Panasonic Matrix Switcher Wj Sx150a Operating Instructions

							135
WJ-HD200 SERIES CONTROL (TERMINAL MODE)
Matrix switcher can control Digital Disk Recorder WJ-
HD200 Series. The following is the procedure of WJ-HD200
Series SETUP MENU.
Notes:
•The following operating procedures are for the terminal
mode. If you are using a PS·Data system controller,
refer to p. 143.
•When a Multiplexer board is installed in the unit, you
can neither connect nor control a WJ-HD200 Series
recorder. You need to remove the board from the unit.
■Displaying WJ-HD200 Series
SETUP MENU
The operations are the same as WJ-HD500 Series. (Refer to
p. 130.)
■Controlling Digital Disk
Recorder WJ-HD200 Series
The following are the operating procedures of WJ-HD200
Series via system controller.
Note: Refer to the operating instructions of Digital Disk
Recorder WJ-HD200 Series for details.
●Recorder Mode
The operations are the same as WJ-HD500 Series. (Refer to
p. 131.)
●Multiscreen Segment Switching
The operations are the same as WJ-HD500 Series. (Refer to
p. 131.)
Note:4C-, 4D-, 7-, 10-, 13- and 16-segment multiscreen
display are unavailable.
●Normal Playback
The operations are the same as WJ-HD500 Series. (Refer to
p. 131.)
Note:You cannot skip to the previous/next record.
●Manual Recording
The operations are the same as WJ-HD500 Series. (Refer to
p. 132.)
Note:Refer to WJ-HD200 Series Operating Instructions for
details and other recording modes. 
●Stopping REC ONLY Alarm
Recording
The operations are the same as WJ-HD500 Series. (Refer to
p. 132.)
●Search Playback
You can search playback images using the ALARM
RECALL table or the SEARCH table.
Every time you press the INDEX button, the display will
change as follows.
Live image →Date-and-time entry form →ALARM RECALL
table →Live image
• Date-and-time Search Playback
The recorded images can be searched for through the date
and time.
1. Enter the recorder mode. (Refer to p. 131 Recorder
Mode.)
2. Press the INDEX button. The date-and-time entry form
will appear on the center of the monitor.
Note:The factory default setting is the current date and
time.
F2
INDEX
                 SEARCH
            YYYY/MM/DD HH:MM
            2002/05/07 19:32 
						

							136
3. Press the numeric buttons or NEXT/PREV button to
enter the desired date and time.
The cursor can be adjusted by moving the joystick
rightward or leftward.
4. Press the PLAY button. After the search through the
date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the CLEAR button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
Move the cursor with the joystick to the desired alarm num-
ber, and then press the PLAY button. The associated image
will be played back.
●Electronic Zooming (EL-ZOOM)
The operations are the same as WJ-HD500 Series. (Refer to
p. 133.)
Note:2 x and 4 x are available zooming range. 8 x is
unavailable.
●Multiscreen Sequence
The operations are the same as WJ-HD500 Series. (Refer to
p. 134.)
    ALARM RECALL  YEAR03
 NO.  DATE  TIME     ALM
 2000 06-14 20:30:00  T1
 1999 06-14 15:30:12  T3
 1998 06-14 12:15:04  T4
 1997 06-14 12:15:02  V8
 1996 06-14 10:07:05  V2
 1995 06-14 10:07:04  T2
 1994 06-14 10:06:55  T6
 1993 06-14 09:58:32  V5
(TOTAL  2000EVENTS)
 TO SEARCH PUSH T&D KEY
UP
LR
DOWN 
						

