NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual S22 – 563
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSGeneral
	This feature is available to all Multiline Terminals.
	Stored Hookflash is effective on Loop Start trunks when the system is
installed behind a PBX or Centrex system. 
	A hookflash can be stored in System and Station Speed Dial buffers.
	The LCD display for a Stored Hookflash shows / during programming
and use of the Speed Dial buffer.
	A Stored...

July 2003 NEC Business Solutions Ltd
564 – S22Stored Hookflash
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual S23 – 565
Doc. No. 8201 - Release 1.0
July 2003
Synchronous RingingS-23
FEATURE 
DESCRIPTIONThe Synchronous Ringing feature synchronises CO/PBX incoming ringing
with the incoming ringing pattern from a Central Office.
SYSTEM 
AVAILABILITYTerminal Type
All terminals except Single Line Telephones connected to AP(R)-R( ) Unit.
Required Components
None.
OPERATING 
PROCEDURES
SERVICE 
CONDITIONS
	Synchronous Ringing is programmed system-wide.
	Synchronous Ringing is not...

July 2003 NEC Business Solutions Ltd
566 – S23Synchronous Ringing
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual S24 – 567
Doc. No. 8201 - Release 1.0
July 2003
System Data Up/Down 
LoadS-24
FEATURE 
DESCRIPTIONThe System Data Up/Down Load feature, included with the NEC
Maintenance Access Terminal (MAT) Software, transfers Station Speed Dial
data, System Speed Dial data, and all System Data from/to a Pentium
1-
compatible PC. System Data Up/Down Load can be performed from a local
or remote location.
SYSTEM 
AVAILABILITYTerminal Type
Not applicable.
Required Components
Local...

July 2003 NEC Business Solutions Ltd
568 – S24System Data Up/Down Load
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONS	This feature allows System Data to be programmed from a PC
connected to the system.
	Items that can be transferred:
1. Complete System Data 
2. Partial System Data 
 All System Data Blocks
 Tenant Blocks (All/Tenant/Individual Tenant)
 Trunk Blocks (All Trunk/Individual Trunk)
 Terminal Blocks (All Terminal/Individual Terminal)
 Trunk Route Blocks
3. System Speed Dial
4....

Features and Specifications Manual T1 – 569
Doc. No. 8201 - Release 1.0
July 2003
Tandem Switching of 
4-Wire E&M Tie LinesT- 1
FEATURE 
DESCRIPTIONThe Tandem Switching of 4-wire E&M Tie Lines feature allows connecting
E&M Tie Lines to other trunks through the system without help or
supervision from an internal station to allow distant-end system users to
remotely access trunks. Pad control is provided on the TLI(2)-U(  ) ETU by a
programmable transmission pad to adjust to the line loss levels of the...

July 2003 NEC Business Solutions Ltd
570 – T1 Tandem Switching of 4-Wire E&M Tie Lines
Doc. No. 8201 - Release 1.0
July 2003
General
	The Xen IPK Expanded system can handle a maximum of 32
simultaneous tandem calls.
	The Xen IPK Basic system can handle a maximum of 8 simultaneous
tandem calls.
	After a tandem connection is completed, the trunks disconnect (restore
to idle) when either party hangs up and a disconnect signal is received
by the corresponding trunk or the Automatic Disconnect Timer...

Xen IPK Features and Specifications Manual
Features and Specifications Manual T1 – 571
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BSCard Interface Slot Assignment 7-1
¶+ALNTie Line Networking Tandem Connection 
Assignment5-01
¶+BCTTrunk Internal Transmit Pad Selection 3-29
¶+BCTTrunk Internal Receive Pad Selection 3-30
¶+BCTTrunk External Transmit Pad Selection...

July 2003 NEC Business Solutions Ltd
572 – T1 Tandem Switching of 4-Wire E&M Tie Lines
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK