Panasonic Matrix Switcher Wj Sx150a Operating Instructions
Have a look at the manual Panasonic Matrix Switcher Wj Sx150a Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
64 ■TIME & DATE ●How to Display To display this menu on the monitor, move the cursor to 100 TIME & DATE in SETUP MENU by moving the joystick to D or C. ●Parameters You can move the cursor to each parameter by moving the joystick to Aor B. • Month Press the NEXT or PREV button to select the correct month. • Day Press the numeric buttons to enter it directly. WJ-SX150A SETUP MENU x.xx 100 TIME&DATE Aug/21/2002 10:55 AM 200 D.S.T. ON 300 SEQUENCE O 400 ALARMO 500 CAMERA TITLEO 600 RECORDERO 700 SYSTEMO 800 OPERATOR REGISTRATIONO 900 MULTIPLEXERO 1000 MUX CAMERA TITLEO
65
400 ALARM
410 ALARM MODE SEQUENCE
/ DWELL 2sec
420 ALARM EVENTOALARM INPUT
430 CAMERA OFF
440 ALARM PORT ONO 450 SERIAL PORT ON
460 MUX MOTION DET OFFO
500 CAMERA TITLE 2 of 2
CAM TITLE
9 C09
10 C10
11 C11
12 C12
13 C13
14 C14
15 C15
16 C16
600 RECORDER
CONTROL ADR EXT IN
610 MASTER ---
620 SLAVE1 HD100 01
630 SLAVE2 OFF GENLOCK OFF
640 SLAVE3 VCR
650 SLAVE4 HD500 01 GENLOCK OFF
--COMMUNICATION STATUS--
DATA BIT 7bit
PARITY BIT ODD
STOP BIT 1bit
BAUD RATE 9600bps
COMM PORT SERIAL PORT
Outside the U. S.:
· Aug/21/2002... 21/08/2002
· D. S. T.... SUMMER TIME
WJ-SX150A SETUP MENU x.xx 100 TIME&DATE Aug/21/2002 10:55 AM
200 D.S.T. ON
300 SEQUENCE
O 400 ALARMO 500 CAMERA TITLEO 600 RECORDERO 700 SYSTEMO 800 OPERATOR REGISTRATIONO
900 MULTIPLEXERO 1000 MUX CAMERA TITLEO
300 SEQUENCE 1 of 4
TOUR NO.= 1
STEP LCN PRE DWELL STEP LCN PRE DWELL
1 1 2S 9 9 2S
2 2 2S 10 10 2S
3 3 2S 11 11 2S
4 4 2S 12 12 2S
5 5 2S 13 13 2S
6 6 2S 14 14 2S
7 7 2S 15 15 2S
8 8 2S 16 16 2S
LCN:LOGICAL CAMERA NUMBER420 ALARM EVENT 10 of 10
ALM MON MODE REC ALARM PORT
CN(PRE)/TOUR
91 1 LCN 01
/ PRE01 /
92 1 LCN 02 / PRE01 /
93 1 LCN 03 / PRE01 /
94 2 TUR 04 /
95 1 LCN 05 / PRE01 /
96 1 LCN 06 / PRE01 /
97 1 LCN 07 / PRE01 /
98 1 LCN 08 / PRE01 /
99 1 LCN 09 / PRE01 /
LCN:LOGICAL CAMERA NUMBER
420 ALARM EVENT 2 of 10
ALM MON MODE REC ALARM PORT
LCN(PRE)/TOUR
11 1 LCN 01
/ PRE01 R1 MASTER / 11
12 1 LCN 02 / PRE01 R1 MASTER / 12
13 1 LCN 03 / PRE01 R1 MASTER / 13
14 2 TUR 04 R1 MASTER / 14
15 1 LCN 05 / PRE01 R1 MASTER / 15
16 1 LCN 06 / PRE01 R1 MASTER / 16
17 1 LCN 07 / PRE01 R2 SLAVE1 / 1
18 1 LCN 08 / PRE01 R2 SLAVE1 / 2
19 1 LCN 09 / PRE01 R2 SLAVE1 / 3
20 1 LCN 10 / PRE01 R2 SLAVE1 / 4
LCN:LOGICAL CAMERA NUMBER
420 ALARM EVENT 1 of 10
ALM MON MODE REC ALARM PORT
LCN(PRE)/TOUR
1 1 LCN 01
/ PRE01 R0 MASTER / 1
2 1 LCN 02 / PRE01 R0 MASTER / 2
3 1 LCN 03 / PRE01 R0 MASTER / 3
4 1 LCN 04 / PRE01 R0 MASTER / 4
5 1 LCN 05 / PRE01 R0 MASTER / 5
