Nortel Modular Ics 6.0 System Coordinator Guide

Programming Hunt Groups / 171
P0992640 03 Modular ICS 6.0 System Coordinator Guide
4. Press ‘ until the display shows System 
prgrming.
5. Press ≠. The display shows Hunt groups.
6. Press ≠. The display shows Show group.
7. Enter the Hunt Group number you want to program (1-30).
8. Press ≠. The display shows Member DNs:.
9. Press ‘ until the display shows Q Timeout:.
10. Press CHANGE
 to set the queue time-out: 15, 30, 45, 60, 
120, 180.
11. Press ¨ to exit or ‘ to continue programming.
Programming the...

172 / Programming Hunt Groups
Modular ICS 6.0 System Coordinator Guide P0992640 03
6. Press ≠. The display shows Show group.
7. Enter the Hunt Group number you want to program (1-30).
8. Press ≠. The display shows Member DNs:.
9. Press ‘ until he display shows Overflow:.
10. Press CHANGE
 to change the overflow position.
11. Enter the new overflow position.
12. Press ¨ to exit or ‘ to continue programming.
Setting the name
This setting allows you to program the Hunt Group name, such 
as Service or Sales....

Programming Hunt Groups / 173
P0992640 03 Modular ICS 6.0 System Coordinator Guide
11. Use the dialpad to enter the name of the Hunt Group.
12. Press ‘ to store the name.
13. Press ¨ to exit or ‘ to continue programming. 

174 / Programming Hunt Groups
Modular ICS 6.0 System Coordinator Guide P0992640 03 

P0992640 03 Modular ICS 6.0 System Coordinator Guide
Using the Hospitality features
This section describes the Hospitality Services feature which 
is used to administer room and alarm services in small to 
medium-sized facilities such as hostels, motels, or hospitals.
There are three types of sets that make up this type of system:
Common set—this telephone can be found in the lobby, 
office, or common area, and is not associated with a room. 
This type of set cannot access all of the features.
Room...

176 / Using the Hospitality features
Modular ICS 6.0 System Coordinator Guide P0992640 03
3. Press ÛÜßÝß (ADMIN). The display shows 
Terminals&Sets.
4. Press ‘ until the display shows Hospitality.
5. Press ≠.
6.Desk pswd:4677 displays.
7. Press CHANGE
. 
8.New pswd: displays
9. Enter a new password, then press OK
.
Cond pswd
Change this password frequently, to maintain security.
1. Place the appropriate programming overlay on the set you 
are using to do programming.
2. Press ²¥¥ÛßßÜÝÝ (CONFIG). The...

Using the Hospitality features / 177
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Room/desk information
There are two aspects to programming room information. 
First you must program specific DNs to a specific room 
and set up the room occupancy filters, which determine 
what types of calls can be made from a room set at various 
states of occupancy. 
Note: You can assign up to five DNs to the same room 
number.
Then you need to administer the room occupancy and state 
of the room.
Programming...

178 / Using the Hospitality features
Modular ICS 6.0 System Coordinator Guide P0992640 03
9. Press CHANGE and enter the room number, then press OK to 
accept the change.
10. Repeat step 6 for all the sets you want to assign.
11. Press ‘. Adm pwd req’d:Y displays
12. Press CHANGE
 and choose Y or N, depending on your 
security requirements.
Call restrns
You can set up call restrictions based on room occupancy 
states. This setting affects the Room occupancy feature.
1. Place the appropriate programming...

Using the Hospitality features / 179
P0992640 03 Modular ICS 6.0 System Coordinator Guide
The table below shows an example of a call restrictions 
setup.
Service times
You can set the time when occupied rooms change from 
Service done to Service required. This setting affects the 
Room condition feature.
1. Place the appropriate programming overlay on the set you 
are using to do programming.
2. Press ²¥¥ÛßßÜÝÝ (CONFIG). The 
display shows Password:.
3. Press ÛÜßÝß (ADMIN). The display shows...

180 / Using the Hospitality features
Modular ICS 6.0 System Coordinator Guide P0992640 03
Using the room/set programming
This section describes how the room occupancy and room 
condition settings are used.
Setting dialing filters by room state
1. Press ²¡àá.
2. Enter the Desk admin password if you are prompted for a 
password.
The set displays: Oc of rm#::
3. Enter the room number and press OK
.
The set displays rrrrr:Vacant.
4. Press the CHANGE
 display key and select the required status 
for the room...