Nortel Modular Ics 6.0 System Coordinator Guide

Using the Hospitality features / 181
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Using the room set:
1. Press ²¡àßon a digital set 
or ˚¥¡àßon an analog set.
2. At the prompt, set the status of the room.
Note: You may be required to enter a Room condition 
password.
Press Ú to indicate Set to srv done.
Press Û to indicate Set to needs srv.
The set displays the selected prompt.
3. Press ¨ to exit.
Using the admin set:
1. Press ²¡à¡.
2. Enter the Desk admin password if you are prompted for a...

182 / Using the Hospitality features
Modular ICS 6.0 System Coordinator Guide P0992640 03
Programming the alarm feature
If you want to allow the room sets to program wake-up alarms, 
there are a couple of program settings that need to be entered.
1. Place the appropriate programming overlay on the set you 
are using to do programming.
2. Press ²¥¥ÛßßÜÝÝ (CONFIG). The 
display shows Password:.
3. Press ÛÜßÝß (ADMIN). The display shows 
Terminals&Sets.
4. Press ‘ until the display shows Hospitality.
5. At...

Using the Hospitality features / 183
P0992640 03 Modular ICS 6.0 System Coordinator Guide
18. Press CHANGE to choose either Y (yes) or N (no). 
19. Press ¨ to exit or ‘ to continue programming.
Using the Administration set to control alarms
Only a Hospitality Services set can use this alarm 
administration feature. This feature is also associated with a 
room number, and cannot be used on common sets.
Use this feature to:
query a current or last alarm time set for a room
assign an alarm time for any...

184 / Using the Hospitality features
Modular ICS 6.0 System Coordinator Guide P0992640 03
If the clock uses a 12-hour format, enter the time, then 
when the set displays: hh:mm AM or PM?, press AM
 or PM. 
The set displays: Alarm ON hh:mm.
5. Press ¨ to exit.
Using the alarm
To set an alarm on a digital telephone:
1. Press ²¡àÞ.The displays shows Alrm:07:00 
OFF
2. Do one of the following:
If the alarm is correct, press ON/OFF
.The set displays: 
Alrm:07:00am ON. Press DONE
 to exit.
If you need to...

Using the Hospitality features / 185
P0992640 03 Modular ICS 6.0 System Coordinator Guide
To enter a new time, repeat the above steps and enter a new 
time. This overwrites the existing entry.
Canceling an alarm
Canceling the alarm time for any set cancels the alarm time for 
all the sets in the same room.
Digital set: Press ²£¡àÞ.
Analog set: Press ˚£¡àÞ.
Turning off an alarm
When the alarm rings, the user can release the ring by doing 
one of the following, depending on the type of set in the room:...

186 / Using the Hospitality features
Modular ICS 6.0 System Coordinator Guide P0992640 03 

P0992640 03 Modular ICS 6.0 System Coordinator Guide
Telephone features
Installing Business Series Terminals
If you are connecting a Business Series Terminal for the first 
time, refer to the following illustrations as a guide.
Installing the Business Series Terminal connections
Installing to a desk jack 

188 / Telephone features
Modular ICS 6.0 System Coordinator Guide P0992640 03
Mounting a Business Series Terminal on the wall
Mounting a Business Series Terminal using the stand
Installing without the angled base
Mount the keystation onto the
    screws and slide it down.Mount the stand as shown and
insert screw. Use the screw that
came with your keystation.
 
Connect line cord to 
wall jack. Connect cords to the keystation,
    refer to cord connections
  Tighten screws for a secure fit. 

Telephone features / 189
P0992640 03 Modular ICS 6.0 System Coordinator Guide
Installing Norstar telephones
If you are connecting a Norstar telephone for the first time, 
refer to the following illustrations as a guide.
Installing a Norstar telephone
Connect to 
jack wired from
distribution block
Connect to 
receiver 

190 / Telephone features
Modular ICS 6.0 System Coordinator Guide P0992640 03
Mounting a Norstar telephone on the wall
12
34
56