Panasonic Matrix Switcher Wj Sx150a Operating Instructions

135
WJ-HD200 SERIES CONTROL (TERMINAL MODE)
Matrix switcher can control Digital Disk Recorder WJ-
HD200 Series. The following is the procedure of WJ-HD200
Series SETUP MENU.
Notes:
•The following operating procedures are for the terminal
mode. If you are using a PS·Data system controller,
refer to p. 143.
•When a Multiplexer board is installed in the unit, you
can neither connect nor control a WJ-HD200 Series
recorder. You need to remove the board from the unit.
■Displaying WJ-HD200 Series
SETUP MENU
The...

136
3. Press the numeric buttons or NEXT/PREV button to
enter the desired date and time.
The cursor can be adjusted by moving the joystick
rightward or leftward.
4. Press the PLAY button. After the search through the
date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the CLEAR button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
Move the cursor with the...

137
WJ-HD100 SERIES CONTROL  (TERMINAL MODE)MUX
Digital Disk Recorder WJ-HD100 Series are operable with
the system controller, when the Multiplexer board is
installed in the unit.
Note:Before the use, it is necessary to install the Multi-
plexer board in the matrix switcher, connect the
matrix switcher to the digital disk recorder, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and WJ-HD100 Series
SETUP MENU. [Refer to p. 32 Installing the
Multiplexer Board, p. 45...

138
3. Press the numeric buttons or NEXT/PREV button to
enter the desired date and time. The cursor can be
adjusted by moving the joystick rightward or leftward.
4. Press the PLAY button. After the search through the
date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the CLEAR button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
Move the cursor with the...

139
TIME-LAPSE VCR CONTROL  [PANASONIC MODELS] (TERMINAL MODE)MUX
A time-lapse VCR (Panasonic Models) is operable with the
system controller, while connecting to the matrix switcher.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the time-lapse VCR, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and time-lapse VCRs
SETUP MENU. [Refer to p. 32 Installing the
Multiplexer Board, p. 46...

140
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (TERMINAL MODE)MUX
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Notes:
•Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure the system through WJ-SX150A
Administrator Console, OSD SETUP MENU, and
time-lapse VCRs SETUP MENU. [Refer to p. 32
Installing the Multiplexer Board, p. 47 Connection
with...

141
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
■Controlling the Recorder with a PS·Data System Controller
●Recorder Mode
Before operating the recorder, it is necessary to enter the recorder mode.
1. Select the desired monitor. (Refer to p. 125 Monitor Selection.)
2. In the PS·Data mode, a number is assigned to each recorder. To select a desired...

142
●Stopping REC ONLY Alarm Recording
You can stop alarm recording activated by “REC ONLY” setting of 430 CAMERA/440 ALARM PORT/450 SERIAL PORT/460
MUX MOTION DET in SETUP MENU (refer to pp. 68 and 69) or the Alarm Mode window in WJ-SX150A Administrator Console
(refer to p. 88).
To stop the alarm recording, press the ALM RESET button. 

143
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
■Controlling the Recorder with a PS·Data System Controller
1. Enter the recorder mode. (Refer to p. 141.)
2. Press the SHIFT button to activate the FUNCTION buttons.
3. Enter the desired function code, and then press the FUNCTION button. (Refer to the diagram.)
4. To select a camera channel, press...

144
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
Note:Before the use, it is necessary to install the Multiplexer board in the matrix switcher, connect the matrix switcher to the
digital disk recorder, and configure the system through WJ-SX150A Administrator Console, OSD SETUP MENU, and WJ-
HD100 Series SETUP MENU. [Refer to p. 32 Installing the...