alarm” to “Preset per sender”, and click “Preset per
sender >>”.
On the “Preset per sender” setup menu ( ®page 103), check the “Auto track cooperation” checkbox
of “Sender's address 1” ( any...

[Panning 0° direction setting]
Configure the Panning 0° direction setting. When the [Set] button is clicked after adjusting the angle of view
with the control pad/buttons, the current direction of the pan becomes 0°. Click the [Reset] button to reset to
the default setting.
Note
•The tilt 0° angle is not configured.
• Even if the Panning 0° direction is changed, there is no change to the preset positions already
configured. The range of the auto pan setting and the actions of the patrol setting already...

•Reconfigure the privacy zone if the way the camera is fixed is changed.
Zone setting
[Zone select]
Click [
] of “Zone No” and select a zone number (1-8 or 1-32) from the pull-down menu.
An asterisk (*) next to the zone number indicates that the privacy zone has already been set for the number.
The privacy zone will be set when an area is designated by dragging the mouse.
Click the [Set ] button after determining the position of the camera. In this case, a slightly wider area than was
specified will be...

[Close] button
Click this button to close the “Privacy zone” setup menu.Operating Instructions87
8 Configure the settings relating to images and audio [Image/Audio] 

8.5.9  Configure the VIQS settingClick the [Setup>>] button of “VIQS” on the [Image/Position] tab of the “Image/Audio” page. ( ®page 58)
VIQS is an abbreviation of Variable Image Quality on Specified area and is a feature that enables you to change
the images of a specified area.
It is possible to enhance the image quality of the specified range within a shooting area (image).
It is also possible to moderate the image data size by lowering the image quality of other areas.
The VIQS setting is available...

In order to configure a VIQS area outside of preset areas, select “except the preset positions”.
[Area]
When selecting a VIQS area in the screen, it will be numbered as area 1.  (Subsequent areas will be numbered
in the order of selection.)
[Center]
When the [Center] button is clicked, the whole area will become the VIQS area, and “1(White)” will be
automatically applied to “Area”.
[Status]
Select “On” or “Off” to determine whether or not to use the VIQS area.
• On:  The VIQS area will be set.
• Off:...

[Level]
Configure the difference level in the image quality between specified areas and non-specified areas. The
greater the difference level, the more the image quality of the non-specified area is reduced. This makes it
possible to moderate the image data size.
0 Min./ 1/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Max.
• Default:  5 Normal90Operating Instructions
8 Configure the settings relating to images and audio [Image/Audio]