6 1 LCN 06 / PRE01 R0 MASTER / 6
7 1 LCN 07 / PRE01 R0 MASTER / 7
8 1 LCN 08 / PRE01 R0 MASTER / 8
9 1 LCN 09 / PRE01 R0 MASTER / 9
10 1 LCN 10 / PRE01 R0 MASTER / 10
LCN:LOGICAL CAMERA NUMBER
440 ALARM INPUT(ALARM PORT)
SWITCHER=SLAVE1(1 of 5)
1 NORMALLY OPEN 9 NORMALLY OPEN
2 NORMALLY CLOSE 10 NORMALLY OPEN
3 NORMALLY OPEN 11 NORMALLY OPEN
4 NORMALLY OPEN 12 NORMALLY OPEN
5 NORMALLY CLOSE 13 NORMALLY OPEN
6 NORMALLY OPEN 14 NORMALLY OPEN
7 NORMALLY OPEN 15 NORMALLY OPEN
8 NORMALLY OPEN 16 TIME ADJUST
700 SYSTEM
710 MASTER-SLAVEO 720 LOGICAL CAMERA NUMBERO 730 COMPENSATION/VD2/DATAO 740 CAMERA/DATA1-4 PORTO 750 RS485 CAMERAO 760 CAMERA CLEANING OFF
710 MASTER-SLAVE
MASTER *.**
SLAVE1 ON *.**
SLAVE2 ON *.**
SLAVE3 OFF *.**
SLAVE4 OFF *.**
“CAUTION”
Part of settings are initialized when
the MASTER-SLAVE composition is changed.
Is the MASTER-SLAVE changed? NO
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE1(1 of 4)
CAM LCN CAM LCN
1 1 9 9
2 2 10 10
3 3 11 11
4 4 12 12
5 5 13 13
6 6 14 14
7 7 15 15
8 8 16 16
LCN:LOGICAL CAMERA NUMBER
740 CAMERA/DATA1-4 PORT
SWITCHER=SLAVE1(1 of 5)
PORT MODE SPEED
CAMERA CAMERA 19200bps
DATA1 CAMERA 19200bps
DATA2 CAMERA 19200bps
DATA3 CAMERA 19200bps
DATA4 MASTER-SLAVE 38400bps
HDR HDR 9600bps
SERIAL -- 38400bps
750 RS485 CAMERA
SWITCHER=SLAVE1(1 of 5)
CAM LCN PORT CAM LCN PORT
1 21 9 51
2 22 10 52
3 23 11 53
4 24 12 54
5 25 13 55
6 26 14 56
7 27 15 57
8 28 16 58
LCN:LOGICAL CAMERA NUMBER
730 COMPENSATION/VD2/DATA 1 of 2
SWITCHER=SLAVE1(1 of 4)
CAM LCN COMP VD2 DATA
1 1 S ON ON
2 2 S ON ON
3 3 S ON ON
4 4 S ON ON
5 5 S ON ON
6 6 S ON ON
7 7 S ON ON
8 8 S ON ON
LCN:LOGICAL CAMERA NUMBER
800 OPERATOR REGISTRATION
OPERATOR NO.=1
ID =150 PRIORITY= 1
PASSWORD =∗∗∗∗∗ LEVEL = 1
SWITCHER=SLAVE1(1 of 5)
CAM LCN CAM LCN
1 21 VIEW&CONTROL 9 51 VIEW&CONTROL
2 22 VIEW ONLY 10 52 VIEW&CONTROL
3 23 VIEW&CONTROL 11 53 VIEW ONLY
4 24 VIEW ONLY 12 54 VIEW&CONTROL
5 25 VIEW&CONTROL 13 55 VIEW&CONTROL
6 26 VIEW&CONTROL 14 56 VIEW&CONTROL
7 27 VIEW&CONTROL 15 57 PROHIBITED
8 28 VIEW&CONTROL 16 58 PROHIBITED
900 MULTIPLEXER
SWITCHER=SLAVE1(1 of 5) Ver.∗.∗∗
VCR REC MODE
910 ALARM EXT.
920 NORMAL EXT.
930 DYNAMIC REC OFF
940 DUMMY BLACK ON
950 CAM SW LOSS ON
1000 MUX CAMERA TITLE
SWITCHER=SLAVE1(1 of 3)
CAM LCN TITLE CAM LCN TITLE
1 1 C01 9 09 C09
2 2 C02 10 10 C10
3 3 C03 11 11 C11
4 4 C04 12 12 C12
5 5 C05 13 13 C13
6 6 C06 14 14 C14
7 7 C07 15 15 C15
8 8 C08 16 16 C16
LCN:LOGICAL CAMERA NUMBER
500 CAMERA TITLE 1 of 2
SWITCHER=MASTER(2 of 2)
CAM LCN TITLE
1 -- ---
2 -- ---
3 -- ---
4 -- ---
5 17
6 18
7 19
8 20
LCN:LOGICAL CAMERA NUMBER
Depending on the composition of master-slave connection, parameters will differ from the illustration.
