Nortel Modular Ics 6.0 System Coordinator Guide

Customizing your telephone / 151
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Moving line buttons
You can move external lines to different buttons on your 
telephone to arrange your lines in the way that makes the most 
sense to you.
You cannot move intercom, answer or Handsfree/Mute 
buttons onto a CAP module.
1. Press ²¥¡Ú. 
2. Press the button you want to move the line from.
3. Press the button you want to move the line to.
Displays
The two buttons you selected have 
exchanged position.
You...

152 / Customizing your telephone
Modular ICS 6.0 System Coordinator Guide P0992640 03
Changing the type of ring
You can choose one of four distinctive rings for your 
telephone. This makes it easier to identify your telephone in an 
open office.
1. Press ²¥ß.
2. Press Ú, Û, Ü, Ý, or NEXT
. You hear the selected 
ring for two seconds.
3. Repeat until you hear the ring you prefer, then press ³ 
or OK
.
Adjusting the Ring volume
Use this feature to adjust the ring volume.
1. Press ²¥¡â. The telephone...

Customizing your telephone / 153
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Restoring the messages and calls indication
Press ²£¡âß. 

154 / Customizing your telephone
Modular ICS 6.0 System Coordinator Guide P0992640 03 

P0992640 03 Modular ICS 6.0 System Coordinator Guide
User Preferences
The User Preferences section of programming allows you to 
program memory buttons, speed dial codes and other settings 
for any Norstar telephone on the system.
For example, an employee may want to have the Do Not 
Disturb feature programmed onto a memory button or create a 
speed dial code. Instead of programming from the each 
specific set, you can go into programming on the telephone 
nearest you to make the change.
Using User...

156 / User Preferences
Modular ICS 6.0 System Coordinator Guide P0992640 03
connected at that internal number. You cannot make 
changes if the model is Other.
3. Press ‘ to move through all the subheadings in 
User Preferences.
User Preferences programming is available under the heading 
User Prefernces in Terminals&Sets in the main body of 
programming.
Sub-headings in User Preferences
Changing button programming
Press ≠ at Button prgrming. The display shows the 
number of buttons on the telephone. An...

User Preferences / 157
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Use the display buttons to change the programming for a 
button. 
Note: User Preferences programming cannot change the 
buttons that are used by lines, intercom, and the handsfree 
feature.
The display buttons used in button programming.
Changing User Speed Dial
1. Press ≠ at User Speed Dial. The display shows 
the number of speed dial codes that are available.
2. Press ‘ to see the first speed dial code (256).
3. Press ‘ to move...

158 / User Preferences
Modular ICS 6.0 System Coordinator Guide P0992640 03
5. Press CHANGE and enter the telephone number the same 
way you would dial it on the telephone.
6. Press OK
.
7. Press ‘ and choose the line (or enter a code for a 
line pool) the speed dial code should use.
Use the line pool code to select a particular line pool for use 
with Speed Dial. If you select Use routing tbl, a line or pool 
is chosen by the routing programming according to the initial 
digits in the number.
The route...

User Preferences / 159
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Changing the language used on the display
Press CHANGE
 at Language: until you see the language you 
want to use. See Changing the language on the display on page 
138. 
Making the display lighter or darker
Press CHANGE
 at Display cntrst until you see the value you 
want to use.
The display contrast on the telephone you are using for the 
programming session does not change when you are 
programming another telephone.
Changing...

160 / User Preferences
Modular ICS 6.0 System Coordinator Guide P0992640 03
A feature is stored on this button. Pre ss 
≠  to see the feature code. A full list 
of names and codes for features is included 
in the index.
Shows the feature code stored on a button. 
Press 
≠  to see the button number 
and feature name.
The button has a telephone number stored 
on it. Press 
≠to see the rest of the 
number.
The autodial is an external number. Press 
≠ to see what line or pool the call is 
programmed to go...