Panasonic Network Camera Wv Sud638 Operating Instructions

[Super Dynamic(SD)]
Select “On”, or “Off” to determine whether or not to activate the super dynamic function.
The super dynamic function cannot be selected when  “2 mega pixel [16:9] (60fps mode) ” is selected for  “Image
capture mode”.
Refer to the description “Super Dynamic function” ( ®page 61) about the super dynamic function.
• On:  The super dynamic function will work.
• Off:  The super dynamic function will not work.
• Default:  Off
Note
•When the following are observed depending on the light...

Select “On” or “Off” to determine whether or not to interact with the Super Dynamic function.
• On:  The interactive control with face detection will work.
• Off:  The interactive control with face detection will not work.
• Default:  Off
Note
•The interactive control with face detection is available even when “Off” is selected for “Super
Dynamic(SD)”. In the image quality settings of each preset position, face detection is applied when
“On” is selected for “Super Dynamic(SD)”.
[Adaptive black stretch]...

Note•When a faster shutter speed is selected (up to 1/10000 Fix), it is possible to capture a fast moving
object with less blur.
• When a faster shutter speed is selected, the sensitivity will become lower.
• When “On” is selected for “Super Dynamic(SD)”, “Fix shutter” is not available.
To configure “Fix shutter”, set “Super Dynamic(SD)” to “Off”.
• When “Fix shutter” is used, if there is fine weather (about 60,000 lx or more), subjects may be
overexposed.
When there is overexposure, increasing the...

Super Chroma Compensation (SCC)
This function achieves faithful color images using the proprietary color compensation technology that
reproduce images even under low illumination where it is usually difficult to capture objects faithfully.
Note
•The operating sound might be heard when changing to black-and-white mode, however it does not
indicate any malfunction.
• Since the color compensation technology is used for Auto3(Super Chrome Compensation(SCC)),
some colors may look different from the actual...

–When shooting a subject whose luminance is too low
• When “AWC” is selected, click the [Set] button.
[Red gain]
Adjust the red color of images.
When the cursor is moved in the “+”  direction, the red color will become thicker. When the cursor is moved in
the “-” direction, the red color will be thinner. Click the [Reset] button to reset the color to the default.
• Default:  128
[Blue gain]
Adjust the blue color of images.
When the cursor is moved in the “+” direction, the blue color will become thicker....

Pan/tilt stabilization reduces the distortions in images. This is effective with correcting large, slow-moving
distortions.
IMPORTANT
•If “Stabilizer” is used, the view angle will become narrower and the resolution becomes lower. In
this case, check the view angle and resolution at camera installation. The image stabilizer function
may become less effective under the following conditions.
– Short cycled image shaking such as mechanical vibration
– Large amplitude image shaking
• If “Stabilizer” is used,...

When the cursor is moved to the “+” direction, images will become brighter. When the cursor is moved to the
“-” direction, images will be darker. Click the [Reset] button to reset the color to the default.
• Default:  128
[Fog compensation]
Select “On” or “Off” to determine whether or not to activate the fog compensation function. When “On” is
selected for “Super Dynamic(SD)”, or when “On” is selected for “Adaptive black stretch”, this setting is not
available.
The fog compensation function can make dim...

[Close] button
Click this button to quit the “Image adjust” setup menu.
8.5.2  Set mask areas When “Off” is selected for “Super Dynamic(SD)” and “Back light compensation (BLC)”, it is possible to
compensate for backlight by masking brighter areas.68Operating Instructions
8 Configure the settings relating to images and audio [Image/Audio] 

1.Display the “Image adjust” setup menu. ( ®page 58)Operating Instructions69
8 Configure the settings relating to images and audio [Image/Audio]   

2.Click the [Start] button of “Mask area”.
→ Borders will appear and the image displayed on the [Image/Position] tab will be divided into 48 (6x8).
3.Click the divided areas to be masked.
→ The clicked areas will be masked and will become white. To cancel masking, click the area again.
4.Click the [End] button after completing masking areas.
→ The borders on the image displayed on the [Image/Position] tab will disappear.
70Operating Instructions
8 Configure the settings relating to images and audio...