Panasonic Dbs 824 Instructions Manual

FFlTransfer Ring Pattern
Transfer Ring Pattern
Software VersionCPC-S and CPC-M, Version 1 0 and higher
Address 
FFl 2# l# 28# (0-6)#
DescriptionThis program address allows you to choose a distinctive ringing pattern for
transferred calls on all DBS 824 phones
This setting will override theExtension Ring Pattern (set in address FF3 
ExtPort# 38#) when calls are
transferred to the extension
The ring pattern selected in this address will vary according to the type of
phone (Digital or Analog) connected to...

Page DurationFFl
Page Duration
SoftZ;are VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# l# 29# (0 or l)#
DescriptionThis address determines whether the DBS 824 system will automatically
close the paging circuit 60 seconds after a page is initiatedIf this address is
set to leave the paging circuit open indefinitely, the system will not
automatically close it (the paging person will close the circuit when he/she
hangs UP)
Programming
O=The page circuit remains open indefinitely
l=The paging...

FFlSLT DISA Ring Pattern
SLT DISA Ring Pattern
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FF1 2# l# 30## (0 or l)#
DescriptionDiffering ring patterns can be set for devices connected to SLTA ports that
receive inbound DISA calls
The pattern can be set to a one-second-on /
three-second-off ring burst, or it can follow any of the patterns found in the
normal Central Office transfer ring patterns (see “Transfer Ring Pattern’
program address FFl 2# l# 2%)
Programming
FFl 2# 1# 3O# (0 or...

SLT Disconnect DurationFFl
SLT Disconnect Duration
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# l# 31# (0-15)#
DescriptionThis program address determines the duration of the disconnect signal (open
loop) to the CO by an SLT extension port upon hangup
Sending this signalallows quick disconnect from third-party voice mail systems
The sending of the SLT disconnect signal can be enabled or disabled on an
extension-by-extension basis, using program address FF3 (ExtPort)# 
4%...

FFlCall Duration Timer
Call Duration Timer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 1# 32# (0,l or 2)#
DescriptionThis timer determines how long the system waits before displaying call
duration timing on the phone’s LCDFor example, if the timer is set to 5
seconds, the call duration timer will appear 5 seconds after an outgoing
number is dialed, or 5 seconds after an incoming call is answeredThis timer
allows Caller ID information (if available) to appear before the call...

Speed Dial ModeFFl
Speed Dial Mode
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# l# 33# (0 or l)#
DescriptionThis program determines the mode for speed-dialing (both Personal and
System)This speed-dial mode setting affects the range of speed-dial
numbers that can be created, 
as well as the number of digits in the speed-dial
numbers, as shown in the following table
Table l-4Speed-dial number ranges in Standard and Add-On modes--
CPC-s:
Standard ModeAdd-On Mode
SSD Number...

FFlAuto-Repeat Dialing Count
Auto-Repeat Dialing Count
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# l# 34# (0-15)#
DescriptionThis program determines the number of times the DBS 824 will automatically
redial a number (when Auto-Repeat Dialing is activated)
Programming
FFI 2# l# 34#I (0-l 5)#
t
O=System will not redial
l=System will redial one time
215 = System will redial this number of
times
(Default=15)
Related Programming
Wait Time for Auto-Repeat DialingFFl 3# 26#
Busy Tone...

Install OPL PortFFl
Install OPL Port
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2R l# 35# (0-2)#
DescriptionThis program enables or disables an OPL (Option Port Line) on CO ports I
and 2OPL can connect to external devices such as a fax or answering
machine in parallel to the DBS 824 system, sharing the CO ports with the
system
Programming
FFl 2# l# 35# (0,l or 2)#
f
O=No OPL port installed (default)
l=OPL is installed on CO port 1
2=OPL is installed on CO ports 1 and 2...

FFlMusic-On-Hold Sound Source
Music-On-Hold Sound Source
Soffware VersionCPC-M Only, Version 1 0 and higherAddress 
FFl 2# l# 36# (0,l or 2)#
DescriptionThis program address determines the sound source for Music-On-Hold (the
music or recording heard by a caller who is on hold)The sound source for Music-On-Hold can be the same as the source for
Background Music (the device plugged into CN6 phono-jack on the CPC M
card)Or it can be the internal 
sound source (from the tone generator on theCPC M card)
Or it...

EPI Audio ControlFFl
EPI Audio Control
Software VersionCPC-S Only (Version 1 0 and above)Address 
FFl 2# l# 37# (0 or l)#
DescriptionIf an external device is installed in the “EPA” phono-jack on the CPC-S card,
use this address to tell the system whether the device is an External Pager or
External Ringer
This address does not apply to the CPC-M card, which has two phono-jacks
(one specifically for each external device)
Programming
I
IFFl 2# l# 37# (0 or l)#
f
O=An External Paging device is
installed in...