Panasonic Matrix Switcher Wj Sx150a Operating Instructions

145
This section will describe what you should take notice when using a PS·Data system controller.
The same descriptions as the system controller’s operating instructions are not mentioned here. Refer to them.
Notes:
•Before the use, it is necessary to install the Multiplexer board in the matrix switcher, connect the matrix switcher to the
time-lapse VCR, and configure the system through WJ-SX150A Administrator Console, OSD SETUP MENU, and time-lapse
VCRs SETUP MENU. [Refer to p. 32 Installing the...

146
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (PS·DATA)MUX
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Notes:
•The same descriptions as the system controller’s
operating instructions are not mentioned here. Refer
to them.
•Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure the system through WJ-SX150A
Administrator Console, OSD SETUP MENU,...

147
MONITOR DISPLAY WHEN A VIDEO LOSS OCCURS
■Video Loss Display
•When video loss of CAMERA IN nn (nn is a number) is
detected,  LOSS CH nn will blink on the monitor.
•When more than one LOSS CH have occurred, LOSS
CH nn* will appear on the monitor.
•When the input loss is recovered, LOSS CH nn will dis-
appear from the monitor.
•When you press the RESET button while pressing the
OSDbutton, LOSS CH nn will disappear from the
monitor.
■Camera Switching Pulse Loss
Display 
•When loss of the camera...

148
TROUBLESHOOTING
Check to see the following before request for repair.
If a trouble cannot be removed even after checking and trying remedy, contact your dealer.
Problem Check item Remedy
Matrix switcher does not power up. The power cord may be disconnected
either from the units power socket or
the AC outlet.Connect the power cord between the
unit
s power socket and the AC outlet.
System controller(s) do (does) not log
in.The unit’s power cord may be discon-
nected from the AC outlet.Connect the power...

149
The camera image is dim. Dust may be sticking on the camera
lens.Remove the dust from the camera lens. 
The camera’s lens focus may not be
proper.Press the FOCUS NEAR/ FAR buttons to
adjust the lens focus. If the camera sup-
ports auto focus, press these buttons
simultaneously. The lens focus can be
adjusted automatically.
The camera’s cable compensation set-
ting may not be proper.Open 730 COMPENSATION/VD2/DATA
(refer to p. 74) or the Cable Compensa-
tion/VD2 window (refer to p. 94) to con-
firm the...

150
“Initializing…” is displayed on monitors.
(For WJ-HD500 Series recorders) You
cannot search for records even when car-
rying out the Search Playback procedure.
Recording or playback with the recorder
is not correctly carried out. “NOT ASSIGN” is displayed beside the
camera number on the monitor.The alarm mode is not activated.
The alarm mode is set to OFF. Set the alarm mode to SEQUENCE or
HOLD in SETUP MENU or WJ-SX150A
Administrator Console.
SETUP MENU: Refer to p. 67.
Administrator Console: Refer...

151
APPENDIX 

152
[STX]   [Response Command] : [E] [R] [n1] [n2] [n3] [ETX] Parameters are omitted when the command format includes neither data nor status to send back.
(2) Reception Error
The unit sends back NAK code 15H, followed by the parameters. The unit then resets the reception buffer and enters the
waiting mode for the next message. Parameter e identifies the error status. [p] stands for parameter. Parameters are omitted when the command does not need to specify them.
2. Response Command
The unit returns...

153
ANS:H00SGn
mm=Monitor No.
n=0 (SEQUENCE), 1 (PAUSE) ANS:HmmSPn Pausing sequence
(PAUSE)
Stopping sequence
(STOP)
Sequence increment
(NEXT)
Sequence decrement
(PREV)
Transmission command toggles priority lock
ON or OFF.
mm=Monitor No.
n=0 (OFF)
n=1 (ON) Starting tour sequence
■Command Table
Item Response (ASCII) Parameter (ASCII)
Log-in CMD:Wnnnnn-ppppp ANS:WOK (When OK)
ANS:WNG (When NG)nnnnn= Operator number
ppppp= Password
Log-out CMD:H00LG ANS:H00LG
Monitor Selection CMD:HmmMS ANS:HmmMSmm=Monitor...

154
Transmission command toggles alarm sus-
pension ON or OFF.
n=0  OFF
n=1  ON Alarm ACK
(Each monitor)CMD:HmmAK ANS:HmmAKmm=Monitor No. Item
Alarm input OAIcc No responsecc=Alarm No. Transmission Command
(ASCII)Response (ASCII) Parameter (ASCII)
Alarm reset
(Each monitor)CMD:HmmAR ANS:HmmARmm=Monitor No.
Alarm all reset CMD:H00AR ANS:H00AR
Alarm suspension MAD madn
Alarm Control
Return to normal view* CMD:HmmSE ANS:HmmSEmm=Monitor No.
*Available only in SETUP MENU Item
Display SETUP MENU CMD:HmmSS...