Panasonic Dbs 824 Instructions Manual

ulyltar at- I newsI VII ty v UIUI I ICI I J
Digital SLT Receiving Volume
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF3 
(ExtPort)# 39# (0 or l)#
DescriptionThe receiver (hearing) volume of the handset on a digital single-line
telephone can be set to “normal” or “loud 
’
The “loud” setting gives a +6 dB gain over the ‘ normal” setting
(approximately twice as loud)
Programming
II
FF3 (l-16 or l-24)# 39# (0 or l)#
/ftExtension PortO=NormaiCPC-S 1-16
l=LoudCPC-M l-24
3-44DBS...

FF3Auto Set Relocation Code
Auto Set Relocation Code
Software VersiBnCPC-S and CPC-M, Version 1 0 and higherAddress FF3 (ExtPort)# 
40# (OOOl-9999)#
DescriptionYou can relocate (or swap) the program settings of one phone to anotherThe
Auto Set Relocation Code enables you to perform the relocation
For example, if the phone of extension 102 is unplugged and moved to an
office with a wall jack (port) assigned to extension 103, this feature can be
used to relocate 102’s programming to 103In order to move...

Auto Set Relocation CodeFF3
5Replace the handset. All programmed extension features, TRS and
LCR settings from 102 will be transferred to 103
Extension 103
will be placed out of service
6To return extension 103 to service, disconnect then reconnect the
extension cable
When extension 103 is returned to service, it will
have the program settings of extension 102
RestrictionsPhone settings cannot be exchanged between digital and analog
(SLTA) ports3-46
DBS 824-l O-400issued 3/l /95 

FF3Permanent Call Forward Type
Permanent Call Forward Type
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF3 (ExtPort)# 
41# (0-3)#
DescriptionUse this address to enable an extension for Permanent Call Forwarding, so
that calls to that extension (if the extension is busy and/or not answered) will
be forwarded to another location This feature is often used for sending calls
to Voice Mail, or forwarding peripheral equipment to a single extension port
ProgrammingFF3 (l-16 or 
l-24)# 41#...

Permanent Call Forward ExtensionFF3Permanent Call Forward Extension
Software 
VersionCPC-S and CPC-M, Version 1 0 and higher
Address FF3 (ExtPort)# 
42# (lo-69 or lOO-699)#
DescriptionIf an extension is enabled for Permanent Call Forwarding (in address FF3
ExtPor# 41#), use this address to set another extension number as the target
or ‘permanent call forwarding point’ for the forwarded calls
In addition to regular extension numbers, the permanent call forwarding point
can also be a System Speed Dial...

FF3ML/MC0 Separation
ML/MC0 Separation
Software VerdonCPCS and CPC-M, Version ‘I 0 and higher
AddressFF3 
(ExtPort)## 43#/ (0 or l)#Description
Use this address to program an extension to have MC0 (Multi-CO) or ML
(Multi-Line) FF keys
The difference between ML and MC0 has to do with incoming callsMC0
means multiple trunks can he received at the extension -- if you press a
flashing FF key, you will get an incoming trunk callCalls from another
extension will flash on the “EXT” LED (not through the FF key)...

VAU Hunting PriorityFF3VAU Hunting Priority
Software Versi6nCPC-S and CPC-M, Version 1 0 and higherAddress FF3 (ExtPort)# 
44# (0 or l)#
DescriptionThis program allows you to assign hunting priority to calls that overflow from
a hunt group to the VAUIf hunting priority is selected a caller that hears the
VAU message and then decides to dial back into the hunt group is placed
before other calls that have just entered the hunt group queue
Without hunting priority, the caller loses his or her place in the...

FF3SLT Disconnect Signal
SLT Disconnect Signal
Software VersionCPC-S and CPC-M, Version 1 0 and higher
AddressFF3 (ExtPort)# 45# (0 or l)#
DescriptionIf this program address is enabled, SLT extension ports will send a disconnect
signal (open loop) upon hangup
Sending this signal allows quick
disconnection from third-party voice mail systems
Programming
FF3 (l-16 or l-24)# 45# (0 or l)#
f$Extension Port
O=DisabledCPC-S 1-16
1 =EnabledCPC-M l-24
Related Programming
SLT Disconnect DurationFFl 2# l# 3 l#...

VAU Port AssignmentFF3VAU Port Assignment
Software Vers6nCPC-S and CPC-M, Version 1 0 and higher
AddressFF3 (ExtPort)# 46# (0 or l)#
DescriptionThis program assigns a digital port as a VAU (Voice Announce Unit)Once a
port is assigned as a VAU, the system treats that port as if the following
changes have been made
l The CO Offhook Signal option is set to “on” (FF3 ExtPort# 7#)
l The Call Waiting Notification Tone/OHVA option is set to “off’ (FF3
ExtPort# 8#)
l Auto Pickup is set to “on” (FF3 ExtPort#...

FF3Hot Dial Pad
Hot Dial Pad
Software VersionCPGS and CPC-M, Version 1 0 and higher
AddressFF3 (ExtPort)# 47# (0 or l)#
DescriptionThe dial pad on digital key phones can be designated as “hot” on an
extension-by-extension basis
This feature allows the user to initiate a call
without going 
offhook, by pressing any of the numeric keys O-9 (the “*” and
“#’ keys are not “hot”)
The extension’s dial pad can be “hot” under these conditionsl
when the extension is idle
lwhen the extension is holding a calll
when...