Panasonic Kx-tvs75, Kx-tvs100, Kx-tvs200 Voice Processing System Installation Manual

7.2 UTILITY COMMANDS
SYSTEM MAINTENANCE AND TROUBLESHOOTING
151
7.2.18 Circuit Condition Display (LMON)
This command is used to display the circuit condition every 1.5 s. To disable the display in the 
VT100 mode, 
Type [\]. When in the ASCII mode, the circuit condition is only displayed once. 
The command can be turned off by entering [\].
 
The following circuit conditions may be displayed.
7.2.19 DTMF Information Display (PUTD)
This command is used to display the DTMF tones the VPS receives and...

7.2 UTILITY COMMANDS
152SYSTEM MAINTENANCE AND TROUBLESHOOTING
To change the mode from PUTD to OFF, 
Type PUTD again. 
To set the mode for only 1 port, 
Type PUTD and the port number.
Sample display:
WARNING
PUTD is a command originally used when troubleshooting. Do not use this command 
for any other purpose. Do not disconnect the RS-232C connection while the PUTD 
command is enabled. This could cause data overflow.
$ PUTD
          Target Port : * * * * * * * * * * * *
$
$ PUTD
         Target Port :...

7.3 SYSTEM REPORTS
SYSTEM MAINTENANCE AND TROUBLESHOOTING
153
7.3 SYSTEM REPORTS
The System Administrator is able to generate 8 System Reports to monitor VPS operating 
status. The reports can be displayed on a data terminal or printed. The terminal or printer must 
be connected to the RS-232C port. The following 8 report options are available.
The following 4 reports can be cleared of all values and prepared for use again.
7.3.1 Mailbox Assignments
The Mailbox Assignments report provides information...

7.3 SYSTEM REPORTS
154SYSTEM MAINTENANCE AND TROUBLESHOOTING
Note
An X displayed on the screen indicates that the feature marked with the X is set to
YES.
7.3.2 COS (Class of Service) Assignments
This report provides information concerning all Class of Service numbers.
For a complete explanation of COS parameters, please see Table 45, 46, 47 and 48 in 
B3 SYSTEM ADMINISTRATION - SETTING COS (CLASS OF SERVICE) 
PARAMETERS. COS: Class of Service IVMBOX: Interview Mailbox
CExtn: Covering Extension  MN1st:...

7.3 SYSTEM REPORTS
SYSTEM MAINTENANCE AND TROUBLESHOOTING
155
Note
An X displayed on the screen indicates that the feature marked with the X is set to
Yes.
7.3.3 System Service Report
The System Service Report provides information about the VPSs usable ports. It also indicates 
the services assigned to each VPS port for Day, Night, and Holiday modes, and all incoming 
and outgoing call services. RtN: New Message Retention RtS: Saved Message Retention 
Time
Ln: Message Length Time CaN: Maximum Message...

7.3 SYSTEM REPORTS
156SYSTEM MAINTENANCE AND TROUBLESHOOTING
Applicable VPS ports depend upon the models.
7.3.4 Call Account Report
The VPS can store information for up to 84 outgoing calling sequences (for accounting and 
billing purposes). Outgoing calling information includes the mailbox numbers that executed 
outgoing calls, the telephone numbers called, the call dates, and call duration times. When the 
number of outgoing calling sequences reaches 84, this information is automatically sent to the...

7.3 SYSTEM REPORTS
SYSTEM MAINTENANCE AND TROUBLESHOOTING
157
Note
Applicable VPS ports depend upon the models.
7.3.6 Port Usage Statistics Clear
Clears the Port Usage Report for use again.
Type [Y] (yes) or 
[N] (no). If Y is entered, the system will clear the data. Wait until Port 
Usage Report Data Cleared!! appears on the screen before proceeding.To select the Port Usage Report, follow the menu path as shown: 
System Administration Top Menu - 2 - 1 - 5
Ta b l e  3 4  
FROM: The date and time of the...

7.3 SYSTEM REPORTS
158SYSTEM MAINTENANCE AND TROUBLESHOOTING
7.3.7 Disk Usage Report
The Disk Usage Report indicates the amount of disk storage used and the disk availability in 
minutes. It also presents the following statistics:
• The number of messages that were recorded by callers since the last clearing of this report.
• The number of messages that were copied since the last clearing of this report.
• The number of messages that were deleted by subscribers since the last clearing of this 
report.
•...

7.3 SYSTEM REPORTS
SYSTEM MAINTENANCE AND TROUBLESHOOTING
159
Type [Y] (yes) or 
[N] (no). If Y is entered, the system will clear the data. Wait until Disk 
Usage Report Data Cleared!! appears on the screen before proceeding.
7.3.9 Mailbox Usage Report
The Mailbox Usage Report provides information about the usage at specific mailbox. It 
includes the number of recorded messages, the total amount of outgoing calling time, and 
external message, message notification and group message delivery. 
Note...

7.3 SYSTEM REPORTS
160SYSTEM MAINTENANCE AND TROUBLESHOOTING
Note
New MSGs/Received MSGs/ED MSGs are current status indications. All else are
accumulated indications since the last clearing of this report.
7.3.10 Mailbox Usage Statistics Clear
The Mailbox Usage Report can be cleared of all values and prepared for use again.
Type [Y ] (yes) or 
[N] (no). If Y is entered, the system will clear the data. Wait until Mailbox 
Usage Report Data Cleared!! appears on the screen before proceeding.
7.3.11 Fax Call...