66
• Year
Press the numeric button to enter the correct year.
• TIME
Press the numeric button to enter the correct time.
• MINUTE
Press the numeric button to enter the correct minute.
• AM/PM
Press the NEXT or PREV button to select the correct time.
After the configuration, press the SETUP button while hold-
ing down the SHIFT button. The configuration will be updat-
ed when closing SETUP MENU.
Notes:
• Adjust the time and date when the clock display is differ-
ent from the current one.
• The clock display pattern is changeable with the setting in
WJ-SX150A Administrator Console. (Refer to p. 93.) The
factory default setting is Month/Day/Year.
• The clock is automatically adjusted to 0 second of the set-
ting time and date when closing SETUP MENU.
• Hour system (12- hours or 24- hours) is changeable
through WJ-SX150A Administrator Console.
■D. S. T. (Daylight Saving Time)
●How to Display
To display this menu on the monitor, move the cursor to 200
D. S. T. in SETUP MENU by moving the joystick to ▼or ▲.
●Parameters
Select ON or OFF by pressing the NEXT or PREV buttons.
ON:Daylight saving time is activated.
OFF:Daylight saving time is deactivated.
The factory default setting is ON.
After the configuration, press the SETUP button while hold-
ing down the SHIFT button. The configuration will be updat-
ed when closing SETUP MENU.
Notes:
•The start/end date are configurable through WJ-
SX150A Administrator Console. (Refer to p. 87.)
•When ON is selected for D. S. T., ∗is added beside the
time display.
Example:∗10: 55 AM
■SEQUENCE SETUP
●How to Display
To display this menu on the monitor, move the cursor to 300
SEQUENCE in SETUP MENU by moving the joystick to ▼or
▲.
Then, press the CAM (SET) button. The submenu appears
on the monitor.
WJ-SX150A SETUP MENU x.xx
100 TIME&DATE Aug/21/2002 10:55 AM
200 D.S.T. ON
300 SEQUENCE
O 400 ALARMO 500 CAMERA TITLEO 600 RECORDERO 700 SYSTEMO 800 OPERATOR REGISTRATIONO
900 MULTIPLEXERO 1000 MUX CAMERA TITLEO
300 SEQUENCE 1 of 4
TOUR NO.= 1
STEP LCN PRE DWELL STEP LCN PRE DWELL
1 1 2S 9 9 2S
2 2 2S 10 10 2S
3 3 2S 11 11 2S
4 4 2S 12 12 2S
5 5 2S 13 13 2S
6 6 2S 14 14 2S
7 7 2S 15 15 2S
8 8 2S 16 16 2S
LCN:LOGICAL CAMERA NUMBER
300 SEQUENCE 2 of 4
TOUR NO.= 1
STEP LCN PRE DWELL STEP LCN PRE DWELL
17 25
18 26
19 27
20 28
21 29
22 30
23 31
24 32
LCN:LOGICAL CAMERA NUMBER
300 SEQUENCE 3 of 4
TOUR NO.= 1
STEP LCN PRE DWELL STEP LCN PRE DWELL
33 41
34 42
35 43
36 44
37 45
38 46
39 47
40 48
LCN:LOGICAL CAMERA NUMBER
300 SEQUENCE 4 of 4
TOUR NO = 1
STEP LCN PRE DWELL STEP LCN PRE DWELL
49 57
50 58
51 59
52 60
53 61
54 62
55 63
56 64
LCN:LOGICAL CAMERA NUMBER
67
●Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
TOUR NO:Press the NEXT or PREV button to select the
tour number. Or press the numeric button(s) to
enter a number.
STEP: This stands for a tour sequence step.
LCN: This stands for a logical camera number. 01 to 99
or “- -“ is selectable. * To deactivate a sequence
step, select “- -“. You can set “- -“ by pressing the
button 0.
The factory default setting is assigned to each step
in numerical order (STEP 1 = LCN 1, STEP 2 = LCN
2, STEP 3 = LCN 3, STEP 4 = LCN 4, STEP 5 = LCN
5…)
PRE: This stands for a camera’s preset position num-
ber. 1 to 64 or - - is selectable. When the camera
has no preset position, select - -. You can set - -
by pressing the button 0.
