Panasonic Matrix Switcher Wj Sx150a Operating Instructions

33
SYSTEM CONNECTION EXAMPLES
■Basic System Connection
This is an example of basic system connection. 
Camera
16 Camera
1Camera
2Camera
3
CAMERA IN 1 to 16
ALARM IN 1 to 16 
Max. 4 System Controllers Terminal-mode PS·Data/Terminal-modeMONITOR OUT 1 to 4 Matrix Switcher
Note:Before connecting a terminal-mode system controller to the DATA 4 port, configure the system through SETUP
MENU or WJ-SX150A Administrator Console.
■System Expansion Connection
●Connection with Digital Disk Recorder WJ-HD500 Series or...

34
Notes:
•Before connecting a terminal-mode system controller to the DATA 4 port, configure the system through SETUP MENU or
WJ-SX150A Administrator Console.
•If an optional network board is installed inside the recorder and you are to control it from LAN (local area network) or the
Internet, refer to a service manual procurable in your area.
●Connection with Digital Disk Recorder WJ-HD100 Series or Time-lapse VCR 
•With the Multiplexer board, the recorded images of Camera 1 to 16  can be multiplexed to...

35
●Master-slave Connection
When applying this connection, up to 5 matrix switchers and 64 cameras can be connected in a surveillance control system.
One of the matrix switchers is designated as Master and the others are designated as Slave.
ALARM IN 1 to 16 
Max. 4 System Controllers Terminal-mode PS·Data/Terminal-modeMONITOR OUT 1 to 4 Matrix Switcher
Camera
16 Camera
1
Camera
2Camera
3
CAMERA IN
1 to 16
ALARM IN
1 to 16 
Camera
48 Camera
33
Camera
34Camera
35
CAMERA IN
1 to 16
ALARM IN
1 to 16  Matrix...

36
Connect non-multiplex type cameras to the CAMERA IN
connectors 1 to 16. For cameras equipped with RS-485
communication facilities, connect the RS-485 cable as fol-
lows.
Check the camera addresses when using RS-485 cameras.
Operations from the system controller will be invalid if the
camera addresses are set improperly.
•Use addresses from 1 to 16 for individual cameras.
•Do not set the same address for more than one camera
in an RS-485 chain.
•Before connecting the RS-485 camera(s) to DATA 1, 2...

37
■ Connection for RS-485 Type Camera
There are two options to connect the camera with the matrix
switcher, depending on the distance between them. 
One is Home Run wiring and the other is daisy chain
wiring. Home Run wiring has the transmission stability with
less transmission loss, and daisy chain wiring has connec-
tion flexibility with less data ports occupied. For data-multi-
plex type cameras, 900 meters (3 000 ft) is the limit to use
coaxial cable such as RG-59/U, BELDEN 9259 or equiva-
lent....

38
■ Connection with the Monitors
Connect the monitors to the MONITOR OUT connectors at
the units rear panel with the coaxial cable.
The connectors MONITOR OUT 1 to 4 are associated to
Monitor 1 to 4. When you control the monitors from a PS·
Data controller, the connectors MONITOR OUT are associ-
ated to Unit 1 to 4.
Martix Switcher
Monitor 1 Monitor 2 Monitor 4 Monitor 3
2 14
3MONITOR OUT
(A)(B)GND
OFF ON(A)(B)GND
OFF ON
WV-CPR450 and others
Set it to 2 or 4
(the same as
the connected
equipment).
The...

39
■ Connection with the Alarm
Sensors
Connect the sensor switches to the units alarm port, as
shown in the example.
Notes:
•Alarm inputs that are simultaneous or with very short
intervals will be ignored.
Allow for at least 100 ms interval from one alarm input to
the next.
•Confirm the alarm sensor type (N.O. or N.C.) and con-
figure the system through SETUP MENU (OSD) or WJ-
SX150A Administrator Console.
The factory setting is N.O.
N.O.:Normally Open alarm contact
N.C.:Normally Closed alarm contact...

40
■Connection with Digital Disk
Recorder WJ-HD500 Series
Note: Refer to a service manual procurable in your area, for
details on the connection with a recorder (after the net-
work board installation) to operate via LAN or the
Internet.
●To Confirm the Images from a
Recorder Connected to the Unit
The following is the description of the connection between a
recorder and this unit to confirm the images from the
recorder.
1. Set the unit address of the recorder to 1. Then, confirm
that the recorder’s...

41
●To Record the Camera Images in Maximum
Recording Rate
The following is the description of the connection between a
recorder and this unit for the maximum-rate recording.
1.Set the unit address of the recorder to 1. Then, set the
recorder’s CAMERA GENLOCK to ON in its SETUP
MENU. (Refer to the recorders operating instructions.)
2.Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
3.Connect the unit’s EXT IN connector to the recorder’s...

42
●To Control a Recorder via the
Network
The following is the description of the connection between
a recorder and this unit to control the recorder via the net-
work.
1. Set the recorders unit address to a number 5 or larger .
(Refer to the recorders operating instructions.)
2. Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
3. Connect the unit’s DATA HDR and DATA4 connectors
to the recorder’s DATA port with a daisy chain connec-
tion...