Home > Panasonic > Communications System > Panasonic Dbs 824 Instructions Manual

Panasonic Dbs 824 Instructions Manual

Here you can view all the pages of manual Panasonic Dbs 824 Instructions Manual. The Panasonic manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 291

Inbound Ring PatternFF2
Inbound Ring Pattern
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF2 (Trunk)# 
17# (0-9)#
DescriptionEach CO trunk can assigned a distinctive ring pattern for easy recognition of
the trunk during an incoming ringUp to 9 different ring patterns are
available
Programming
FF2 (l-6 or I-8)# 17# (0-9)#
ftTrunk Number
Inbound Ring Pattern
CPC-S l-6
(Default=O, see the following table)
CPC-M l-8
Table 2-1Inbound ring patterns
NotesTransferred CallsThis setting does not...

Page 292

FF2Trunk Disconnect Detection Timer
Trunk Disconnect Detection Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF2 (Trunk)# 
18# (0-15)#
DescriptionWhen the trunk side of a CO call disconnects, the CO sends the DBS 824 a
disconnect signal by opening the loop (cutting voltage) for a specified length
of time
This timer determines how long the DBS 824 expects the disconnect signal to
last. If set to default, an open loop of 350 ms or more will be interpreted as a
disconnect signal
The...

Page 293

DISA Start TimeFF2
DISA Start Time
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FF2 (Trunk)# 19# (HHMM)#
DescriptionUse this address to program a DISA trunk to begin DISA operation at a
specified time each day
Trunks are enabled for DISA using the DISA AutoAnswer address 
(FF2 Trunl# ll#)Use this DISA Start Time address and
the DISA End Time address following, to limit DISA operation on a trunk to
a certain time period each day
Programming
To set the DISA start timeEnter the time using...

Page 294

FF2DISA End Time
DISA End Time
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF2 
(Trunk)## 20# (HHMM)#
DescriptionUse this address to program a DISA trunk to stop DISA operation at a
specified time each dayTrunks are 
enabled for DISA using the DISA Auto
Answer address 
(FF2 Trunl# 1 l#)Use this DISA End Tiie address, and the
DISA Start Time address (previous page), to limit DISA operation on a trunk
to a certain time period each day
NOTE: The DBS 824 will disable DISA to the trunk one...

Page 295

Trunk Circuit TypeFF2
Trunk Circuit Type
Software Version
CPC-M Only (Version 1 0 and above)
AddressFF2 (Trunk)# 21# (0 or l)#
DescriptionThis program determines whether a trunk circuit in a CPC-M configuration is
loop-start, or if it will support Caller ID
In a CPC-S configuration (which does not support Caller ID), all trunks are
loop-start
ProgrammingFF2 
(l-8)# 21# (0 or l)#
ftTrunk NumberO=Loop-startCPC-M 1-8l=Supports Caller ID
NotesCPC Card Requirement. This program address does not apply to the...

Page 296

FF2CO Busy Tone Detection
CO Busy Tone Detection
Software VersionCPC-S and CPC-M, Version 1 0 and higher
AddressFF2 (Trunk)# 
22# (0 or l)#
DescriptionThis address determines whether the DBS 824 system will look for a busy
tone from the CO for outgoing calls, for the purpose of activating the 
Auto-Repeat Dial feature
When this programming address is set to “on’
the DBS 824 will monitor
trunks for busy tone signals from the CO after outgoing calls are placed
if thebusy tone occurs, the DBS 824 will...

Page 297

CO Busy Tone DetectionFF2
Limitation on Monitoring of Trunks For Busy ToneThe DBS 824 canmonitor up to 2 trunks at the same time for busy tone
If a third trunk receivesa busy tone on an outgoing call while 2 other trunks are in Auto-Repeat
Dialing the system will not perform Auto-Repeat Dialing on the third trunk
2-20DBS 824-l O-400Issued 3/l /95 

Page 298

3. Extension Programming (FF3)Use the FF3 programming addresses in this chapter to set parameters for
extensionsWhen the programming address requires an extension port to be
entered, the acceptable range of port numbers varies depending on the model
of the CPC card in your DBS 824 systemCPC-S models have 
1-16 ports
CPC-M models have l-24 ports
This chapter covers the following topics
TopicPage
Extension Numbers3-3
Terminal TVpe3-5
13-6 11 EM/24 Port Assignment
1 Forced Least Cost Routing
I Forced...

Page 299

1 Extension Ring Pattern13-42 1
Digital SLT Receiving VolumeAuto Set Relocation Code3-44
3-45
1 Permanent Call Forward Type3-47Permanent Call Forward Extension
3-48
ML/MC0 Separation3-49VAU Hunting Priority
13-50 (
1 SLT Disconnect Signal13-51 IVAU Port Assignment
3-52Hot Dial Pad
3-53Auto-Redial on Extensions
3-543-2
DBS 824-10-400Issued 3/l/95 

Page 300

FF3Extension Numbers
Extension Numbers
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF3 (ExtPort)# 
l# (lo-69 or 100-699)#
DescriptionThis program assigns an extension number to an extension portAnextension number is the 2-digit or 3-digit number that is dialed to reach the
extension phone, extension numbers are programmable and can be changed
An extension port is the physical location 
(RJll jack) into which the phone is
plugged ports have fixed numbers which can’t be changed...
Start reading Panasonic Dbs 824 Instructions Manual

Related Manuals for Panasonic Dbs 824 Instructions Manual

All Panasonic manuals