							137
WJ-HD100 SERIES CONTROL  (TERMINAL MODE)MUX
Digital Disk Recorder WJ-HD100 Series are operable with
the system controller, when the Multiplexer board is
installed in the unit.
Note:Before the use, it is necessary to install the Multi-
plexer board in the matrix switcher, connect the
matrix switcher to the digital disk recorder, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and WJ-HD100 Series
SETUP MENU. [Refer to p. 32 Installing the
Multiplexer Board, p. 45 Connection with Digital
Disk Recorder WJ-HD100 Series, p. 63 WJ-SX150A
SETUP MENU (OSD), p. 79 WJ-SX150A ADMINIS-
TRATOR CONSOLE, and Displaying WJ-HD100
Series SETUP MENU in this page.]
■Displaying WJ-HD100 Series
SETUP MENU
The operations are the same as WJ-HD500 Series.
Refer to p. 130 Displaying WJ-HD500 Series SETUP MENU.
The following functions and buttons are valid in SETUP
MENU.
Joystick to R (B):Decrements a parameter
Joystick to L (A):Increments a parameter
■Controlling Digital Disk
Recorder WJ-HD100 Series
The following are the operating procedures of WJ-HD100
Series via the system controller.
●Multiscreen Segment Switching
The operating procedure is the same as WJ-HD500 Series.
(Refer to p. 131.) 
Note:7-, 10-, or 13-segment multiscreen display is unavail-
able.
●Normal Playback
The operations are the same as WJ-HD500 Series. (Refer to
p. 131.)
Notes:
•You cannot skip to the previous/next record.
•Refer to WJ-HD100 Series Operating Instructions for
details and other playback modes.
●Manual Recording
The operations are the same as WJ-HD500 Series. 
Refer to p. 132.
●Stopping REC ONLY Alarm
Recording
The operations are the same as WJ-HD500 Series. Refer to
p. 132.
●Search Playback
You can search playback images using the ALARM
RECALL table or the SEARCH table. 
Every time you press the INDEX button, the display will
change as follows.
Live image →Date-and-time entry form→ALARM RECALL
table →Live image
• Date-and-time Search Playback
The recorded images can be searched for through the date
and time.
1. Enter the recorder mode. (Refer to p. 131 Recorder
Mode.)
2. Press the INDEX button. The date-and-time entry form
will appear on the center of the monitor.
Note:The factory default setting is the current date and
time.
F2
INDEX
                 SEARCH
            YYYY/MM/DD HH:MM
            2002/05/07 19:32 
						

							138
3. Press the numeric buttons or NEXT/PREV button to
enter the desired date and time. The cursor can be
adjusted by moving the joystick rightward or leftward.
4. Press the PLAY button. After the search through the
date and time, the recorded image will be played.
5. To return to the multiscreen display, press the STOP
button.
Note:To cancel the entry form, press the CLEAR button.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
Move the cursor with the joystick to the desired alarm num-
ber, and then press the PLAY button. The associated image
will be played back.
   ALARM RECALL 1 OF 10
NO   DATE     TIME   ALM
99 JUN 9.00 00:00:00 * T
98 JUN 1.00 02:34:56   T
97 JUN 1.00 01:10:01 * V
96 MAY31.00 23:34:45   V
95 MAY30.00 02:00:20 * T
94 MAY14.00 05:30:31 * T
93 MAY 7.00 23:00:59   T
92 MAY 6.00 22:05:50   V
91 APR14.00 23:00:59 * T
90 APR14.00 16:06:34 * V
UP
LR
DOWN 
						