The factory default setting is - -.
DWELL: This stands for the dwell time. 1 second to 30
seconds is selectable. To delete the sequence
step, select “- -“. You can set “- -“ by pressing the
button 0.
The factory default setting is 2S for each step.
After the configuration, press the MON (ESC) button. The
monitor display will return to the previous menu.
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
Notes:
•A preset position number is available only when a com-
bination camera is selected for CAM.
•The available preset position numbers differ among
cameras. Refer to each cameras operating instruc-
tions.
■ALARM SETUP
●How to Display
To display this menu on the monitor, move the cursor to 400
ALARM in SETUP MENU by moving the joystick to ▼or ▲.
Then, press the CAM (SET) button. The submenu appears
on the monitor.
●Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
• ALARM MODE
You can select an operation mode when alarm input signals
are accepted by the unit.
Notes:
•The alarm mode is activated when alarm input signals
are assigned to the same monitor through 420 ALARM
EVENT or the Alarm Event (refer to pp. 67 and 68/
pp. 89 and 90) window.
•While alarm is activated, you cannot operate the func-
tions related to the Multiplexer board.
SEQUENCE:An alarm operation is replaced by anoth-
er one after the dwell time (DWELL) ends.
HOLD:An initial alarm operation is continued even after
another alarm input is accepted.
OFF: Select this when not using the alarm mode.
The factory default setting is SEQUENCE.
• DWELL
This stands for the dwell time of a sequence during an
alarm mode.
1 to 30 seconds are selectable.
The factory default setting is 2 seconds.
• ALARM EVENT
This item is configurable in 420 ALARM EVENT.
Move the cursor and press the CAM (SET) button.
420 ALARM EVENT will appear on the monitor.
400 ALARM
410 ALARM MODE SEQUENCE
/ DWELL 2sec
420 ALARM EVENT
ALARM INPUT
430 CAMERA OFF
440 ALARM PORT ON
O 450 SERIAL PORT ON
460 MUX MOTION DET OFFO
420 ALARM EVENT 1 of 10
ALM MON MODE REC ALARM PORT
LCN(PRE)/TOUR
1 1 LCN 01
/ PRE01 R0 MASTER / 1
2 1 LCN 02 / PRE01 R0 MASTER / 2
3 1 LCN 03 / PRE01 R0 MASTER / 3
4 1 LCN 04 / PRE01 R0 MASTER / 4
5 1 LCN 05 / PRE01 R0 MASTER / 5
6 1 LCN 06 / PRE01 R0 MASTER / 6
7 1 LCN 07 / PRE01 R0 MASTER / 7
8 1 LCN 08 / PRE01 R0 MASTER / 8
9 1 LCN 09 / PRE01 R0 MASTER / 9
10 1 LCN 10 / PRE01 R0 MASTER / 10
LCN:LOGICAL CAMERA NUMBER
68
Notes:
•MODE and LCN(PRE/TOUR) cannot be selected by
pressing the numeric buttons. Press the NEXT or PREV
button for selection.
•PRE doesn’t appear when TOUR 1 to 16 is selected for
MODE.
•When selecting a camera without the preset position
function, select - - for PRE.
•When moving the joystick to ▼at the bottom of ALARM
EVENT 1 of 10, the monitor will display 2 of 10 (the next
page).
•When moving the joystick to ▲at the top of ALARM
EVENT 2 of 10, the monitor will display 1 of 10 (the pre-
vious page).
•Each ALARM PORT can be assigned to only one alarm
number. If you enter the same ALARM PORT more than
one time, the newer will be activated and the older will
be changed to a space.
•An alarm event will be activated even if the selected
logical camera number is not assigned to any camera
channel.
In this case, black image and “NOT ASSIGN” will be
displayed on the monitor.
•Set the parameter of a port number area by pressing
the numeric button(s).
•If you press the NEXT or PREV button at a port pin num-
ber area, the parameter will be switched among a
space and ALARM PORT not assigned to other alarm
events.
After the configuration, press the MON (ESC) button. The
monitor display returns to ALARM SETUP.
• ALARM INPUT
430 CAMERA
This stands for that an alarm input is accepted via the
CAMERA IN connectors or the RS-485 ports.
ON:The alarm-associated sequence/spot image is dis-
played on a monitor, and alarm recording will start
(if a recorder is connected to the unit).
REC ONLY:Only alarm recording will start and moni-
tors will keep displaying the current sequence/spot
images.
Note:You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF:An alarm input is accepted neither via the CAM-
ERA IN connectors nor the RS-485 ports.
The factory default setting is OFF.
