Nitsuko 124i/384i Software Manual

Program - 2404 ANI/DNIS Service Options
Option Description Range Default
Item 4Route Data
The option sets how the system uses the route data
(gathered in Item 3) to route incoming ANI/DNIS calls.
The choices are:
0 = Dial Data (From Caller ID Table Name Field)
The system uses the Caller ID Table specified in Item 7
below for inbound routing. The data in the Caller ID
Table Name field is used as dial data for routing. For this
entry, the Name field entry can be an extension number, a
Department Group...

Program - 2404 ANI/DNIS Service Options
Option Description Range Default
Item 6ANI Caller ID Table Setup
Use this option to define which part of the Caller ID
Table set up in Program 2402 the system will use for
ANI/DNIS Caller ID lookups. This is required if Items 4
and 5 above are 1 (Caller ID On). When you specify a
starting address and length, the system uses that part of
the table for lookups.Start Address
= 000-999
Length =
0000-1000Start Address
= 0000
Length = 1000
Item 7ANI Routing Table Setup...

Programming (Cont’d)
➣
2601 - T1 Setup
Designate each T1 trunk circuit for either loop start (0) or ground start (1) operation. For ANI/DNIS, the
recommended setting is 0 (loop start).
➣2602 - T1 Clock Source
For each PCB, set the clock source for internal system clock (1) or external telco clock (2). For
ANI/DNIS, the recommended setting is 2 (external).
ANI/DNIS Routing to the VAU Automated Attendant
Beginning with 384i software version 3.06.09 and 124i EXCPRU 4.02 software, ANI/DNIS calls can route...

Programming (Cont’d)
Method C
When the trunk rings in and 2404 Item 3 = 0, the system looks to 2205 for routing data. If 2205 = 0 for the
trunk, the system uses the error handling specified in 2404 Item 8. If 2205 = 01-16, the system routes the caller
to the VAU Automated Attendant and plays the indicated message.
➣2205 - OPA Message Assignment
Make sure there is an OPA Message assigned (01-16) for each trunk you want the OPA Automated Atten-
dant to answer.
➣2404 - ANI/DNIS Service Options, Item 3:...

Tandem Trunking (Unsupervised Conference)
Description
 124i The system allows either 8 four-
party conferences or 4 eight-party
conferences. 384i Each DTU-A/C allows either 4
four-party conferences or 2 eight-
party conferences per PCB.
- Enhanced Tandem Trunking requires
Base 2.13, EXCPRU 2.18 or higher.- Enhanced Tandem Trunking requires
system software 3.05.10 or higher.
Tandem Trunking allows an extension user to join two outside callers in a trunk-to-trunk Conference. The exten-
sion user can then...

Programming (Cont’d)
Enhanced Tandem Trunking
B A
Stop
In 0419 Items 1 and 2, enter 1.
In 0406 Item 120, enter 1 to enable
Forced Trunk Disconnect.
In 0419 Item 1, enter 1.
In 0402 Item 6, enter 1 to assign
CONF (TRF) for Conference.Do you want Method A
(From Conference) or
Method B (On Hang Up)?
NoYes
If required, change the CODEC Gain Type
transmit and receive levels in 0131.
In 0901 Item 23, assign a new
CODEC Gain Type for
Unsupervised Conference calls.When in a tandem call, are the
trunkss gains...

Programming (Cont’d)
Tandem Trunking in Older Systems
Stop
NoYes
If required, change the CODEC Gain Type
transmit and receive levels in 0131.
In 0901 Item 23, assign a new
CODEC Gain Type for
Unsupervised Conference calls.When in a tandem call, are the
trunkss gains (volumes)
adequate?
In 0402 Items 2 and 6, enter 0. Tandem Trunking SectionConference Section
Stop
In 0901 Item 31, enable (1) loop supervision for each
trunk that should be able to use Tandem Trunking. No
Yes No
Yes
In 1006, assign a...

Programming (Cont’d)
Enhanced Tandem Trunking Method A — Tandem Trunking from Conference
➣0131 - Unsupervised Conf. CODEC Gain Setup
Set up the CODEC Gain Types for trunks in an Unsupervised Conference. Assign Gain Types to trunks
in 0901 Item 23.
➣0302 - Music on Hold and Conference Setup, Item 2: Conference Setup
Set the Conference mode of each DTU-A or DTU-C PCB.  The system allows either 4 four-party confer-
ences (0) or 2 eight-party conferences (1) per PCB.
➣0308 - Conference Circuit Setup
Assign...

Programming (Cont’d)
Tandem Trunking in Older Systems
➣0131 - Unsupervised Conf. CODEC Gain Setup
Set up the CODEC Gain Types for trunks in an Unsupervised Conference. Assign Gain Types to trunks
in 0901 Item 23.
➣0302 - Music on Hold and Conference Setup, Item 2: Conference Setup
(124i Only) Set the Conference mode of the system.  The system allows either 8 four-party conferences
(0) or 4 eight-party conferences (1).
(384i Only) Set the Conference mode of each DTU-A or DTU-C PCB.  The system allows...

Operation
Method A — Tandem Trunking from Conference
To set up a Tandem Call:
1. Place or answer first trunk call.
2. Press CONF (TRF) key.
3. Place or answer second trunk call.
4. Press CONF (TRF) key twice.
This sets up a Conference between you and both outside parties.
5. Press Transfer key (PGM 1006 or SC 851: 1077).
OR
Press HOLD and dial #8.
The line keys for the trunks blink (green) as long as the Unsupervised Conference Continues.
To end the Tandem Call:
1. Press either flashing line key.
The...