Panasonic Dbs 824 Instructions Manual

Baud Rate (Maintenance Port)
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 9# 3## (l-4)##
DescriptionThe data transmission speeds between Maintenance serial port CN2 and
peripheral equipment can be set from 300 bits per second to 9600 bits per
second
Programming
FFl 2# 9# 3## (114)#
I=300 bps
2=1200 bps
3=24OO bps
4=9600 bps
NotesChecking Communications ParametersBe sure to properly set all
communication programming addresses when modifying any single address
valueCommunication...

Stop Bit Length (Maintenance Port)
Software VersionCPCS and CPC-M, Version 1 0 and higherAddress 
FFl 2# 9# 4-N (193)#
DescriptionThis program sets the length of the stop-bit parameter for a-ansmitted data
over Maintenance serial port CN2
Programming
FFI 2# 9# 4## (l-3)#
l=l bit
2=15 bits
3=2 bits
NotesChecking Communications ParameterBe sure to properly set all
communication programming addresses when modifying any single address
valueCommunication parameters for Maintenance are set with addresses
FF12#...

FFlData Length (Maintenance Port)
Data Length (Maintenance Port)
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress
FFl 2# 9# !% (3 or 4)##
DescriptionThis program sets the length of the transmitted data suing at 7 or 8 bits, over
Maintenance serial port CN2
Programming
I
3=7 bits
43 bits
NotesChecking Communications ParametersBe sure to properly set all
communication programming addresses when modifying any single address
value
Communication parameters for Maintenance are set with addresses...

Maintenance Serial POR Flow Control (XON / XOFF)FFlMaintenance Serial Port Flow Control (XON 
/ XOFF)
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 9# 6# (0 or l)#
DescriptionUse this address to determine whether the DBS 824 system will control the
flow of data between it and the device connected to the Maintenance serial
port 
(CN2)
‘ XON/XOFF’ (if activated in this address) is a software switch that will
temporarily stop the flow of data when the device s memory buffer...

FFlAutomatic Night 1 Mode Start Time
System Timers
Automatic Night 1 Mode Start Time
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3## 1# (OOOO-2359)#
DescriptionThis option sets a time for the DBS 824 to automatically switch from ‘Day
to ‘Night 1’ mode This program uses the 
24-hour time format.
Programming
To set the automatic Night 1 mode start time
FFl 3# l# (000012359)#
t
Night 1 Mode Start Time
(in 
24-hour format)
FFl 3# l# CONF ON/OFF
To disable the automatic Night 1 mode...

Attendant Hold Recall Timer for CO CallsFFlAttendant Hold Recall Timer for CO Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 2# (O-12)#
DescriptionThis timer determines how long a trunk call can be held by the attendant(s)
before it will recall
Programming
FFl 3# 2# (O-12)#
t
Recall Timer
(Default=l, see table below)
Table 1-7Recall timer v&es for attendant-held CO calls
Number
0
1
No recall
20 secondsValue
12-I 40secondsI
1 60 seconds
1 80 secondsI
1 100 seconds
6120...

FFlExtension Hold Recall Timer for CO Calls
Extension Hold Recall Timer for CO Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3## 3# (0012)#Description
This timer determines how long a hunk call will be held by an extensionbefore it will recall
Programming
FFl 3# 3## (0912)#
fRecall Timer (Default=7
see the following table)
Table I 8Recall tier values for extension-held CO calls
11220 seconds
12240 seconds
Related Programming
Extension Hold Recall Tier for Intercom CallsFFl 3#...

Attendant Transfer Recall Timer for CO CallsFFl
Attendant Transfer Recall Timer for CO Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 3# 4# (0-12)#
DescriptionWhen an attendant transfers a trunk call to an extension or hunt group, the
transferred call will recall to the attendant if it is not answeredThis timer
determines how long a transferred 
trunk call will go unanswered before it
recalls
Programming
FFl 3# 4## (0112)#
t
Recall Timer (Default=1
see the following table)...

FF?txtension I rawer Hecall I imer for CO Calls
Extension Transfer Recall Timer for CO Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higher
Address
FFl 3# 5# (o-12)#
DescriptionWhen an extension aansfers a trunk call to another extension or to a hunt
group, the transferred call will recall to the extension if it is not answered
This timer determines how long a transferred trunk call will go unanswered
before it recalls
Programming
FFl 3# 5# (0112)#
+
Recall Timer (Default=7
see the following...

Attendant Park Hold Recall TimerFFl
Attendant Park Hold Recall Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FF1 3# 6## (0-12)#
DescriptionAn attendant phone can use up to 10 Call Park Numbers (00-09) to hold trunk
callsThese park numbers can be assigned to an FF key or accessed by
placing a call on hold, then dialing 7501-7509
This program determines how long a parked 
call will be held before it recalls
Programming
FFl W 6## (0112)#
f
Recall Timer (Default=1
see the following...