440 ALARM PORT
This stands for that an alarm input is accepted via the
ALARM port (25-pin D-sub connector at the rear panel).
ON:The alarm-associated sequence/spot image is dis-
played on a monitor, and alarm recording will start
(if a recorder is connected to the unit.) ALM:This stands for the alarm event number.
MON:This stands for the monitor number.
MODE:This stands for the preset position of a camera
or tour sequence number activated with an alarm
input signal.
•LCN(PRE)/TOUR: Activates a spot camera or tour
sequence with an alarm input. To activate a spot
camera, select LCN nn (nn is a logical camera num-
ber: 01 to 99). To activate a tour sequence, select
TUR nn (nn is a tour number: 01 to 32).
When you selected a combination camera for LCN
nn, enter the desired preset position number. PRE
01 to 64 is available. When you selected another
type of camera, select “-“.
REC:This stands for a recorder activated with an alarm
input signal. If no recorder is activated, the parame-
ter will be a space. The REC area displays the num-
ber of recorder which receives images from a cam-
era whose logical camera number is correspondent
with the alarm event number.
R0 to R4 shows the following.
Recorder number Recorder
R0 Master recorder
R1 Slave 1 recorder
R2 Slave 2 recorder
R3 Slave 3 recorder
R4 Slave 4 recorder
420 ALARM EVENT 2 of 10
ALM MON MODE REC ALARM PORT
LCN(PRE)/TOUR
11 1 LCN 11
/ PRE01 R0 MASTER / 11
12 1 LCN 12 / PRE01 R0 MASTER / 12
13 1 LCN 13 / PRE01 R0 MASTER / 13
14 1 LCN 14 / PRE01 R0 MASTER / 14
15 1 LCN 15 / PRE01 R0 MASTER / 15
16 1 LCN 16 / PRE01 R0 MASTER / 16
17 1 LCN 17 / PRE01 R2 SLAVE1 / 1
18 1 LCN 18 / PRE01 R2 SLAVE1 / 2
19 1 LCN 19 / PRE01 R2 SLAVE1 / 3
20 1 LCN 20 / PRE01 R2 SLAVE1 / 4
LCN:LOGICAL CAMERA NUMBER
420 ALARM EVENT 10 of 10
ALM MON MODE REC ALARM PORT
LCN(PRE)/TOUR
91 1 LCN 91
/ PRE01
92 1 LCN 92 / PRE01
93 1 LCN 93 / PRE01
94 1 LCN 94 / PRE01
95 1 LCN 95 / PRE01
96 1 LCN 96 / PRE01
97 1 LCN 97 / PRE01
98 1 LCN 98 / PRE01
99 1 LCN 99 / PRE01
LCN:LOGICAL CAMERA NUMBER
Note:If a WJ-HD200 Series recorder is connected to
CAM 1 to 8, recorder number will be displayed
even camera channels (CAM 9 to 16) not connect-
ed to the recorder.
ALARM PORT:When an alarm port pin set here
receives an input signal, the designated event is
activated. MASTER, SLAVE 1 to 4 is available for
the matrix switcher. 1 to 16 is available for the alarm
port number. To deactivate the alarm number,
press the button 0. ALARM PORT will be a space.
The factory default setting is same as the illustrations.
69
REC ONLY:Only alarm recording will start and moni-
tors will keep displaying the current sequence/spot
images.
Note:You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF:An alarm input is not accepted via the ALARM
port.
The factory default setting is ON.
Each alarm inputs polarity is configurable in the submenu.
Set ALARM PORT to ON or REC ONLY, and press the CAM
(SET) button.
440 ALARM INPUT (ALARM PORT) will appear on the moni-
tor.
Move the cursor and press the CAM (SET) button to go into
the menu.
SWITCHER:Select a unit (SLAVE1 to 4 and MASTER*)
to configure the parameters.
*In normal connection, only MASTER is displayed.
After designating the unit, select the desired polarity for
ALARM 1 to 16.
NORMALLY OPEN:Normally Open contact is activat-
ed for the alarm input signal.
NORMALLY CLOSE:Normally Close contact is activat-
ed for the alarm input signal.
TIME ADJUST:This polarity enables the input of the
time adjusting signal.
The factory default setting is N. O.
Note:In the master-slave connection, time setting of
every unit can be synchronized when the time
adjusting signal is input to any unit.
450 SERIAL PORT
This stands for that an alarm input is accepted via the SERI-
AL port.
ON:The alarm-associated sequence/spot image is dis-
played on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY:Only alarm recording will start and moni-
tors will keep displaying the current sequence/spot
images. Note:You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF:An alarm input is not accepted via the SERIAL
port.
