Panasonic Dbs 824 Instructions Manual

FFlDay/Date Setting
Date and Time Settings
Day/Date Setting
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 1# l# (MMDDYY)#
DescriptionThis program sets the date in the DBS 824 system clock
The day and date are printed on the Station Message Detail Recording
(SMDR) printout. Proper LCR (Least Cost Routing) 
operatibn depends on
correct date settingsProper operation of peripheral equipment may also
depend on correct date settings
Programming
Month, day, and year in numeric format
(for...

Time SettingFFlTime Setting
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl l# 2# (HHMM)#
DescriptionThis program sets the time in the DBS 824 system clockThe time appearson key phones that have 
LCDs and is also included in SMDR call records
Note:Correct time settings are necessary for proper LCR (Least Cost
Routing) operation
Programming
FFl l# 2# HHMM#
tTime setting in 24-hour format
(for example 3 00 pm would be
entered as 1500) 

FFlCall Duration Display
General System Settings
Call Duration Display
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 1# I# (0 or l)##
DescriptionThe duration timing for outgoing CO calls is normally displayed on
telephones with 
LCDsThe DBS 824 can be programmed so that the callduration time is not displayed
NOTE: This setting does not affect SMDR recording of the call
Programming
FFl 2# l# l# (Oorl)#
O=Call duration is not displayed
l=Call duration is displayed
Related...

SMDR Start Timer for CO CallsFFl
SlVlDR Start Timer for CO Calls
Software VersionCPC-S and CPC-M, Version 1 0 and higher
Address
FFl 2# I# 2# (0, 1, or 2)#
DescriptionThis timer determines how long the system waits before starting an SMDR
record for the call (both outgoing and incoming)For example, if the timer is
set to 5 seconds, SMDR recording of call data will begin 5 seconds after an
outgoing number is dialed or 5 seconds after an incoming call is answered
For outgoing calls, the purpose of this...

FFlLeast Cost Routing (LCR) Access
Least Cost Routing (LCR) Access
Software Version@PC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 1# 3# (0 or l)#
DescriptionThis program specifies whether Least Cost Routing (LCR) is used when “9”
is dialed before making an outside call
Programming
FFl 2# 1# 3# (0 or l)#
t
0=“9” indicates a pooled-trunk call
1=“9” indicates an LCR call
Related ProgrammingForced Least Cost Routing
FF3 
(ExtPort)# 4#LCR Program Settings
FF8 (all)
NotesRestriction With Call...

Override Toll Restriction With SSD NumbersFFl
Override Toll Restriction With SSD Numbers
Software Version
CPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 1# 4# (SSD)#
DescriptionThis program allows you to set a range of system speed dial (SSD) numbers
that will override Toll Restriction Service (TRS) types 2-6
The number entered in this address is the lower boundary for speed dial
numbers that will override toll restrictions
In other words, 
all SSD numbers
higher than the one entered will also...

FFlSSD Display Restriction
SSD Display Restriction
Software VersionCPC-S and CPC-M, Version 1 0 and higher
Address
FFl 2# l# 5## (0 or l)#
DescriptionThis address determines whether the telephone’s LCD will display the actual
dialed digits for a certain range of SSD codes (80-89 for Standard mode, 160-
199 for Add-On mode)The default setting displays the dialed digits for
these SSD codesIf the display is disabled with this programming address,
the text assigned to the SSD code will display, but the...

Auto Flash RedialFFI
Auto Flash RedialSoftware Version
CPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# l# 6# (0 or l)#
DescriptionBy default, the REDIAL key sends a “flash” before redialing a number
When the DBS 824 is connected to a PBX sending a “flash” may place the
line to the PBX on hold, in this case, Auto Flash Redial should be disabled
Programming
FFl 2# 1# 6##(0 or l)#
f
O=REDIAL does not send “flash”
l=REDIAL sends “flash”
Related ProgrammingPBX Flash Timer 
FFl 3# 16#Trunk Port Type FF2...

FFlOne Touch Dial
One Touch Qial
Sofhnrare VersionCPCS and CPC-M, Version 1 0 and higherAddress 
FFl 2# l# 7# (0 or l)#
DescriptionThe One-Touch Dial feature enables users to dial an extension by pressing a
single programmable key
This feature is enabled regardless of the program
setting (One-Touch Dial cannot be deactivated)
Issued 3/l 195D BS 824- 1 O-400Page l-11 

On hook TransferFFl
Onhook Transfer
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FFl 2# 1# 8# (0 or l)#
DescriptionOnhook Transfer allows a user to transfer a call by placing the call on hold,
dialing the extension number, and then hanging up
If 
Onhook Transfer is
disabled, the user transfers the call by placing it on hold, dialing the extension
number, then pressing PROG, and hanging up
Programming
FFl 2# I# 8# (0 pr I)#
tO=Onhook Transfer is disabled
l=Onhook Transfer is enabled...