Panasonic Matrix Switcher Wj Sx150a Operating Instructions

12
Signal type Function
Control signal Controls camera functions (pan/tilt, zooming, focusing, lens iris, preset position) and camera
site accessories.
Status signal Shows camera status.
Timing pulse (VD2) This signal is supplied to the unit to each camera.
Each figure shows the picture status with or without the timing pulse.
■Example of a SYSTEM with Basic Functions
The illustration in the next page shows the surveillance system in a parking lot as an example.
Before the connections, the matrix...

13
Monitor 2 displays Camera 6s image consistently in the spot mode.
Operators will observe the parking lot by looking at these images on a monitor in a management office.
Lamp
lights up.
(Aux 2)
Camera 1
Dwell time : 1 sCamera 4/position 1
Dwell time : 3 sCamera 4/position 2
Dwell time : 2 s
Gate
opens.
(Aux 1)s
s s
Camera 5
Dwell time : 30 s
s
s s
Camera 1
Camera 4 Camera 5
Sensor Aux 1
Aux 2 Receiver
Preset
position 2
Matrix switcherAlarm 3
Alarm
Sequence mode
Alarm
mode
s
s
Monitor 1
Monitor 2
s
t t...

14
TERMINAL MODE DESCRIPTIONS
In the terminal mode, each external device (such as a cam-
era, monitor, system controller, or a recorder, etc.) has the
name and number (Camera 1, etc.). When you control a
device, you are to select the device number and execute the
selection. For example, before controlling Camera 1, you will
press the numeric button 1, and then press the CAM (SET)
button. Each operator has a level and priority. When you try
to control a device beyond the level and priority, the PRO-...

15
SLAVE DOWN (Displayed when communication is not
established between the Master and Slave units: for
example, power/cable disconnection)
* “n” is a number.
Notes:
•When pressing the associated numeric button (1 to 5)
while holding down the OSD button, information is
turned on or off.
•When you select the LCN (logical camera number) not
assigned in the system, “NOT ASSIGN” will appear
beside the camera number.
●The Display Position
The display position of the information is adjustable with the
joystick...

16
In each step, the desired preset position of a camera can
be called and displayed.
Tour sequences are configurable in SETUP MENU and WJ-
SX150A Administrator Console.
Group Sequence
Group sequence is a function to display up to 4 tour
sequences in a group on up to 4 monitors. More than one
sequences can be activated at one time by registering
each tour sequence in a group.
Up to 4 tour sequences can be registered in a group.
Notes:
•Up to 4 group sequences are configurable in WJ-
SX150A Administrator...

17
Notes:
•The images cannot be displayed while cleaning the
camera. Use this function when continuous surveillance
is not necessary, such as after-hours time.
•Cameras which are operating or being in the sequence
mode are not cleaned.
•Camera selection will immediately stop the camera
cleaning.
•If noise remains in the monitor even after the camera
cleaning, there can be a malfunction. Stop using the
camera and consult qualified service personnel.
■Alarm-related Functions
This unit is equipped with 16...

18
●Sequence Mode
In the sequence mode, the unit displays the initial alarm
image on the monitor until the dwell time ends, even when
another alarm input is accepted. When the dwell time ends,
the unit automatically replaces the alarm image with the
next one.
●Hold Mode
In the hold mode, the unit continues to display the initial
alarm image until the alarm reset. With the alarm image on
the monitor, the unit notifies you that more than one alarm
input is accepted with * next to ALARM nn (nn is the
alarm...

19
■Extended Functions 
If a recorder is connected to the matrix switcher, the follow-
ing will be available.
●Recorder Connection
The operations are conducted with the buttons on the
recorder, system controller or PC.
•The setup of the recording device 
•The playback of the recorded images (the multiscreen
display, still picture, etc.) 
•The search for the recorded image
•Forward or backward search
•Forward of backward field advance
•Fast-forward
•Rewind
•Index
Refer to each devices operating...

20
●Multiplexer Board Function 
To use WJ-HD 100 Series or a time-lapse VCR as a recorder, you need to install a Multiplexer board inside the matrix switcher.
With the Multiplexer board installation, the following will be available.
• Multiscreen display
More than one camera images can be displayed in 4, 9, and 16 multiscreens.
The sequence output is also available.
As the sequence output, the following are configurable in WJ-SX150A Administrator Console.
•The images are switched within 4 multiscreens....

21
• Motion detector 
When the multiplexer board detects motions in the image, the Multiplexer board sends an alarm signal to the unit.
Then, the unit will send the alarm signal to the connected devices.
The areas can be divided in four segments, and the detection is conducted in each segment.
For example, this function can be applied to a time-lapse recording, which responds to the break-in at night.
Notes:
•The motion-detection area needs to be configured in SETUP MENU in advance.
•The range of the...