Panasonic Dbs 824 Instructions Manual

Intro-2DBS 824-l O-400
Issued 3/i /95 

Introduction to DBS 824 ProgrammingBefore You BeginBefore You Begin
This section describes preparations that should be completed before you start
programmingIf you are familiar with FF key programming for DBS
systems, you may begin programming as soon as these preparations have
been made
If you are new to DBS programming, be sure to read 
“Understanding FF
Key Programming” 
on page Intro-5 before you beginPreparations for Programming
Prior to programming the DBS 824 system, make sure you have completed...

Before You BeginIntroduction to DBS 824 Programming
Initializing New Systems
Before programming a newly installed DBS 824 system, set its programs to
the default values by performing the following procedureImportant: This procedure must be performed prior to programming theDBS 824 for the first timeFailure to initialize the CPC (Central Processing
Card) may cause operational problems
This initialization procedure can also be used when you want to return all
changed programs to the default values...

Introduction to DBS 824 ProgrammingUnderstanding FF Key ProgrammingUnderstanding FF Key ProgrammingProgram Structure
Program entries for the DBS 824 are divided into 10 primary groups (listed in
Table 1 below)Each programming group has its own Flexible Function (FF)
key on the phone(The FF keys can be identified by their LEDs on the left
side of the key 
) After you enter the programming mode (see “How to Enter
the Programming Mode”, 
next page), press the FF key of the desired group
to start programming...

Understanding FF Key ProgrammingIntroduction to DBS 824 ProgrammingCOWF Resets entry
to default setting
-VOL AMoves backward to the previous
programming levelFigure 2
Phone keys used in programming mode
/
FLASHStores your entry and moves
backward (decrements port number in
the same address, or decrements program
address number)
HOLDStores your entry and moves
forward (increments port number in
the same address, or increments program
address number)
*Storesyour entry and
moves backward (decrements
program...

iII~ruuuc;tw~I iu UD~ OLL) r IU~I~IIIIIIIIIYuIIue13tdlluiIty ri- r\cy r IUYI~IIIIIIII my
4 Press the desired FF keyNotes
l Name settings can only be programmed from the attendant telephone or a
DSS console connected to it
l When you enter the programming mode through an attendant phone, the
system will automatically change to the “Night” modeAfter exiting the
programming mode, the system will return to the appropriate Day/Night/
Night 2 mode according to the system clock and the mode’s start time
From a...

Default Program SettingsIntroduction to DBS 824 Programming
2 Press [FFl] ( System Program is displayed on line 1, SELECT
SUB MODE is displayed on line 2)
3Press1,#(SELECTTIMEMODEisdisplayedonline11DATE2TIMEis displayed on line 2)
4 Press 1# ( DATE SET MODE is displayed on line 1, MONTH/DAY/
YEAR is displayed on line 2)
5From the keypad, enter the new date in the following format
Enter month as MM
Enter date as DD
Enter 
year as YY
6 Press 
# to store the program changeThen press the [ON/OFF] key to...

Introduction to DBS 824 ProgrammingDefault Program Settings
Address
FFl 2# l# 6# (Oar I)#
FFl 2# I# 7; (0 or I)#
FF1 2# l# 8# (0 or l)#
FFl 2# l# 9# (0 or I)#
FFl 2# l# lO# (Oor l)#
!a 2# l# ll# (0 or l)#
FFl 2# 1# 12# (0 or l)##
FFl 2# l# 13# (Oor l)#
FFl 2# l# 14# (Oor l)#
FFl 2# l# 15# (Oor l)#
FFl 2# l# 16# (Oar l)#
FFl 2# l# 17# (0 or l)#
FFl 2# l# 18# (Oor l)#
Program
Default
Auto Flash Redial
REDIAL sends
flash
One Touch DialEnabled
Onhook TransferEnabled
Key Bank Hold
Disabled
Non-Appearing Trunk...

Default Program SettingsIntroduction to DBS 824 Programming
1
AddressProgramDefault
FFl 2# 2#. SMDR Data (Serial Port CNl)
FFI 2# 2# l# (0 or l)#Ptity Check (SMDR)On
FFl 2# 2# 2# (0 or l>#Odd/Even Parity (SMDR)Even
FFl 2# 2# 3# (1-4)#Baud Rate (SMDR)
9600 bps
FFl 2# 2# 4## (l-3)iYStop Bit Length (SMDR)1 bit
FFl 2# 2# 5# (3 or 4)#Data Length (SMDR)
8 bits
FF1 2# 2# 6# (0 or l)#SMDR Serial Port Flow Control (X-ON/X-OFF) No flow control
FFl 2# 2# 7# (0 or l>#SMDR Printing Mode 1 Outbound and Inbound...

Introduction to DBS 824 ProgrammingDefault Program Settings
AddressProgram
FFl 2# 9#Maintenance Dal-u (Serial Port CN2)
Default
i
FFl 2# 9# l# (0 or l)#Parity Check (Maintenance Port)OII
FFl 2# 9# 2# (Gor I)#
FFl 2# !a# 3# (l-q/#
Odd/Even Parity (Maintenance Port)
Baud Rate (Maintenance Port)
Even
9600 bps
jFF1 2# 9# 4#I (l-3)#1 Stop Bit Length (Maintenance Port)1 1 bit
FFl 2# 9# 5# (3 or 4)#
FFl 2# 9# 6# (0 or l)#
Data Length (Maintenance Port)8 bits
Maim Serial Port Flow Control (X ON/X OFF)No flow...