Panasonic Network Camera Wv Sud638 Operating Instructions

•[3] button:  The letter “3” will turn green and images in the main area will be displayed in accordance
with the setting of “H.264(3)”. ( ®page 49)
• [4] button:  The letter “4” will turn green and images in the main area will be displayed in accordance
with the setting of “H.264(4)”. ( ®page 49)
[Image capture size] buttons
These buttons will be displayed only when a JPEG image is displayed.
Aspect ratio of
“4:3”[1280x960]The letters “1280x960” will turn green and images in the
main area will be...

2.The washer operates according to the “Pulse width” setting. ( ®page 43)
3. While wiping according to the  “Wiper count ” setting  (® page  43), the camera moves back to its original
position.
Note
•During washer operations, wiper [ Start] and [Stop], pan/tilt/zoom/focus control, Auto mode [ Start],
and preset action [Start] cannot be operated.
• “Washer” can only be selected when “Washer control” is selected for “Relay output” on the
[Basic] tab of the “Basic” page. Refer to page 43 for information on...

–Inclined subject
– Dark subjects
Auto mode *2
Select an operation from the pull -down menu and click the [ Start] button. The selected operation will start.
Click the [Stop] button to stop the operation. The selected operation will stop when the camera (panning/
tilting/zooming/focusing) is operated or when an action that is to be taken according to the settings for  “Self
return”( ®page 55) or for “Camera action on alarm” ( ®page 101) starts.
Note
•The [ Start] button for  “Auto mode ” cannot be...

•When “360 map-shot”  is carried out while the camera is moving  (panning/tilting), images captured
while panning/tilting may be displayed as the thumbnail display. In this case, stop the current
operation and carry out “360 map-shot” again.
• When  “Preset map -shot” is carried out with an unregistered preset position  (among preset position
1-8), the thumbnail image of the preset position before the unregistered preset position will be
displayed.
In this case, the camera will not move when the...

Note•Since the blinking of the alarm occurrence indication button is not coupled to forwarding E-mails,
or other operations, check the settings of each operation separately.
Full screen button
Images will be displayed on a full screen. If the full screen button is clicked once when the image displayed
in the main area is smaller than the main area, the image is displayed corresponding to its image capture
size. If the full screen button is clicked once when images are displayed corresponding to their...

•The duration of continuous audio transmission can be configured in the [Audio] tab of the setup
menu. Audio output stops when the specified time has passed. To turn the audio transmission
function on, click the [Audio output] button again.
• When the camera is restarted, the adjusted volume level (for both the audio transmission and
reception) will return to the level that had been set on the [Audio] tab on the setup menu.
( ® page 93)
• Actual volume level will change in three steps even though the...

1.3  Monitor images from multiple camerasImages from multiple cameras can be displayed on a multi -screen. Images from 4 cameras  (up to 16 cameras)
can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in
advance. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered.
( ® page 97)
IMPORTANT
•When displaying images on a 16 -screen, panning, tilting and zooming operations become unavailable
for images from cameras with...

2   Monitor images on a cellular phone/mobile
terminal
2.1  Monitor images on a cellular phone It is possible to connect to the camera using a cellular phone via the Internet and monitor images  (JPEG only)
from the camera on the screen of the cellular phone. It is also possible to refresh images to display the latest
image.
IMPORTANT
•When the authentication window is displayed, enter the user name and password.
To enhance the security, change the password periodically. ( ®page 121)
• If the cellular...

1.Access to “http://IP address/mobile” *1
 or “http://Host name registered in the DDNS server/mobile” using a
cellular phone.
→ Images from the camera will be displayed.
Pan/Tilt *2
Controls the camera direction. The camera will pan or tilt to each direction by pressing the
corresponding dial key.
Zoom display *2
It is possible to perform zooming operations of the camera by pressing “*” or “#”.
Refresh control
Press the dial key “5” or the [Manual Refresh] button to refresh the camera images.
Press the...

Resolution control
Changes the image capture size by pressing the dial key “0”.
• Image in the aspect ratio of  “4:3”: Changes the image capture size between  320x240 ( default) and
640x480.
• Image in the aspect ratio of “16:9”: Changes the image capture size between 320x180 (default)
and 640x360.
Image quality control
It is possible to change the image quality between “Quality1” and “Quality2”. ( ®page 47)
Home position *2
The camera will move to the home position. ( ®page 55)
Home position will be...