Panasonic Network Camera Wv Sud638 Operating Instructions

12.2.1  Configure the settings related to sending E-mails
[E-mail notification]
Select “On” or “Off” to determine whether or not to provide notification by E-mail.
• Default:  Off
[Alarm image attachment]
Select “On” or “Off” to determine whether or not to attach an image to the E-mail to be sent when an alarm is
detected.
• Default:  Off
[Image capture size]
Select the image capture size of images attached to an alarm E-mail from the following.
JPEG(1)/JPEG(2)/JPEG(3)
• Default:  JPEG(2)
[SMTP server...

•Available characters:  Alphanumeric characters, the colon (:), the period (.), the underscore (_), and the
hyphen (-).
[SMTP port]
Enter the port number to which E-mails are sent.
• Available port number:  1-65535
• Default:  25
The following port numbers are unavailable since they are already in use.
20, 21, 23, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 995, 10669, 10670
[POP server address]
When “POP before SMTP” is selected for “Type”, enter the IP address or the host name of the POP server.
•...

Note•Some SMTP servers may not support SSL.
• SSL supports SMTP over SSL, but STARTTLS is not supported.
• When “On” is selected, the SMTP port number may need to be set to 465. Ask your Internet service
provider for the appropriate settings.
[Address 1] - [Address 4]
Enter the destination E-mail address. Up to 4 destination E-mail addresses can be registered.
• [Alarm ] checkbox:  When the checkbox is selected, the E -mail notification will be performed upon an alarm
occurrence.
• [Destination E-mail...

12.2.2  Configure the settings related to FTP transmission
FTP[Alarm image FTP transmission]
Select “On” or “Off” to determine whether or not to transmit the alarm image to the FTP server.
• Default:  Off
[Directory name]
Enter the directory name where the alarm images are to be saved.
For example, enter “/ALARM” to designate the directory “ALARM” under the root directory of the FTP server.
• Available number of characters:  1 - 256 characters
• Unavailable characters:  " & ;
[File name]
Enter the...

•Available number of characters:  1 - 32 characters
• Unavailable characters:  " & * / : ; < > ? \ |
[FTP transmission retry]
Select “On” or “Off” to determine whether or not to resend failed FTP transmissions.
• On:  If transmission fails, transmissions are resent until they are successfully sent.
• Off:  If transmission fails, the image that failed to be sent is discarded and the next image is sent.
• Default:  Off
[Pre alarm]
• Transmission interval
Select the update interval of images before an...

[Post alarm]
• Transmission interval
Select the transmission interval for the alarm image transmission to the FTP server from the following.
0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps
• Default:  1fps
• Number of images
Select the number of images to be transmitted from the following.
1pic/ 2pics/ 3pics/ 4pics/ 5pics/ 6pics/ 7pics/ 8pics/ 9pics/ 10pics/ 20pics/ 30pics/ 50pics/  100pics/ 200pics/
300pics/ 500pics/ 1000pics/ 1500pics/ 2000pics/ 3000pics
• Default:  100pics
• Recording duration
Approximate time...

[Transmission interval]
Select the interval for the FTP periodic image transmission from the following.
1s/ 2s/ 3s/ 4s/ 5s/ 6s/ 10s/ 15s/ 20s/ 30s/ 1min/ 2min/ 3min/ 4min/ 5min/ 6min/ 10min/ 15min/ 20min/ 30min/
1h/ 1.5h/ 2h/ 3h/ 4h/ 6h/ 12h/ 24h
• Default:  1s
[Image capture size]
Select the image capture size of images to be transmitted from the following.
JPEG(1)/JPEG(2)/JPEG(3)
• Default:  JPEG(2)
[FTP server address]
Enter the IP address or the host name of the FTP server.
• Available number of...

IMPORTANT•Use an NTP server when the more accurate time & date setting is required for the system operation.
[Time adjustment]
Select the time adjustment method from the following. Time adjusted by the selected method will be used as
the standard time of the camera.
• Manual:  Time set on the [ Basic] tab on the “Basic”  page will be used as the standard time of the camera.
• Synchronization with NTP server:  Time automatically adjusted by synchronizing with the NTP server
will be used as the standard...

The following port numbers are unavailable since they are already in use.
20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 161, 162, 443, 995, 10669, 10670
[Time adjustment interval]
Select an interval (1 - 24 hours: in 1 hour intervals) of synchronization with the NTP server.
• Default:  1h
12.2.4  Configure the UPnP settings This camera support UPnP (Universal Plug and Play). By using the UPnP function, it becomes possible to
configure the following automatically.
– Configuration of the port forwarding...

[Start] ®  [Control Panel]  ® [Network and Internet]  ® [Network and Sharing Center ] ®  select [ Turn on
network discovery] of [Network discovery] of [Change advanced sharing settings]  ® click [Save
changes]  ® Complete
For Windows 8.1 and Windows 8
Right-click [Start]  ® select [Control Panel]  ® [Network and Internet]  ® [Network and Sharing Center ]
®  select [Turn on network discovery] of [Network discovery] of [Change advanced sharing settings]
®  click [Save changes]  ® Complete
For Windows 10...