Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 4. Key Telephone FeaturesSection 700 - Operation
7.Press the HOLD key.
To assign System Speed Dial numbers to One-Touch keys:
1.Press the ON/OFF key.
l The phone issues intercom dial tone.
l The ON/OFF LED lights.
2.Press the PROG key.
3.Press the One-Touch key to be programmed.
4.Press the AUTO key.
5.Enter the System Speed Dial Number to be programmed.6. Press the HOLD key.
7.Press the ON/OFF key.
The ON/OFF LED goes off.
To chain two to five System’Speed Dial numbers to a single One
Touch...

Section 700 - OperationChapter 4. Key Telephone Features
7. 
Presy the AUTO key.
8.Enter the Speed Dial number for the telephone number.
9.Repeat steps 7 and I( for any additional Speed Diais to be chained.
IO. Press the HOLD key.
Il. Press the ON/OFF key.
The ON/OFF LED goes off.
To assign a DBS Feature Code to a One-Touch key:
1. Press the ON/OFF key.
l The phone issues intercom dial tone.
l The ON/OFF LED lights.
2. Press the PROG key.
3.Press the One-Touch key to be programmed.
4.Enter the feature...

Chapter 4. Key Telephone FeaturesSection 700 - Operation
6.Enter the telephone number.
7.Press the HOLD key.
8.Press the ON/OFF key.
The ON/OFF LED goes off.
To check a programmed One-Touch key:
1.Press the ON/OFF key.
l The phone issues intercom dial tone.
l The ON/OFF LED lights.
2.Press the CONF key.
“C” appears in the display.
3.Press the One Touch key to be checked.
The programmed data appears on the display.
4.Press the ON/OFF key.
l The ON/OFF LED 
.goes off.
l The date and time appears on the...

Section 700 - OperationChapter 4. Key Telephone Features
Table 4-9.One-touch access codes for trunk group numbersTrunk Group NumberCode Number to be entered
811
822
833
844
855
866
99.
lOne-Touch keys cannot be checked while Station Lockout is set.
One-Touch VM Access
(CPC-ALI and CPC-B Version 5.0 or higher)
DescriptionOne-Touch VM Access simplifies voice message retrieval for personal
mailboxes as well as attendant transfer of incoming calls to extension
mailboxes.For instructions on attendant usage of...

Chapter 4. Key Telephone FeaturesOperationSection 700 - OperationTo assign a voice mail key:
Note: You cannot program this feature if trunks are assigned to the key. First
clear the trunk assignments, then use the following procedures to assign the
VM key.
1.Press the ON/OFF key.l The phone issues intercom dial tone.
l The ON/OFF LED lights.
2.Press the PROG key.
3.Press the FF key, DSS key, or One-Touch key.
4. Press the CONF key.
5. Press the AUTO key.
6.Dial the voice mail pilot number.
7.If the key...

Section 700 - OperationChapter 4. Key Telephone Features
Considerations
lThe VM key can be used with the Panasonic Voice Mail or with third-party
voice 
[nail systems.
lIf the voice mail password is over three digits long, assign the password to
a personal or system speed 
dial number (00-99,000- 199 or 900-909).
When you use a speed dial number with the Panasonic Voice Mail, include
the pound 
(#) sign after the password. Excluding the # sign results in a 6-second delay before you are connected to the...

Chapter 4. Key Telephone FeaturesSection 700 - Operation
Onhook Dialing
(All Versions)Description
Onhook Dialing is a standard feature for DBS key phones. To dial onhook,
the user simply presses the 
ON/OFF key.Users can dial 
onhook using the dialpad, one-touch keys, or FF keys.
Pooled Trunk Access
(All Versions)Description
The DBS system supports up to 64 outside lines. These lines can be divided
into seven Pooled Trunk groups. If you assign an FF key as an 
MC0 or ML
key, the DBS can 
automatica!ly...

Section 700 - OperationChapter 4. Key Telephone Features
3.Dial the telephone number.
The number appears on the display.
4.Complete the call and replace the handset.The LED of the ML or 
MC0 key goes off.
To select a Pooled Trunk group that is not assigned to an FF key:
1.Press the ON/OFF key.l The phone issues intercom dial tone.
l The ON/OFF LED lights.
2.Enter the desired group number (8 l-86, 9).l The phone issues outside dial tone.
l “CO TALK #XX” (Where “XX” is the line number) appears on the...

Chapter 4. Key Telephone FeaturesSection 700 - Operation
lIf a ML or MC0 key is assigned line group number 9 and LCR has been
activated, LCR is selected automatically.
lPress the ML or MC0 key that flashes red to answer incoming calls.
lIf one group is set aside for data lines, this feature can be used when a line
is needed for operations such as data transmission via modem.
Prime Line Preference(All Versions)
DescriptionPrime Line Preference allows a user to place an outside call by simply
picking up...

Section 700 - OperationChapter 4. Key Telephone Features
Considerations
lTo make an Intercom Call, press the FF key programmed as an intercom
key and then dial the extension number.
lIf a member of the trunk group assigned to 
FFl is also assigned to a Direct
Line key, Prime Line Pickup will access the Direct Line key instead of
FFl.lPrime line preference should not be assigned to an SLT or DSLT
telephone.
Private Line
(All Versions). Description
An outside line can be reserved for exclusive access by...