Home > Panasonic > Communications System > Panasonic Dbs 824 Instructions Manual

Panasonic Dbs 824 Instructions Manual

Here you can view all the pages of manual Panasonic Dbs 824 Instructions Manual. The Panasonic manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 241

CO Ring Cycle Detection Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FF1 3# 13# (03)#
DescriptionThis timer determines how long the DBS 824 attempts to detect an incoming
CO ring cycle
To ensure that the DBS 824 can recognize incoming trunkcalls, set this timer to equal the duration of the ring cycle including 
thefirston period and the first 
of period
For example if the ring cycle for an incoming trunk is 2 seconds on/ 4
seconds off, this parameter should be set to at least 6...

Page 242

CO Ring Cycle Detection TimerFFl
Programming.
FFl 3# 13## (O-3)#
f
0=4 seconds
1=6 seconds
2=8 seconds
3=10seconds
Related Programming
Inbound Ring Cycle Expansion Timer FFl 3# l#l-94
DBS 824-10-400Issued 3/l/95 

Page 243

FFlInbound Ring Cycle Expansion Timer
Inbound Ring Cycle Expansion Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3## 14## (O-1 5)#
DescriptionLf the incoming ring pattern for an extension (FF3 ExtPor# 38#) is set to
emulate CO ringing, an extension may sometimes receive a very short ring
burst when a trunk call begins ringingThis short ring burst occurs because
the DBS 824 received only part of the first “on 
’ burst (see Figure l-2) from
the trunkTo eliminate these short...

Page 244

Inbound Ring Cycle txpanslon lamertt1
13650 ms
14700 ms
15750ms
1-96DBS 824-10-400Issued 3/l/95 

Page 245

FFlDial Pause Timer
Dial Pause Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 15## (O-l 5)#
DescriptionThis program inserts a pause before outpulsing dialed digits, once a CO trunk
is accessed
Programming
FFl 3# 1% (O-15)#
t
Timer Setting (Default=1
see the following table)
Table I-19 Did pause timer values
11
12
13
14
15
11seconds
12seconds
13seconds
14seconds
15seconds
Issued 3/l /95DBS 824-l O-400l-97 

Page 246

PBX Flash TimerFFl
PBX Flash Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 16# (0-lO)#
DescriptionWhen the DBS 824 is behind a PBX, the FLASH key can be used to place a
call on hold
This timer determines how long the flash signal will last if the 
FLASH key is
pressed then immediately released
If the 
FLASH key is pressed and held down the flash signal w-ill last as long
as the key is pressed
Programming
FFl 3# 16# (0-lO)#
f
Timer Setting (Default=7,
see the following...

Page 247

FFlCall Forward--No Answer Timer
Call Forward--No Answer Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3## 17# (O-1 5)#
DescriptionThe Call Forward--No Answer Tier determines how long an unanswered
call will ring before it is sent to a secondary destinationFor example, the
timer 
determines how long an unanswered call will ring at an extension
before it transfers to the Call Forward--No Answer point.
Note: Separate timers are provided for Hunt Group--No Answer, CO
Delayed...

Page 248

Attendant Hold Recall Timer for Intercom CallsFFlAttendant Hold Recall Timer for Intercom Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 18# (O-l 2)##
DescriptionIf an attendant places an intercom call on hold, the held call will recall to the
attendant if it is not retrieved in the time specified by this address
Recall timing for attendant-held trunk calls is controlled by another program
address 
(FFl 3# 2#)
Programming
I
FFl 3# 18# (O-1 2)#
+
ITimer Setting (Default=2
see...

Page 249

FFlExtension Hold Recall Timer for Intercom Calls
Extension Hold Recall Timer for Intercom Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 19# (0-12)#
DescriptionIf an extension places an intercom call on hold, the held call will recall to the
extension if it is not retrieved in the time specified by this address
Recall timing for extension-held trunk calls is controlled by another programaddress 
(FFi 3# 3#)
_
Programming
FFl 3# 19# (0112)#Timer Setting (Default=7
see the...

Page 250

Attendant Transfer Recall Timer for Intercom CallsFFlAttendant Transfer Recall Timer for Intercom Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3## 2O# (0-12)#
DescriptionWhen an attendant transfers an intercom call to an extension the call will
recall to the attendant if it is not answered
This timer determines how long
the transferred call will ring the extension before it recalls
Programming
FFl 3#I 20# (0-12)#
$
Timer Setting (Default=1
see the following table)
Table 1 24...
Start reading Panasonic Dbs 824 Instructions Manual

Related Manuals for Panasonic Dbs 824 Instructions Manual

All Panasonic manuals