Nortel Modular Ics 6.0 System Coordinator Guide

Tracking your incoming calls / 131
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Enabling and disabling autobumping
Your log has a set number of items that it can hold. When it 
becomes full, new calls cannot be logged. When your log is 
full, Autobumping automatically deletes the oldest Call Log 
item when a new call is logged.
Press ²¡ÚÞ to enable autobumping. 
Press ²£¡ÚÞ to disable autobumping.
Viewing your Call Log
To view your log:
1. Press ²¡ÚÛ. The display shows the number or 
previously...

132 / Tracking your incoming calls
Modular ICS 6.0 System Coordinator Guide P0992640 03
Erasing log items
You should routinely erase log items to make space for new 
items in your log.
1. Display the item you want to erase.
2. Press ³ or ERASE
.
3. Press ¨ to exit.
If you accidentally erase an item, you can retrieve it.
1. Press ³ or UNDO
 immediately.
2. Press ¨ to exit.
Making a call using Call Log
You may find it helpful to place calls from within your Call 
Log. The number stored for each call may...

Tracking your incoming calls / 133
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Creating a password to your Call Log
To access your Call Log through a password:
1. Press ²¥¡Þ. The displays reads New passwrd:.
2. Enter your four-digit password. The display reads 
Repeat New:.
3. Re-enter your four-digit password. The display reads 
Password changed, which confirms that your password 
has been assigned.
To enter Call Log using your password:
1. Press ²¡ÚÛ to enter Call Log. If you have 
programmed...

134 / Tracking your incoming calls
Modular ICS 6.0 System Coordinator Guide P0992640 03
Deleting an assigned password
Use this procedure when you want to delete an assigned 
password.
1. Press ²¥¡Þ. The display reads Old passwrd:.
2. Enter your old password. The display reads 
New passwrd:.
3. Press ³ or OK
. The display reads No pswd assigned, 
which confirms that your password has been deleted.
Programming a telephone to log calls automatically
Your installer or customer service representative can...

Tracking your incoming calls / 135
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Hold or release your active call before 
entering Call Log.
The external line is in use.
The repeat call counter, shown along with 
time and date, indicates the number of calls 
you received from the same caller.
This call was answered at another 
telephone (227).
This call was logged manually.
This call was not answered.
There are one or more items in your 
message waiting list, and there are one or 
more new items...

136 / Tracking your incoming calls
Modular ICS 6.0 System Coordinator Guide P0992640 03
Using external Voice mail
If you subscribe to a voice message service outside your 
office, you can access that service through your Norstar 
system. Your installer or customer service representative 
programs your Norstar telephone to indicate when you have a 
voice message waiting on a particular line. 
To find out if your external voice message service works with 
Norstar, or if you have any problems with your...

P0992640 03 Modular ICS 6.0 System Coordinator Guide
Customizing your telephone
Finding out what a button does using Button Inquiry
²¥â
You can use this feature to check the function of any line, 
intercom, or programmed button on your telephone. 
On the M7100 and the T7100 sets, Button Inquiry shows your 
internal number followed by the function assigned to your 
single memory button.
Displays
The display shows the number and name 
of the line. Press 
SHOW to view the 
redirection status of the line....

138 / Customizing your telephone
Modular ICS 6.0 System Coordinator Guide P0992640 03
Changing the set display contrast
Use this feature to adjust the contrast on your set.
1. Press ²¥à.
2. Press a number on the dialpad to choose the contrast level 
you prefer. 
On a two-line telephone, you can use the UP
 and DOWN display 
buttons to adjust the contrast. The number of contrast levels 
available varies from one telephone model to another.
Changing the language on the display
You can select the language...

Customizing your telephone / 139
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Programming a feature code onto a memory button
You can program a feature code onto a memory button. In 
some cases, pressing the button a second time cancels the 
feature.
Programming feature buttons
Any memory button not programmed as an external or internal 
line, target line, Answer button, or Handsfree/Mute button, is 
available for features.
1. Press ²¥Ü.
2. Press the memory button you want to program with a...

140 / Customizing your telephone
Modular ICS 6.0 System Coordinator Guide P0992640 03
Displays
The name of the feature assigned to a button 
is displayed when you press the button.
 
SHOW appears when there is more 
information available. Press 
£ or SHOW for 
additional information.
If you are checking a speed dial button, enter 
the three-digit speed dial code that you want 
to check.
Enter the feature code, or press ¨ or QUIT 
to quit programming or CLEAR to clear the 
numbers you have entered. The...