The factory default setting is ON.
460 MUX MOTION DET
This stands for that the unit’s motion detector is activated
when a camera detects the brightness-level change and
transmit an alarm signal.
ON:The alarm-associated sequence/spot image is dis-
played on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY:Only alarm recording will start and moni-
tors will keep displaying the current sequence/spot
images.
Notes:
•If the Multiplexer board is not installed in the
unit, you cannot enter the submenu of 460 MUX
MOTION DET.
•You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF:An alarm input is not accepted by the motion
detector.
To configure where to activate the motion detector, set
MUX MOTION DET to ON or REC ONLY, and press the
CAM (SET) button. The live image will be displayed.
Up to 4 motion-detection areas are configured for each
camera channel.
Note:Black image will be displayed on the monitor if
the currently selected channel has no camera con-
nection.
A “+” mark appears at the center of the monitor.
The following is the setting procedure.
MUX
+Mark
C01 LOW
Logical camera number and sensitivity
440 ALARM INPUT(ALARM PORT)
SWITCHER=SLAVE1(1 of 5)
1 NORMALLY OPEN 9 NORMALLY OPEN
2 NORMALLY CLOSE 10 NORMALLY OPEN
3 NORMALLY OPEN 11 NORMALLY OPEN
4 NORMALLY OPEN 12 NORMALLY OPEN
5 NORMALLY CLOSE 13 NORMALLY OPEN
6 NORMALLY OPEN 14 NORMALLY OPEN
7 NORMALLY OPEN 15 NORMALLY OPEN
8 NORMALLY OPEN 16 TIME ADJUST
1. Move the cursor with the joystick to the desired area, and then press the CAM (SET) key. Setting point 1 is determined. Note:If you control the joystick while holding down the SHIFT button, the cursor will move by 10 steps. Logical camera number and sensitivity level will move when a cursor points here. (The default position is here.) 2. Move the “+” mark to the desired area, and then press the CAM (SET) key. Setting point 2 is determined and the “+” mark will disappear. Then, the mark will appear again at the center of the monitor. The square, covered with Setting point 1 and 2, is showing the motion-detec- tion area. Note:White images will be displayed in the square if the currently selected channel has no camera connection. 3. To configure more motion-detection area, repeat Step 1 and 2. 4. To set the motion-detection area of another camera, press the NEXT or PREV button. Then, select the desired logical camera number. The live image of the selected camera will be displayed. Setting point 1 Setting point 2 + C01 LOW Notes: •If you repeat Step 1 after setting 4 motion-detection areas, “NG” will blink at the center of the monitor for two seconds. •To reset a motion-detection area, move the “+” mark on the desired area. Then, press the CLEAR button. The area will be reset. •If an area overlaps another one, the newer area will be reset. 5. To configure the motion-detection areas of another camera channel, press the NEXT or PREV button. 6. Repeat Step 1 to 4. Notes: •If you press the CLEAR button while holding down the SHIFT button, all the motion-detection areas of the cam- era channel will be cleared. •Depending on the sensitivity level, a motion-detection area needs the following area sizes. You can change the sensitivity level in WJ-SX150A Administrator Console (Refer to p. 89.) The factory default setting is LOW. After the configuration, press the MON (ESC) button. The motion-detection setting will be memorized and the monitor display will return to the previous menu. After all the configurations, press the SETUP button while holding down the SHIFT button. The configuration will be updated when closing SETUP MENU. 70 + Setting point + C01 LOW C01 LOW Sensitivity LOWArea size 17 x 17 steps or more MID 12 x 12 steps or more HIGH 5 x 5 steps or more
71
2. After the configuration, press the MON (ESC) button.
The monitor display will return to the previous menu.
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
Notes:
•When moving the joystick to ▼at the bottom of CAM-
ERA TITLE 1 of 2, the monitor will display 2 of 2 (the
next page).
•When moving the joystick to ▲at the top of CAMERA
TITLE 2 of 2, the monitor will display 1 of 2 (the previous
page).
•Original characters are configurable through WJ-
SX150A Administrator Console, but they are not dis-
played correctly in SETUP MENU. They are displayed
as ■. (Refer to p. 95 Edit Font window.)
•The titles of the camera channels deactivated by the
master-slave connection are displayed as “- - -“.
■RECORDER ■CAMERA TITLE●How to Display
To display this menu on the monitor, move the cursor to 500
CAMERA TITLE in SETUP MENU by moving the joystick to
▼or ▲. Then, press the CAM (SET) button. The submenu
appears on the monitor.
●How to edit
Move the joystick to move the cursor.
To select parameters, press the PREV or NEXT button.
