Panasonic Dbs 824 Instructions Manual

tt1ejusy lone (t51j uerecrron 11mer
Busy Tone (BT) Detection Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 27# (0-15)#
DescriptionUse this program to set the amount of time the DBS 824 will wait to detect a
busy tone from the CO before automatically 
rediaiing an outgoing callIf a
busy tone is not detected within this amount of time, the DBS 824 will not
automatically 
redial the number
Programming
FFl 3# 27# (0115)#
f
Timer Setting (Default=3
see the following table)
Table...

Busy Tone (BT) Detection TimerFFlRelated Programming
Auto Repeat Dialing Count 
FFl 2# l# 3447 (0-15)##
Wait Timer For Auto-Repeat Dialing FFl 3# 26# (0- 15)#
Dial Tone (DT) Detection Timer FFl 3# 28#
CO Busy Tone 
(BT) Detection for Auto-Repeat DialingFF2 (Trunk)# 22#
1-114DBS 824-l O-400Issued 3/l /95 

FFlDial Tone (DT) Detection Timer
Dial Tone (DT) Detection Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 28# (O-255)44
DescriptionUse this program to set the amount of time (in milliseconds) the DBS 824 willwait to detect a dial tone from the CO, before automatically 
redialing an
outgoing callIf a dial tone is not detected within this amount of time auto-
repeat dialing will not be carried 
out.
Programming
I
FFl 3#$ 28# (01255)#
$Timer Setting 
(Default=25,see the...

Automatic Night 2 fviode Start TimeFFl
Automatic Night 2 Mode Start Time
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 29# HHMM#
DescriptionThis option sets a time for the DBS 824 to automatically switch from ‘Night
1 
’ to ‘Night 2” mode This program uses the 24-hour time format
Programming
To set the automatic Night 2 mode start time
FFl 3# 29# (0000-2359)#
f
Night 2 Mode Start Time
(in 24-hour format)
To disable the automatic Night 2 mode start time
I ~~FFl 3## 29## CONF...

FFlRemote Programming ID Code
Remote Programming and DISA Codes
Remote Programming ID Code
Sofhnrare VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 4## (0000-9999)#
DescriptionThe Remote Programming ID Code allows you to enter the terminal
programming modeThis programming mode is used to enter programming
commands from a remote PC or a local PC connected directly to the SMDR
port (CNl)
You can enter the remote programming mode through any of these three
methods
lBy dialing into the system...

DISA Inbound Call ID CodeFFl
DISA Inbound Call ID Code
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 5# (0000-9999)#
DescriptionThis program allows you to enter a DISA ID code
Once a caller has dialed
into the DBS 824 using a DISA trunk, dialing this code provides direct access
to intercom dial tone
Programming
To set the DISA ID code
FFl 5# (OOOO-9999)#
t
4-Digit ID Code
To clear the DISA ID code
FFl !5## CONF ON/OFFI
Related ProgrammingDISA Outbound Call 
XD Code 1 FFl 6# l#...

FFlDISA Outbound Call ID Code 1
DISA Outbound Call ID Code 1
Software Version
CPC-S and CPC-M, Version 1 0 and higherAddress 
FF1 6# l# (0000-9999)#
DescriptionOnce a DISA caller has entered the system he/she can make an outside call
after entering a valid ID code
This program sets the first of two valid DISA Outbound Call ID Codes
Thesystem will accept either code to give the 
DISA caller an outside line(The
purpose of having two Outbound Call ID Codes is to be able to track two
groups of DISA 
callers...

DISA Outbound Call ID Code 2FFl
DISA Outbound Call ID Code 2
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 6## 2# (0000-9999)#
DescriptionOnce a DISA caller has entered the system, he/she can make an outside call
after entering a valid ID code
This program sets the second of two valid DISA Outbound Call ID Codes
The system will accept either code to give the DISA caller an outside line
(The purpose of having 
two Outbound Call ID Codes is to be able to track
two groups of DISA...

Programming Authorization Code
ID Code For System Programming
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 7# (OOOO-9999)#
DescriptionThis program assigns an ID code that can be dialed from a non-attendant
phone to enter the programming mode
Non-attendant extensions enter the programming mode by dialing 
#I98 and
then the ID Code entered in this address
Programming
To assign the ID code for system programming
Notes
I
FFl 7# (OOOO-9999)#
f
4-Digit ID Code
(Default=9!3!8)
To reset...

New Function ResetFFl
New Function Reset
New Function Reset
Software Version
CPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 8## 1# (01l)#
DescriptionThis feature is reserved for future use
New Function Reset Confirmation
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress: 
FFl 8# 2# (O-l)#
DescriptionThis feature is reserved for future use
1-122
DBS 824-l O-400
Issued 3/l /95