NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual S18 – 553
Doc. No. 8201 - Release 1.0
July 2003
	This feature cannot be used to relocate DSS Consoles because
consoles are not assigned station numbers. If Station Relocation is
performed for a station that has an associated DSS Console, the
station is relocated but not the DSS Console.
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line...

July 2003 NEC Business Solutions Ltd
554 – S18Station Relocation
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual S19 – 555
Doc. No. 8201 - Release 1.0
July 2003
Station TransferS-19
FEATURE 
DESCRIPTIONThe Station Transfer feature allows any station user in the system to
transfer any call to any other station. Outside calls can be transferred to
Multiline Terminals without the direct line appearance. To initiate Call
Transfer, press the Transfer key on a Multiline Terminal or use the
hookswitch on a Single Line Telephone. The transfer is completed by going
on-hook on a Multiline...

July 2003 NEC Business Solutions Ltd
556 – S19Station Transfer
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSData Assignment
	This feature can be disallowed in System Programming system-wide
(default: transfer is allowed).
	A recall timer for a transferred call can be programmed in System
Programming. Any station with an Attendant Add-On Console
assigned to it recalls using the Attendant Add-On Console Transfer/
Camp-On Recall Timer. A station without an Attendant Add-On
Console recalls using...

Features and Specifications Manual S20 – 557
Doc. No. 8201 - Release 1.0
July 2003
Step CallS-20
FEATURE 
DESCRIPTIONIf a caller receives a call waiting tone during an internal call, the caller can
access the next higher station number in the same 10s group (e.g., 10~19,
20~29, or 110~119, 220~229) by dialling 2 (default).
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING 
PROCEDURES
1. Dial B (set at default). 
2. The next higher available station number is called.
1....

July 2003 NEC Business Solutions Ltd
558 – S20Ste p Ca ll
Doc. No. 8201 - Release 1.0
July 2003
	If Station 109 is call forwarded to Station 121, and Station 121 is busy,
and a call is made to Station 109 which forwards to Station 121, a call
waiting tone is received. If Step Call is used, the call skips to Station
122, if available.
	When using the Step Call feature, the system skips stations that
are busy.
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07...

Features and Specifications Manual S21 – 559
Doc. No. 8201 - Release 1.0
July 2003
Store and RepeatS-21
FEATURE 
DESCRIPTIONThe Store and Repeat feature allows a Multiline Terminal user to store any
telephone number in memory (while talking on a CO/PBX line) for later use.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals.
Required Components
None.
OPERATING 
PROCEDURES
1. Press T.
2. Dial 
G.
3. Dial the desired number to be stored in memory.
4. Press
T.
5. Restore the handset or press
P....

July 2003 NEC Business Solutions Ltd
560 – S21Store and Repeat
Doc. No. 8201 - Release 1.0
July 2003
General
	The Store and Repeat and the Save and Repeat features cannot be
used simultaneously from a Multiline Terminal. The same memory area
is shared by both features. 
	The stored number is retained in memory by the memory backup
battery.
	A new number can be saved over the last Store and Repeat number.
	When entering a Store and Repeat number, the Conference key can
be used to backspace and erase...

Features and Specifications Manual S22 – 561
Doc. No. 8201 - Release 1.0
July 2003
Stored HookflashS-22
FEATURE 
DESCRIPTIONThe Stored Hookflash feature allows any Multiline Terminal user to store a
hookflash in a Speed Dial buffer to allow one-step access to certain Centrex
or PBX features.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals.
Required Components
None.
OPERATING 
PROCEDURES
1. Press T.
2. Press 
Q.
Enter buffer (80~99) followed by trunk access code.
3. Press
S to enter a...

July 2003 NEC Business Solutions Ltd
562 – S22Stored Hookflash
Doc. No. 8201 - Release 1.0
July 2003
1. Press T.
2. Press 
Q.
3. Press the One-Touch key.
4. Dial 
0.
5. Dial the Trunk or Trunk Group Access Code (maximum four digits).
6. Press 
S to enter a hookflash.
7. Dial the desired telephone number.
8. Press
T.
1. Press 
T.
2. Press 
Q.
3. Dial the System Speed Dial buffer number (
00~II or
000~ III).
4. Dial the Trunk or Trunk Group Access Code (maximum four digits).
5. Press 
S to enter a...