SWITCHER:Select a unit (SLAVE1 to 4 and MASTER*)
to configure the parameters.
* In normal connection, only MASTER is displayed.
CAM:This stands for a camera channel of the unit.
LCN:This stands for a logical camera number. 1 to 99
is selectable.
TITLE:A camera title is composed of up to 20 charac-
ters. Each camera number is fixed and the subse-
quent 20 characters are editable.
The characters available here are the following:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrs
tuvwxyz0123456789!#$%&()*+,-./:;=?•_(space)
The factory default settings are same as the illustrations.
1. Edit the camera titles by pressing the NEXT or PREV
buttons.
The NEXT button toggles these characters in this order.
The PREV button toggles these characters in a reverse
order.
Joystick and the CLEAR button are also usable for the
edit. (Refer to p. 63 Displaying SETUP MENU for each
use.)
500 CAMERA TITLE 1 of 2
SWITCHER=MASTER(2 of 2)
CAM LCN TITLE
1 -- ---
2 -- ---
3 -- ---
4 -- ---
5 17
6 18
7 19
8 20
LCN:LOGICAL CAMERA NUMBER
500 CAMERA TITLE 2 of 2
SWITCHER=MASTER(2 of 2)
CAM LCN TITLE
9 21
10 22
11 23
12 24
13 25
14 26
15 27
16 28
LCN:LOGICAL CAMERA NUMBER
600 RECORDER
CONTROL ADR EXT IN
610 MASTER ---
620 SLAVE1 HD100 01
630 SLAVE2 OFF GENLOCK OFF
640 SLAVE3 VCR
650 SLAVE4 HD500 01 GENLOCK OFF
--COMMUNICATION STATUS--
DATA BIT 7bit
PARITY BIT ODD
STOP BIT 1bit
BAUD RATE 9600bps
COMM PORT SERIAL PORT
●How to Display
To display this menu on the monitor, move the cursor to 600
RECORDER in SETUP MENU by moving the joystick to D
or C. Then, press the CAM (SET) button. The submenu will
appear on the monitor.
●Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
• 610 MASTER/620 SLAVE1/630 SLAVE 2/640
SLAVE 3/650 SLAVE 4
This stands for the type of units connected in the sys-
tem.
CONTROL:This stands for the recorder connected to
each unit. The selectable parameters will differ
depending on whether a Multiplexer board is
installed in the unit.
72 Without the Multiplexer board HD500:Select this when a WJ-HD500 Series recorder is connected to the unit. HD200:Select this when a WJ-HD200 Series recorder is connected to the unit. OFF:Select this when no recorder is connected to the unit. The factory default setting is HD500. With the Multiplexer board VCR:Select this when a time-lapse VCR (Panasonic model) is connected to the unit. HD100:Select this when a WJ-HD100 Series recorder is connected to the unit. OFF:Select this when a time-lapse VCR (non- Panasonic model) or no recorder is connected. The factory default setting is OFF. Notes: •If HD500 or HD200 is selected for the unit with the Mul- tiplexer board, the parameter will be set to OFF. •If VCR or HD100 is selected for the unit without the Mul- tiplexer board, the parameter will be set to HD500. ADR:This stands for the recorder’s unit address. When a digital disk recorder is connected to the unit, 1 to 99 is available. When a time-lapse VCR is connect- ed, this parameter is not displayed. EXT IN: This stands for the setting of the EXT IN connector at the unit’s rear panel. When the Multiplexer board is installed in the Master unit, this parameter for MASTER does not appear. GENLOCK ON:Select this mode if you gen-lock the unit with an external device. GENLOCK OFF:Select this mode if you connect the video output connector of the recorder to the EXT IN connector of the unit. The factory default setting is OFF. The factory default setting is same as the illustration. • COMMUNICATION STATUS The following are communication parameters of a digi- tal disk recorder/time-lapse VCR. The parameters will differ depending on connected devices. When a digital disk recorder is connected DATA BIT:8 bit PARITY BIT:NONE STOP BIT:1 bit BAUD RATE:9600 bps COMM PORT:DATA HDR PORT When a time-lapse VCR is connected DATA BIT:7 bit PARITY BIT:ODD STOP BIT:1 bit BAUD RATE:9600 bps COMM PORT:SERIAL PORT Notes: •620 SLAVE1, 630 SLAVE 2, 640 SLAVE 3, and 650 SLAVE 4 appear only when they are connected. •When Slave 1 to 4 are connected in the system, “---“ is displayed for CONTROL of 610 MASTER. •If GENLOCK ON is selected, the playback images or multiscreen display cannot be displayed on Monitor 1 to 4. Confirm the images on the monitor which are con- nected to the recorder. •If GENLOCK OFF is selected, the maximum rate recording becomes unavailable (when a WJ-HD500 Series recorder is connected to the unit). •Gen-lock is not activated for the Slave 1 to 4 units when the Multiplexer board is installed in them. ■SYSTEM SETUP ●How to Display To display this menu on the monitor, move the cursor to 700 SYSTEM in SETUP MENU by moving the joystick to ▼or ▲. Then, press the CAM (SET) button. The submenu appears on the monitor. ●Parameters Move the joystick to move the cursor. Press the NEXT or PREV button to select the desired para- meters. • MASTER-SLAVE This menu links to the submenu. Move the cursor and press the CAM (SET) button to go into the menu. 710 MASTER-SLAVE will appear on the monitor. 700 SYSTEM 710 MASTER-SLAVE O 720 LOGICAL CAMERA NUMBERO 730 COMPENSATION/VD2/DATAO 740 CAMERA/DATA1-4 PORTO 750 RS485 CAMERAO 760 CAMERA CLEANING OFF
73
710 MASTER-SLAVE
MASTER *.**
SLAVE1 ON *.**
SLAVE2 ON *.**
SLAVE3 OFF *.**
SLAVE4 OFF *.**
“CAUTION”
Part of settings are initialized when
the MASTER-SLAVE composition is changed.
