Panasonic Matrix Switcher Wj Sx150a Operating Instructions

22
In the factory default setting, you can control the unit, if you connect a PS·Data system controller to the DATA 4 port. For exam-
ple, if you connect a PS·Data unit supporting network connections (refer to p. 42), remote-control of the unit and the PS·Data
units will be available with a system controller or PC. 
When you use a PS·Data system controller, take notice the following:
•The administer authorization and log-in/log-out procedure differs from the unit. They are conformed to the system con-...

23
DETAILED PRODUCT
DESCRIPTION 

24
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
■ WJ-SX150A Matrix Switcher
● Front View
qOperation indicator (OPERATE)
Lights up when the power of the unit is turned on.
Note: The indicator will blink to indicate rising tempera-
ture in the matrix switcher.
When the indicator blinks, turn the power off and
refer servicing to qualified service personnel.
wReset button (RESET)
Resets and restarts the unit.
Note:The system configuration is not reset.
eUnit number selector (UNIT)
Normally, set this selector...

25
● Rear View
SIGNAL GND
POWER
AC IN
CAMERA1 12
23
3 2
DATA  3 D ATA  2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECT
MONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)
OUTIN
4 45
56
67
78
89
910
1011
1112
1213
1314
1415
1516
16
RS485(CAMERA)
DATA  4 DATA HDR
PS•DATADATA  1
t yuio!0
!1!2!3!4!5!6
!9!7!8
tCamera Output connectors (CAMERA OUT 1–16)
The video signal connected to the CAMERA IN connec-
tor is supplied at these connectors.
When the power of the matrix switcher is turned off,...

26
@0Operation indicator (OPERATE)
Lights up when the controllers power is turned on.
@1Link indicator (LINK)
Lights up when communication is established with the
matrix switcher.
@2Alarm indicator (ALARM)
Lights up when an alarm condition exists.
@3Monitor indicator (MONITOR)
Lights up when the monitor number appears on the
LED display.
@4LED Display
Displays the monitor number, camera number, numeric
entry and error status, etc.
@5Camera indicator (CAMERA)
Lights up when the camera number appears on...

27
#0Focus buttons (FOCUS NEAR/FAR)
Adjust the lens focus of cameras equipped with the
specified lens.
Press the NEAR and FAR buttons simultaneously. The
lens focus is adjusted automatically, if the specified
auto focus camera is equipped.
#1Zoom buttons (ZOOM WIDE/TELE)
Press these buttons to zoom the lenses equipped with
the specified cameras.
Press the WIDE and TELE buttons simultaneously dur-
ing the recorder mode. The recording is started.
#2Call Preset button (CALL PRESET/PROGRAM
PRESET)
To call...

28
$4Next button (NEXT)
Moves a tour sequence one step forward from the step
previously paused on the active monitor.
Also selects a camera. If the active monitor is in the
spot mode, press NEXT while holding down the CAM
(SET) button, to replace the currently selected camera
with the next higher-numbered camera.
During the recorder mode, this button moves the play-
back image one step forward.
$5Previous button (PREV)
Moves a tour sequence one step backward from the
step previously paused on the active...

29
DC 9V INDATA MODE
RISK OF ELECTRIC SHOCK. DO  NOT OPENRISQUE DE CHOCS ELECTROUES
NE PAS OUVRIR
0987654321
%9^0%8
CONTROLLER No.
%7
%6
%6Controller Number switch (CONTROLLER No.)
Selects a number for the system controller for identifica-
tion in a system. Normally, set the switch to number 1.
%7Mode Selection switches (MODE)
The operation mode of the system controller is selected
with these switches.
When you use a terminal-mode system controller, set
the switches to the positions shown in the figure....

31
INSTALLATIONS AND SYSTEM
CONNECTIONS 

32
Notes:
•An optional cooling fan attached inside the unit is
subject to wear. It needs to be replaced periodical-
ly.
Keep the temperature in the rack below 45 °C
(113 °F) at any time. 
•If the rack is subject to vibration, secure the rear of
the appliance to the rack by using additional mount-
ing brackets (procured locally).
■Installing the Multiplexer Board
To use WJ-HD100 Series or a time-lapse VCR as a
recorder, you need to install a Multiplexer board inside the
matrix switcher. Refer to the...