Nortel Modular Ics 6.1 System Coordinator Guide

Answering calls / 51
P0603535  02 Modular ICS 6.1 System Coordinator Guide
provide one-press external autodial (Refer to Storing a 
number on a memory button for Autodial on page 87)
configure system-wide call appearances (SWCA) by 
assigning SWCA feature codes
Norstar T7316E telephone with added KIM
An extended KIM (eKIM) provides the same functionality as 
the OKIM plus the ability to support multiple lines, target lines 
and Hunt groups. A T7316E can support a maximum of four 
eKIMs. Your system can...

52 / Answering calls
Modular ICS 6.1 System Coordinator Guide P0603535  02
Cold starting the KIM
If your KIM fails, or if you want to erase programming on the 
KIM, there are two types of cold start.
For both types of cold starts:
1. Unplug and replug the T7316E line cable.
The telephone will restart and all the icons will flash. 
When the telephone icons stop flashing, the KIM module 
icons start flashing. 
2. At this point, do one of the following:
• KIM single-module cold start
If you just want to...

Answering calls / 53
P0603535  02 Modular ICS 6.1 System Coordinator Guide
 KIM multi-module cold start
If you want to cold start all the 
KIMs attached to your 
telephone, simultaneously 
press the top two buttons on the 
upper button set, and the 
bottom two buttons on the 
lower button set, as shown in 
the following diagram.
Customizing your KIM module
You can move external lines, target lines or hunt group 
appearances onto the eKIM by using ²¥¡Ú. See 
Moving line buttons on page 161.
Any of the...

54 / Answering calls
Modular ICS 6.1 System Coordinator Guide P0603535  02
You need the programming template found at the front of this 
guide. See A map for using programming on page 23 for more 
information.
1. Press ²¥¥ÛßßÜÝÝ.
2. Press ÛÜßÝß (the default System Coordinator 
password). Terminals&Sets displays.
3. Press ≠. Show set: displays.
4. Enter the DN number of the T7316E which is attached to 
the eKIM you want to program, then press OK
.
5. Press ≠. Capabilities displays.
6. Press ‘ two times...

Answering calls / 55
P0603535  02 Modular ICS 6.1 System Coordinator Guide
Release button
Pressing ¨ ends a call. You do not have to put the receiver 
down. ¨ also ends feature programming.
While you are on a call, do not press ¨ to end a feature you 
are using. If you do, you disconnect the call. Use ² instead.
Hearing aid compatibility
The receivers on all Norstar telephones and Business Series 
Terminals are compatible with hearing aids as defined in the 
FCC rules, Part 68, section 68.316. Not all...

56 / Answering calls
Modular ICS 6.1 System Coordinator Guide P0603535  02
Using Call Information for a particular call
²¡ÚÚ
Call Information allows you to see information about 
incoming calls. This information is more detailed than the Call 
Display information you can receive automatically. For 
external calls, you can display the name of the called-party 
telephone, telephone number, and the line name. For an 
internal call, you can display the name of the called-party 
telephone and the internal...

Answering calls / 57
P0603535  02 Modular ICS 6.1 System Coordinator Guide
Displaying Call Information before or after 
answering
To find out who is calling or to display information about your 
current call:
1. Press ²¡ÚÚ. 
2. Press £ or VIEW
 to display more information about an 
external call.
Call Display information becomes available between the first 
and second ring of an incoming call. If you answer before the 
Call Display information is available on your display, and you 
press ²¡ÚÚ, you see...

58 / Answering calls
Modular ICS 6.1 System Coordinator Guide P0603535  02
Making Call Display information appear 
automatically
Each telephone that rings for an external line can display Call 
Display information for that line. After the call is answered, 
Call Display information is always shown at the telephone that 
answered the call. Your installer or customer service 
representative can program telephones to have automatic Call 
Display.
This feature is not available to ISDN terminals.
Changing...

Answering calls / 59
P0603535  02 Modular ICS 6.1 System Coordinator Guide
5. Press ‘ four times.
6. Press ≠.
7. Choose a setting at 1stDisplay: using the CHANGE
 button. 
The choices are Name, Numbr or Line.
You may see Unknown name or Unknown number on the 
display if the information is not available from your telephone 
company. You may see Private name or Private number 
on the display if the caller blocks that information.
Picking up a call ringing at another 
telephone
You can pick up a call...

60 / Answering calls
Modular ICS 6.1 System Coordinator Guide P0603535  02
Answering any ringing telephone using Group 
Pickup
Your Norstar system can be divided into nine pickup groups. 
If you are a member of a pickup group, you can pick up a call 
that is ringing at any telephone in your pickup group.
1. Press ²àÞ.
Group Pickup cannot be used to retrieve a camped call.
If there is more than one incoming call at a telephone in a 
pickup group, a call ringing on an external line is answered 
first,...