Nitsuko 124i/384i Software Manual

Programming (Cont’d)
Related Features
Refer to the Tenant Service Feature Interaction table on the previous pages.
Operation
Refer to the features listed in the Tenant Service Feature Interaction table.
No Yes
Stop
In Program 1002,
assign extensions to
tenants.
In Program 0904,
assign trunks to
tenants. An extension in one tenant group
can have the same number as an
extension in another group.
In Program
0301, enter 0.In Program
0301, enter 1.
Should user in one
tenant be able to place
Intercom calls...

Tie Lines
Description
 124i Available with EXCPRU PCB only.
DTMF tie lines require a DTDU PCB. 384i Available.
Customizing CODEC Gain Type
transmit and receive levels and Tone
Detection Setup requires Base 2.13,
EXCPRU 2.18 or higher.Customizing CODEC Gain Type
transmit and receive levels and Tone
Detection Setup require system
software 3.04 or higher.
- Enhanced Answer Supervision
requires Base 2.13, EXCPRU 2.18 or
higher. See page 844.- Enhanced Answer Supervision
requires system software 3.05.15 or...

Description (Cont’d)
•Direct Trunk Access
This option allows tie line callers to directly access a trunk for an outside call by dialing #9 and the
trunk’s number. Like Trunk Group Access, this bypasses the remote system’s Trunk Group Routing/ARS.
Any toll charges are incurred by the remote system.
•Forced Trunk Disconnect
The Forced Trunk Disconnect option allows a tie line caller to disconnect (release) another extension’s ac-
tive outside call. The tie line caller can then place a call on the released...

Programming
StopIn 0901 Items 14-17, enter
5 for tie line service type.
Are all your tie trunks of
the same type - with the
same signaling
requirements?In 0905, assign all tie trunks to
the same group. No other
trunks should be in the group.In 0905, assign each
unique type of tie trunk
to its own trunk group.
Does tie trunk
have DP or DTMF
inbound signaling?In 0901:27, enter 0 for
DP incoming signaling.In 0901:27, enter 1 for
DTMF incoming signaling.
In 0133, make sure the Tie
Line Timers are compatible...

Programming (Cont’d)
Continued
from
previous
page.
Do you want tie line to
absorb (ignore) first
incoming digit?In 0412:1, enter 0.
Should tie line user be
able to dial 9 for Trunk
Group Routing or ARS?In 0412:2, enter 1.In 0412:2, enter 0.
Should tie line user be able
access a trunk group by dialing
804 and the groups number?In 0412:3, enter 1.In 0412:3, enter 0.
Should tie line user be
able to use Common
Abbreviated Dialing?In 0412:4, enter 1.In 0412:4, enter 0.
Should tie line user be
able to dial...

Programming (Cont’d)
Continued
from
previous
page.
Is the DTMF
Receiver Active
Time adequate?In 0405 Item 17,
change the DTMF
Receiver Active Time.
In 2302, assign a tie lines
Class of Service (1-16) for
options in 0412.Did you enable dial 9
trunk access for tie
line in 0412 Item 27?In 2304, set the trunk
group route (1-64, set in
0906) the tie line seizes
when the user dials 9.
In 0906, program Trunk Group
Routing (1-64). (If the system
has ARS enabled, dialing 9
accesses ARS instead.)
Do you want to...

Programming (Cont’d)
Continued
from
previous
page.
In 0116 Items 1-10, set
the DTMF criteria for tie
line calls for compatibility
with the telco.
Is the CODEC Gain
(amplification) adequate
for the tie Line?In 0901 Item 3, assign
a different CODEC
Gain Type.
If required, in 0117
customize the CODEC
Gain Type transmit and
receive levels.
Should users be able
to place outgoing calls
on tie line?In 0901 Item 31,
enter 1.
In 0901 Item 31,
enter 0.
Stop
No
Yes
No
Yes
Features N-Z
Tie Lines
92000SWG08   Issue...

Programming (Cont’d)
➣
0116 - Tone Detection Setup
Use Items 1-10 to set the DTMF criteria for tie line calls.
➣0117 - Trunk CODEC Gain Type Settings
Customize the transmit and receive levels of the CODEC Gain Types assigned in 0901 Item 3.
➣0133 - Tie Line Timers
Make sure the Tie Line Timer settings are compatible with your local telco.
➣0303 -  DTMF and Dial Tone Detection Circuit Setup
If the system has DTMF tie lines, be sure to reserve at least one DTU block for analog trunk DTMF re-
ception (type...

Programming (Cont’d)
➣
2304 - Tie Line Route
Use this program to assign the trunk group route (1-64) chosen when a user seizes a tie line and dials 9.
Set Trunk Group Routing in program 0906.  If the system has ARS, dialing  9 accesses ARS.
➣2305 - Tie Line Outgoing Call Restriction
This program lets you build a restriction matrix for trunk calls placed over a tie line.  For each tie line
trunk group (1-128), enable (0) or disable (1) outgoing access  to each CO trunk group.
➣2306 - Tie Line Toll...

Operation (Cont’d)
To place a call over a specific tie line:
1. Press idle CALL key and dial #9.
2. Dial tie line number (e.g., 005 for line 5).
3. Dial number.
OR
1. Press tie line key (PGM 1006 or SC 851:  1 to 128).
2. Dial number.
After calling the remote system, you may be able to:
•Dial 9 to place an outside call through the remote system.
•Dial Service Code #9 + a trunk number to place outside calls over a specific trunk.
•Use the remote system’s Common Abbreviated Dialing.
•Call the remote...