							139
TIME-LAPSE VCR CONTROL  [PANASONIC MODELS] (TERMINAL MODE)MUX
A time-lapse VCR (Panasonic Models) is operable with the
system controller, while connecting to the matrix switcher.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the time-lapse VCR, and con-
figure the system through WJ-SX150A Administrator
Console, OSD SETUP MENU, and time-lapse VCRs
SETUP MENU. [Refer to p. 32 Installing the
Multiplexer Board, p. 46 Connection with the Time-
lapse VCR (Panasonic Models), p. 63 WJ-SX150A
SETUP MENU (OSD), and p. 79 WJ-SX150A
ADMINISTRATOR CONSOLE.]
The following is the procedure of a Panasonic model time-
lapse VCR.
■Controlling the Time-lapse VCR
The following are the operating procedures of the time-
lapse VCR via system controllers.
●Multiscreen Segment Switching
The operations are the same as WJ-HD500 Series. 
Refer to p. 131 Multiscreen Display.
Note:7-, 10-, and 13- segment multiscreen display are
unavailable.
●Normal Playback
The operations are the same as WJ-HD500 Series. 
Refer to p. 131 Normal Playback.
Note:You cannot skip to the previous/next record.
●Fast-forward
1. Press the FF button to fast-forward the tape during the
stop.
2. To stop fast-forwarding, press the STOP button.
Note:Pressing the FF button during fast-forward  will
start playback.
●Rewind
1. During the stop, press the REW button to rewind the
tape.
2. Press the STOP button to stop rewinding.
Note:Pressing the PLAY button during rewind will start
playback.
●Manual Recording
The operations are the same as WJ-HD500 Series. 
Refer to p. 132 Manual Recording.
●Stopping REC ONLY Alarm
Recording
The operations are the same as WJ-HD500 Series. Refer to
p. 132. 
						

							140
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (TERMINAL MODE)MUX
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Notes:
•Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure the system through WJ-SX150A
Administrator Console, OSD SETUP MENU, and
time-lapse VCRs SETUP MENU. [Refer to p. 32
Installing the Multiplexer Board, p. 47 Connection
with the Time-lapse VCR (Non-Panasonic Models),
p. 63 WJ-SX150A SETUP MENU (OSD), and p. 79
WJ-SX150A ADMINISTRATOR CONSOLE.]
•You cannot control non-Panasonic time-lapse VCRs
from system controllers.
The following is the procedure of a non-Panasonic model
time-lapse VCR.
■Controlling the Time-lapse VCR
●Multiscreen Segment Switching
The operations are the same as WJ-HD500 Series.
Refer to p. 131 Multiscreen Segment Switching.
Note:7-, 10-, and 13- segment multiscreen display are
unavailable.
●Normal Playback
1. Enter the recorder mode. (Refer to p. 131 Recorder
Mode.)
2. Do the playback procedure using the buttons on the
front panel. (Refer to the time-lapse VCR’s operating
instructions for how to operate.)
3. Press the PLAY button. The playback image will appear
on the monitor.
4. To display the spot picture, press the numeric buttons
corresponding to the desired camera number, then
press the CAM [SET] button. Then, the active monitor
number with “-H**” (** is the logical camera number)”
will appear on the LED display. (Refer to p. 132 Normal
Playback for the illustration.)
●Other Operations
Refer to the time-lapse VCR’s operating instructions for how
to operate. 
						

							141
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
■Controlling the Recorder with a PS·Data System Controller
●Recorder Mode
Before operating the recorder, it is necessary to enter the recorder mode.
1. Select the desired monitor. (Refer to p. 125 Monitor Selection.)
2. In the PS·Data mode, a number is assigned to each recorder. To select a desired recorder, enter the corresponding num-
ber by pressing the numeric buttons.
Recorder Number
Master recorder 100
Slave 1 recorder 101
Slave 2 recorder 102
Slave 3 recorder 103
Slave 4 recorder 104
3. Press the CAM button.
The recorder image will be displayed on the selected monitor, and you will enter the recorder mode.
●Operations
1. Press the SHIFT button to activate the FUNCTION buttons.
2. Enter the desired function code, and then press the FUNCTION button. (Refer to the diagram.)
3. To select a camera channel, press the numeric button(s), then CAM button. The system will exit from the recorder mode,
and the selected camera image will be displayed on the monitor.
Notes:
•Only one operator can enter the recording mode. 
•The images from the recorder, which are displayed on the monitor, is conformed to the recorder setting.
•You cannot skip to the previous/next record by moving the joystick.
Exclusive use to stop recording
WJ-HD500 SERIES CONTROL (PS·DATA)
Function CodeNote
Forward field advance 1 Available only during pause
Backward field advance 2 Available only during pause
Pause 4
Playback 5
Recording 6 Equal to the REC button of the recorder
Stop recording and playback 8
Stop playback 9 Exclusive use to stop playback
Stop recording 10
Search forward 11
Search backward
Displaying a recorders OSD
12
19Pressing again will hide the display. 
						

