Panasonic Matrix Switcher Wj Sx150a Operating Instructions

114
■ Tour Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJ-
SX150A Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor and camera. (Refer to p. 106
Monitor Selection and p. 107 Camera Selection.)
2. To select the desired tour sequence number, press the
numeric buttons.
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the TOUR...

115
■ On-screen Display (OSD)
Control
The procedure described below lets you determine the dis-
play parameters, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is neces-
sary. (Refer to p. 106 Monitor Selection.)
●Displaying the Clock 
Toggle the button 1 while holding down the OSD button. 
(1) will appear/disappear on/from the active monitor.
●Displaying the Camera Title
Toggle the button 2 while holding down the OSD...

116
The columns in the table indicate the states as shown in the
figure.
MON:Monitor number
CAM:Logical camera number (01 to 99)
Recorder number (R0 to R4)*
No number indicates no camera is
selected. 
MODE:Lists the display mode on the
monitors.
SPOT:Spot mode
Tnn:Tour Sequence mode (nn is the
tour sequence number.)
CAM:Camera Setup mode
SET:WJ-SX150A Setup mode
ALARM:Alarm Active mode
ACK:Alarm ACK mode
VLD H:Video Loss History Table 
ALM H:Alarm History  Table
SYS S:System Status Table...

117
■ Alarm History Table
There are 100 alarm records stored in chronological order
in 10 pages of tables.
1. Select the desired monitor. (Refer to p. 106 Monitor
Selection.)
2. Press the button 7 while holding down the OSD button.
OSD will appear on the LED display, and the ALARM
HISTORY table will appear on the active monitor as
shown in the figure.
The columns in the table indicate the states as follows:
DATE:Lists the date and time when the alarm state
changes.
ALARM:Lists the alarm number (01 -...

118
■Operation during an Alarm Mode
While an alarm mode is active, the following are available
from the system controller:
•Operating the camera with the alarm input (ACK)
•Resetting the alarm (RESET/ALL RESET)
•Suspending the alarm (ALM SUSPENDED)
■Operation of an Alarm-related
Camera (ACK)
You can operate the camera with the alarm input as follows:
1. Select a monitor which displays ALARM.
2. Press the ACK button.
ACK will appear on the monitor with an alarm input.
The camera with an alarm input will...

119
1. Press the ACK/SUSPEND button while holding down
the SHIFT button.
ALM SUSPENDED will appear on the monitor.
2. To cancel alarm suspension, press the ACK/SUSPEND
button while holding down the SHIFT button again.
ALM SUSPENDED will disappear from the monitor.
Notes:
•An alarm continues to operate even after it is suspend-
ed.
•
If you suspend an alarm while an alarm image is dis-
played, ALM SUSPENDED will not appear on the moni-
tor. Reset the alarm, and then suspend it 
again. 
■Resetting the...

120
MULTIPLEXER OPERATIONS MUX
Multiplexer board WJ-SXB151 is an optional board.
It enables multiscreen display, electronic zooming, still pic-
ture and multiscreen sequence.
It also enables the operation of Digital Disk Recorder WJ-
HD100 Series or time-lapse VCR, when connected to them.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher and config-
ure the system through SETUP MENU and WJ-
SX150A Administrator Console. [Refer to p. 32
Installing the Multiplexer...

121
8. To cancel the zooming, press the button 4 while holding
down the SHIFT button again.
Note:Still picture is not available while zooming is acti-
vated. 
Note:When a WJ-HD100 Series recorder or a Panasonic
time-lapse VCR is connected to the unit, recording sta-
tus will appear on the monitor in the recorder mode.
When the normal recording is activated, “REC” will
appear on the monitor. When the alarm recording is
activated, “REC ALM” will appear.●Still Playback Spot Picture
The playback spot picture...

123
OPERATING PROCEDURES
(PS·DATA) 

124
WHEN USING A PS·DATA SYSTEM CONTROLLER
This manual describes the operating procedures which are specifically related to WJ-SX150A.
For the basic operating procedures such as log-in/log-out, camera selection, and camera control, etc., refer to the system con-
trollers operating instructions.
The following are different from the terminal mode when you use the system controller via the PS·Data protocol.
•Camera selection, camera control, camera site accessories control are in accordance with the PS·Data...