Is the MASTER-SLAVE changed? NO
SLAVE 1 to 4
ON:Select this for units connected in the system.
OFF:Select this for units not connected in the system.
The factory default setting is OFF.
Notes:
•For Slave units, you can set ON only when the unit with
the previous number is set to ON.
•When you change ON/OFF, part of the setting data will
be initialized according to the master-slave composition
•*. ** is the firmware version of a unit. (For Slave units,
the version is displayed only when ON is selected.)
Is the MASTER-SLAVE changed?
YES:Select this if you agree that the master-slave com-
position will be changed.
NO:Select this if you do not agree that the master-slave
composition will be changed.
This message appears only when you try to change
ON/OFF of SLAVE1 to 4.
•To change the setting, select “YES” and press the SET
button. SETUP MENU will be closed, but the setting will
be activated.
•To cancel the setting, select “NO”. The message will
disappear and the cursor moves to the former position.
After the configuration, press the MON (ESC) button. The
monitor display returns to the previous menu.
• LOGICAL CAMERA NUMBER
This menu links to the submenu.
Move the cursor and press the CAM (SET) button to go into
the menu. 720 LOGICAL CAMERA NUMBER will appear on
the monitor.
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE1(1 of 4)
CAM LCN CAM LCN
1 1 9 9
2 2 10 10
3 3 11 11
4 4 12 12
5 5 13 13
6 6 14 14
7 7 15 15
8 8 16 16
LCN:LOGICAL CAMERA NUMBER
CAM
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE2(2 of 4)
CAM LCN CAM LCN
1 17 9 25
2 18 10 26
3 19 11 27
4 20 12 28
5 21 13 29
6 22 14 30
7 23 15 31
8 24 16 32
LCN:LOGICAL CAMERA NUMBER
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE3(3 of 4)
CAM LCN CAM LCN
1 33 9 41
2 34 10 42
3 35 11 43
4 36 12 44
5 37 13 45
6 38 14 46
7 39 15 47
8 40 16 48
LCN:LOGICAL CAMERA NUMBER
720 LOGICAL CAMERA NUMBER
SWITCHER=MASTER(4 of 4)
CAM LCN CAM LCN
1 -- 9 --
2 -- 10 --
3 -- 11 --
4 -- 12 --
5 -- 13 49
6 -- 14 50
7 -- 15 51
8 -- 16 52
LCN:LOGICAL CAMERA NUMBER
CAM12345678910111213141516
Master12345678910111213141516
When Master and Slave 1 are connected
CAM12345678910111213141516
Slave 112345678910111213141516
Master - - - - - - - - 17 18 19 20 21 22 23 24 25 26 27 28
12345678910111213141516
Slave 112345678910111213141516
Slave 1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Master - - - - - - - - - - - - - - - - 33 34 35 36 37 38 39 40
When Master, Slave 1 and 2 are connected Move the joystick to move the cursor.
To select parameters, press the PREV or NEXT button.
SWITCHER:Select a unit (SLAVE1 to 4 and MASTER*) to
configure the parameters
* In normal connection, only MASTER is displayed.
CAM:This stands for a camera channel of the unit.
LCN:This stands for a logical camera number. 1 to 99 is
selectable.
The factory default settings are shown in the diagrams.
When only Master is connected