Panasonic Matrix Switcher Wj Sx150a Operating Instructions

64
■TIME & DATE
●How to Display
To display this menu on the monitor, move the cursor to 100
TIME & DATE in SETUP MENU by moving the joystick to D
or C.
●Parameters
You can move the cursor to each parameter by moving the
joystick to Aor B.
• Month
Press the NEXT or PREV button to select the correct month.
• Day
Press the numeric buttons to enter it directly.
 WJ-SX150A SETUP MENU                x.xx
  100 TIME&DATE     Aug/21/2002 10:55 AM
  200 D.S.T.        ON           
  300 SEQUENCE
O  400 ALARMO...

65
 400 ALARM
 410 ALARM MODE    SEQUENCE 
/ DWELL 2sec
 420  ALARM EVENTOALARM INPUT
 430       CAMERA OFF
 440       ALARM PORT ONO 450       SERIAL PORT ON
 460       MUX MOTION DET  OFFO
 500 CAMERA TITLE         2 of 2
       CAM  TITLE
         9  C09
        10  C10
        11  C11
        12  C12
        13  C13
        14  C14
        15  C15
        16  C16
 600 RECORDER
             CONTROL   ADR   EXT IN
 610 MASTER  ---
 620 SLAVE1  HD100      01
 630 SLAVE2  OFF             GENLOCK OFF
 640...

66
• Year
Press the numeric button to enter the correct year.
• TIME
Press the numeric button to enter the correct time.
• MINUTE
Press the numeric button to enter the correct minute.
• AM/PM
Press the NEXT or PREV button to select the correct time.
After the configuration, press the SETUP button while hold-
ing down the SHIFT button. The configuration will be updat-
ed when closing SETUP MENU. 
Notes:
• Adjust the time and date when the clock display is differ-
ent from the current one.
• The clock...

67
●Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
TOUR NO:Press the NEXT or PREV button to select the
tour number. Or press the numeric button(s) to
enter a number.
STEP: This stands for a tour sequence step.
LCN: This stands for a logical camera number. 01 to 99
or “- -“ is selectable. * To deactivate a sequence
step, select “- -“. You can set “- -“ by pressing the
button 0.
The factory...

68
Notes:
•MODE and LCN(PRE/TOUR) cannot be selected by
pressing the numeric buttons. Press the NEXT or PREV
button for selection.
•PRE doesn’t appear when TOUR 1 to 16 is selected for
MODE.
•When selecting a camera without the preset position
function, select - - for PRE.
•When moving the joystick to ▼at the bottom of ALARM
EVENT 1 of 10, the monitor will display 2 of 10 (the next
page).
•When moving the joystick to ▲at the top of ALARM
EVENT 2 of 10, the monitor will display 1 of 10 (the pre-
vious...

69
REC ONLY:Only alarm recording will start and moni-
tors will keep displaying the current sequence/spot
images.
Note:You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected. 
OFF:An alarm input is not accepted via the ALARM
port.
The factory default setting is ON.
Each alarm inputs polarity is configurable in the submenu.
Set ALARM PORT to ON or REC ONLY, and press the CAM
(SET) button.
440 ALARM INPUT (ALARM PORT) will appear on the moni-
tor.
Move the cursor and...

1. Move the cursor with the joystick to the desired area,
and then press the CAM (SET) key. Setting point 1 is
determined.
Note:If you control the joystick while holding down the
SHIFT button, the cursor will move by 10 steps.
Logical camera number and sensitivity level will move
when a cursor points here. (The default position is
here.) 
2. Move the “+” mark to the desired area, and then press
the CAM (SET) key. Setting point 2 is determined and
the “+” mark will disappear. Then, the mark will appear...

71
2. After the configuration, press the MON (ESC) button.
The monitor display will return to the previous menu. 
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
Notes:
•When moving the joystick to ▼at the bottom of  CAM-
ERA TITLE 1 of 2, the monitor will display 2 of 2 (the
next page).
•When moving the joystick to ▲at the top of CAMERA
TITLE 2 of 2, the monitor will display 1 of 2 (the previous
page)....

72
Without the Multiplexer board
HD500:Select this when a WJ-HD500 Series recorder
is connected to the unit.
HD200:Select this when a WJ-HD200 Series recorder
is connected to the unit.
OFF:Select this when no recorder is connected to the
unit.
The factory default setting is HD500.
With the Multiplexer board
VCR:Select this when a time-lapse VCR (Panasonic
model) is connected to the unit.
HD100:Select this when a WJ-HD100 Series recorder
is connected to the unit.
OFF:Select this when a time-lapse VCR...

73
 710 MASTER-SLAVE
               MASTER         *.**
               SLAVE1   ON    *.**
               SLAVE2   ON    *.**
               SLAVE3   OFF   *.**
               SLAVE4   OFF   *.**
 “CAUTION”
 Part of settings are initialized when
 the MASTER-SLAVE composition is changed.
  Is the MASTER-SLAVE changed?  NO
SLAVE 1 to 4
ON:Select this for units connected in the system.
OFF:Select this for units not connected in the system.
The factory default setting is OFF.
Notes:
•For Slave units, you can...