							142
●Stopping REC ONLY Alarm Recording
You can stop alarm recording activated by “REC ONLY” setting of 430 CAMERA/440 ALARM PORT/450 SERIAL PORT/460
MUX MOTION DET in SETUP MENU (refer to pp. 68 and 69) or the Alarm Mode window in WJ-SX150A Administrator Console
(refer to p. 88).
To stop the alarm recording, press the ALM RESET button. 
						

							143
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
■Controlling the Recorder with a PS·Data System Controller
1. Enter the recorder mode. (Refer to p. 141.)
2. Press the SHIFT button to activate the FUNCTION buttons.
3. Enter the desired function code, and then press the FUNCTION button. (Refer to the diagram.)
4. To select a camera channel, press the numeric button(s), then CAM button. The system will exit from the recorder mode,
and the selected camera image will be displayed on the monitor.
Notes:
•Only one operator can enter the recording mode. 
•The images from the recorder, which are displayed on the monitor, is conformed to the recorder setting.
●Stopping REC ONLY Alarm Recording
The operations are the same as WJ-HD500 Series. Refer to p. 142.
WJ-HD200 SERIES CONTROL (PS·DATA)
Function Code Note
Forward field advance 1
Backward field advance
To the last field
Pause
Playback
Recording
To the first field
Stop recording and playback
Stop playback
Stop recording
Search forward
Search backward
Displaying a recorders OSD
2
3
4
5
6
7
8
9
10
11
12
19Equal to the REC button of the recorder
Exclusive use to stop playback
Exclusive use to stop recording
Searching will speed up every time you enter the code.
Searching will speed up every time you enter the code.
Pressing again will hide the display. 
						

							144
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
Note:Before the use, it is necessary to install the Multiplexer board in the matrix switcher, connect the matrix switcher to the
digital disk recorder, and configure the system through WJ-SX150A Administrator Console, OSD SETUP MENU, and WJ-
HD100 Series SETUP MENU. [Refer to p. 32 Installing the Multiplexer Board, p. 45 Connection with Digital Disk Recorder
WJ-HD100 Series, p. 63 WJ-SX150A SETUP MENU (OSD), p. 79 WJ-SX150A ADMINISTRATOR CONSOLE, and p. 137
Displaying WJ-HD100 Series SETUP MENU.]
■Controlling the Recorder with a PS·Data System Controller
●Recorder Mode
1. Enter the recorder mode. (Refer to p. 141.)
2. Press the SHIFT button to activate the FUNCTION buttons.
3. Enter the desired function code, and then press the FUNCTION button. (Refer to the diagram.)
4. To select a camera channel, press the numeric button(s), then CAM button. The system will exit from the recorder mode,
and the selected camera image will be displayed on the monitor.
Notes:
•Only one operator can enter the recorder mode. 
•The images from the recorder, which are displayed on the monitor, is conformed to the recorder setting.
●Stopping REC ONLY Alarm Recording
The operations are the same as WJ-HD500 Series. Refer to p. 142.
WJ-HD100 SERIES CONTROL  (PS·DATA)MUX
Function Code Note
Forward field advance 1
Backward field advance
To the last field
Pause
Playback
Recording
To the first field
Stop recording and playback
Stop playback
Stop recording
Search forward
Search backward2
3
4
5
6
7
8
9
10
11
12Equal to the REC button of the recorder
Exclusive use to stop playback
Exclusive use to stop recording
Searching will speed up every time you enter the code.
Searching will speed up every time you enter the code.