Panasonic Dbs 824 Instructions Manual

Extension NumbersFF3Clearing An Extension NumberClearing an extension port of its extension
number does not return the number to a default value -- instead, the port isinoperative until an extension number is reassigned to it and the phone is
unplugged from the system, then plugged back in
Re-Assigning An Extension NumberAn extension number can be changed
without clearing the old one first -- simply overwrite the old extension
number using this program address(The system will recognize the new
extension...

FF3Terminal Type
Terminal Type
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF3 
(ExtPort)# 2# (ExtType)#
DescriptionSome DBS 824 extensions are automatically configured when installed on an
extension portThe Terminal Type address allows you to change default
terminal assignments or assign special equipment to extension ports
ProgrammingFF3 (1-16 or 
l-24)# 2# (l-15)#
ft
Extension PortCPC-S 1-16
CPC-M l-24Terminal Type
(see the following table)
Table 3-1Terminal types
Note:If the...

EM/24 Port AssignmentFF3
EM/24 Port Assignment
Software VersionCPC-3 and CPC-M, Version 1 0 and higherAddress FF3 (ExtPort)# 
3# (ExtPort)#
DescriptionThis program assigns an EM/24 terminal to a key phone, matching up their
respective extension ports
The EM/24 terminal provides 24 additional FF keys to a key phone
It needsits own extension port. This address therefore requires two port number
entries --one for the EM/24 terminal, and one for the key phone
After the EM/24 is assigned to the key phone, the...

F-l-3Forcea L~~SI ~03 nourlngForced Least Cost Routing
Software VersionCPC-S and CPC-M, Version 1 0 and higher
AddressFF3 (ExtPort)# 
4# (0 or l)#
DescriptionUse this address to set individual extension(s) for forced Least Cost Routing
(LCR)If an extension is set for forced LCR the caller must dial9 or press
an FF key programmed for LCR in order to initiate an outside call
(Thecaller will now hear a dial tone generated by the DBS 824 -- but the system
will not access an outside line until the caller...

Forced Account CodesFF3Forced Account Codes
Software 
VersionCPC-S and CPC-M, Version 1 0 and higher
Address FF3 
(ExtPort) 5# (0-2)#
DescriptionWith this programming address, DBS 824 extensions can be programmed so
that the caller has to enter an account code before accessing a trunk for an
outgoing callThis address also enables or disables system verification of the
entered account code on an extension-by-extension basis
This programming
address affects the Toll Restriction Service 
(IRS) type used for...

Extension Lockout CodeSoftware VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF3 (ExtPort)# 
6# (OOOO-9999)#
DescriptionUse this address to assign a 4-digit lockout code to an extension
This allows
an extension user to ‘lock his/her phone before going away, thus preventing
unauthorized trunk calls during the user’s absence
Dialing ‘74” followed by
the extension lockout code will “lock” the extension
Dial 
“74” and the
lockout code again to “unlock’ the extension
Programming
To assign an extension...

Offhook Signal (CO)FF3
Offhook Signal (CO)
Software Versibn CPC-S and CPC-M, Version 1 0 and higherAddress 
FF3 (ExtPort)# 7# (0 or l)#
DescriptionThis program determines if the DBS 824 system sends a tone signal to busy
extensions when an additional trunk call arrives
Programming
To activate the Offhook SignalFF3 (l-16 or 
l-24)# 7# (0 or l)#
tExtension Port:
o=OffCPC-S 1-16
l=OnCPC-M l-24
Note: Default for the primary
attendant is 1 (on)
To reset the Offhook Signal to the default value
r-FF3 (l-16 or...

FF3Call Waiting/OHVA
Call Waiting/OHVA
Software VersionCPC-S and CPC-M, Version 1 0 and higher
AddressFF3 (ExtPort)# 
8# (0 or l)#
DescriptionThis setting determines if an extension can receive Call Waiting and Offhook
Voice Announcement (OHVA)
ProgrammingFF3 (l-16 or 
l-24)# 8# (0 or l)#
7+Extension Port
O=Off (Call Waiting/OHVA disabled)
CPC-S 1-16
CPC-M l-24
l=On (Call Waiting/OHVA enabled)
NotesConditions Under Which the Tone Is Not SentThe Call Waitingnotification tone cannot be sent to an extension...

Busy Override SendFF3Busy Override Send
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FF3 (ExtPort)# 9# (0 or l)#
DescriptionUse this program to determine whether to allow an extension to “barge in” on
calls that are in progress on other extensionsIf this feature is enabled, the
extension caller can join in on another extension s call all three parties will
be able to hear each other
ProgrammingFF3 (l-16 or 
l-24)# 9# (0 or l)#
/’f
Extension PortO=The extension cannot “barge in”CPC-S...

FF3Busy Override Receive
Busy Override Receive
Software Version
CPC-S and CPC-M, Version 1 0 and higher
Address FF3 (ExtPort)# 
lO## (0 or l)#
DescriptionThis program determines whether an extension’s calls can be “barged into ’ by
other extensions
ProgrammingFF3 (ExtPort)# 
lO# (0 or I)#
/f+Extension Port
O=Calls on this extension cannot be
CPC-S 1-16interrupted by a barge-in
CPC-M l-24
l=Calls on this extension can be
interrupted by a barge-in
Related ProgrammingAlert Tone for Busy Override 
& OHVA FFl...