Panasonic Matrix Switcher Wj Sx150a Operating Instructions

104
LOG-IN AND LOG-OUT
Before starting the following procedures, all system compo-
nents must be turned on.
The following procedures are applicable when the system
controller is connected to the unit.
■ Log-in
This operation is skipped when the auto log-in is set to ON.
(Refer to p. 92.)
1. Turn on the power switches of all system components. 
The OPERATE indicator will light up.
2. To turn on the power of the system controller, connect
the AC adapter to the AC outlet.
The LINK indicator lights up and NO...

105
■ Log-out
This operation is skipped when the auto log-out is set to
ON. 
This function is used when an operator leaves the controller
or no longer requires access to the system.
1. To logout from the system press the CLEAR button
while holding down the SHIFT button.
NO USER appears on the LED display of the con-
troller.
Notes:
•If you want to save the power consumption, discon-
nect the PC plug from the controller, and remove
the AC adapter from the AC outlet.
•If the auto log-out is set to ON, any...

106
■ Priority Lock
● Applying Priority Lock
1. Select the desired monitor. (Refer to Monitor Selection).
2. Press the MON (ESC) button while holding down the
SHIFT button to toggle the priority lock mode on and off
on the active monitor.
If the priority lock mode is selected, the monitor number
will inversely appear on the active monitor as shown in
the figure.
Note:This function will prevent operators with lower priority
from gaining control of a monitor.
However, higher or equal priority operators may...

107
■ Camera Selection
1. Select the desired monitor. (Refer to p. 106 Monitor
Selection.)
2. Press the numeric buttons to select the desired camera
number (1 to 99).
3. Press the CAM (SET) button.
The selected cameras image will appear on the active
monitor. The CAMERA indicator will light up and the
selected camera number will appear on the LED dis-
play on the controller.
SETUP
SHIFT
REW/FF
STEP
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
RECORDER
INDEX
STOP...

108
Buttons and control for cameras or camera site accessories
are located on the right side of the front panel of the system
controller.
Included are zoom control, focus control, iris control, preset
and pan/tilt controls. 
Normally, combination cameras equipped with the specific
feature or a WV-RC100 or WV-RC150 Receiver are required
to utilize these functions.
Note:Refer to the cameras operating instructions whether
to confirm that each function is available.
■ Lens Control
This function is available...

109
■ Call Preset Position
1. Select the desired monitor and camera. (Refer to p. 106
Monitor Selection and p. 107 Camera Selection.)
2. To select the desired preset position number, press the
numeric buttons. (1 to 64)
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the CALL PRESET button to move to the preset
position of the selected camera on the active monitor.
■ Program Preset Position
1. Select the desired monitor and camera. (Refer to p. 106...

110
■ Camera Function (Shortcut
Function)
The following function is available only when specified cam-
eras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera. (Refer to p. 106
Monitor Selection and p. 107 Camera Selection.)
2. Press the AUTO PAN button while holding down the
SHIFT button.
F_ _ _ _  will appear on the LED display of the con-
troller as shown in the figure.
■ Camera Setup
1. Select the...

111
■ Patrol Learn and Play
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera. (Refer to p. 106
Monitor Selection and p. 107 Camera Selection.)
2. Press the AUTO PAN button three times while holding
down the SHIFT button.
LEARN will appear on the LED display of the controller
as shown in the figure.
■ Changing to Black and White
Images
This function gets the clear camera images on the monitor
while shooting the...

112
■ Camera Panning Function
There are three panning modes available as follows: auto
pan, sort mode and sequence mode. Refer to p. 16
Camera-related Functions for details on each mode.
1. Select the desired monitor and camera. (Refer to p. 106
Monitor Selection and p. 107 Camera Selection.)
2. Press the AUTO PAN button four times while holding
down the SHIFT button.
PAN will appear on the LED display of the controller as
shown in the figure.4. To exit from the mode, press the MON (ESC) button,
then...

113
■ Receiver Control
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
● Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 106
Monitor Selection and p. 107 Camera Selection.)
2. Press the CAM (SET) button while holding down the
SHIFT button to turn on the housing wiper of the camera
until buttons are released.
Defroster Control
1. Select the desired monitor and camera. (Refer...