NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual S2 – 503
Doc. No. 8201 - Release 1.0
July 2003
	If the Feature key or digit key is not pressed within 10 seconds,
scrolling is cancelled.
	When scrolling, the system uses the following criteria to display the
information in the order listed below:
zSpaces (between alphabetical characters)
zAlphabetical Characters
zDigits
zSpecial Characters
	If more than one entry has the same name, the Speed Dial buffer with
the lowest number...

July 2003 NEC Business Solutions Ltd
504 – S2Scrolling Directories
Doc. No. 8201 - Release 1.0
July 2003
	Scrolling mode is cancelled when one of the following keys
are pressed: Hold, Transfer, Answer, Redial, One-Touch, or
Feature Access. 
	Key operation is ignored when Conf or Recall is pressed during
scrolling.
	A maximum 12 characters are displayed in the Multiline Terminal LCD
if the system is programmed for 1000 System Speed Dial numbers. 
	A maximum 13 characters are displayed in the Multiline...

Features and Specifications Manual S3 – 505
Doc. No. 8201 - Release 1.0
July 2003
Secondary Incoming 
Extension S-3
FEATURE 
DESCRIPTIONSecondary Incoming Extensions can be assigned on Flexible Line keys.
The status of the Secondary Incoming Extension appears on the LED of the
Secondary Incoming Extension that is assigned. An incoming internal,
ringing Tie/DID, DIT/ANA, CO Transfer Ring, or call forwarded call can be
picked up from a Secondary Incoming Extension.
SYSTEM 
AVAILABILITYTerminal Type
All...

July 2003 NEC Business Solutions Ltd
506 – S3Secondary Incoming Extension
Doc. No. 8201 - Release 1.0
July 2003
	Calls cannot be originated from a Secondary Incoming Extension.
	Off-Hook Ringing is provided with calls ringing into Secondary
Incoming Extensions. 
	Secondary Incoming Extensions cannot be set for Call Forward.
	Internal and outside line calls answered from a Secondary Incoming
Extension become the answering station user call.
	Off-Hook indication (BLF) is not provided on the Secondary...

Features and Specifications Manual S4 – 507
Doc. No. 8201 - Release 1.0
July 2003
Seized Trunk Name/
Number DisplayS-4
FEATURE 
DESCRIPTIONThe Seized Trunk Name/Number Display feature displays the telephone
name or number (assigned in System Programming) of each trunk in the
system. These names or numbers appear on the Multiline Terminal LCD
when a trunk is seized.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals with an LCD.
Required Components
None.
OPERATING 
PROCEDURES
1. Press T.
2. Dial...

July 2003 NEC Business Solutions Ltd
508 – S4 Seized Trunk Name/ Number Display
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BCT4Trunk Name/Number Assignment3-00
4When the system is at default this Memory Block must be programmed for the feature to be used. 

Features and Specifications Manual S5 – 509
Doc. No. 8201 - Release 1.0
July 2003
Simplified Call DistributionS-5
FEATURE 
DESCRIPTIONSimplified Call Distribution is a hunting method that distributes calls evenly
to all members of a hunt group. It is very similar to UCD but does not require
members to control call processing status by logging off. Hunting is
instituted when a DIT, DID, TIE or VRS(4)-U(  ) ETU call is terminated at an
SCD group pilot number. Up to 32 SCD members can be divided among
four...

July 2003 NEC Business Solutions Ltd
510 – S5Simplified Call Distribution
Doc. No. 8201 - Release 1.0
July 2003
	If an SCD call is unanswered the Xen IPK system uses the Call
Forward - No Answer timer to send the call to the next available SCD
station. This forward on no answer is a single event and does not
repeat itself for the duration of that SCD call.
	Calls to an SCD group must be transferred to an agent and not
the pilot.
	SCD group can have a hunt on busy set using MB4-14 and MB4-15.
	Call...

Features and Specifications Manual S6 – 511
Doc. No. 8201 - Release 1.0
July 2003
Single Line Telephone 
AccessS-6
FEATURE 
DESCRIPTIONThe Xen IPK system provides for the connection of a maximum of 118
Single Line Telephones (SLTs). Single Line Telephone users can make CO/
PBX calls, internal calls, and paging calls. 
SYSTEM 
AVAILABILITYTerminal Type
Single Line Telephones.
Required Components
OPX(2)-U(  ) ETU
SLI(8)-U(  ) ETU
SLI(4)-U(  ) ETU
SLT(1)-U(  ) ADP connected to a ESIB/ESIE(8)-U(  ) ETU port...

July 2003 NEC Business Solutions Ltd
512 – S6Single Line Telephone Access
Doc. No. 8201 - Release 1.0
July 2003
1. Press the hookswitch momentarily, and receive internal dial tone.
2. Dial the station number where call is to be transferred.
3. Hang up.
1. Lift the handset, and receive internal dial tone.
2. Dial the Feature Access Code.
SERVICE 
CONDITIONSData Assignment
	All Feature Access Codes can be used from a Single Line Telephone if
allowed by Station Class of Service.
	Internal and outside calls...