NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual S6 – 513
Doc. No. 8201 - Release 1.0
July 2003
	After the PBR is released, DTMF tones from a Single Line Telephone
are not detected by the system but are sent directly to the CO/PBX
line.
	If Data Line Security is assigned for a Single Line Telephone, override
tones are denied to this station.
	When a Single Line Telephone is called, no PBR is connected to that
Single Line Telephone. Therefore, no features can be set at that...

July 2003 NEC Business Solutions Ltd
514 – S6Single Line Telephone Access
Doc. No. 8201 - Release 1.0
July 2003
¶+BTIBounce Protect Time Selection 1-3-01
¶+BTTStation Name Assignment 4-18
¶+BTTTelephone to Tenant Assignment 4-09
¶+BTTSLT Data Line Security Assignment 4-90
¶+BTTCO/PBX Ring Assignment (Day Mode) 4-01
¶+BTTCO/PBX Ring Assignment (Night Mode) 4-02
¶+BCTDIT Assignment 3-42
¶+BCTANA Assignment 3-43
4When the system is at default this Memory Block must be programmed for the feature to be used....

Features and Specifications Manual S7 – 515
Doc. No. 8201 - Release 1.0
July 2003
SLT AdapterS-7
FEATURE 
DESCRIPTIONThe Single Line Telephone (SLT) Adapter allows a port of an ESIB/
ESIE(8)-U( ) ETU to support a Single Line Telephone. A Single Line
Telephone can be connected to the ESI port using the SLT Adapter and 2-
wire cable. Seven SLT(1)-U( ) ADP Single Line Telephone Adapters can be
installed in the Xen IPK system.
SYSTEM 
AVAILABILITYTerminal Type
Single Line Telephones.
Required Components...

July 2003 NEC Business Solutions Ltd
516 – S7SLT Adapter
Doc. No. 8201 - Release 1.0
July 2003
1. Press the hookswitch momentarily, and receive second dial tone.
2. Dial the station number where call is to be transferred.
3. Hang up.
1. Lift the handset, and receive internal dial tone.
2. Dial the applicable Feature Access Code.
SERVICE 
CONDITIONSData Assignment
	The station must be specified as an SLT in System Programming. 
Restrictions
	Message Waiting LED is not supported.
	SLT(1)-U(  ) ADPs do not...

Features and Specifications Manual S8 – 517
Doc. No. 8201 - Release 1.0
July 2003
SLT Timed AlarmS-8
FEATURE 
DESCRIPTIONA Timed Alarm (reminder) may be set at any Single Line Telephone. At
programmed intervals, the system automatically calls the SLT station user
to remind the user of a scheduled time.
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
Any Single Line Telephone port.
OPERATING 
PROCEDURES
1. Lift the handset, and receive internal dial tone.
2. Dial the Timed Alarm set...

July 2003 NEC Business Solutions Ltd
518 – S8SLT Timed Alarm
Doc. No. 8201 - Release 1.0
July 2003
1. Lift the handset or press P, and receive internal dial tone.
2. Dial the Timed Alarm set/cancel to Single Line Telephone Access
Code ______ (not assigned at default).
3. Dial the Single Line Telephone station number.
4. Enter time as 
II:II.
5. Restore the handset.
1. Press 
T.
2. Dial 
EH.
3. Press 
T.
SERVICE 
CONDITIONS	Timed Alarm must be set in five-minute increments for Single Line
Telephones using...

Features and Specifications Manual S9 – 519
Doc. No. 8201 - Release 1.0
July 2003
SoftkeysS-9
FEATURE 
DESCRIPTIONThe Xen IPK system provides softkeys on all Dterm Series i display (DTR)
and DTU-Type Multiline Terminals. Currently Speed Dial Scrolling
Directories, Account Code - Forced/Verified and XenMail Digital Voice Mail
systems make extensive use of these keys to guide a station user
effortlessly through difficult to use feature operations.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals...

July 2003 NEC Business Solutions Ltd
520 – S9Softkeys
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual S10 – 521
Doc. No. 8201 - Release 1.0
July 2003
Speed Dial – StationS-10
FEATURE 
DESCRIPTIONWhen 100-memory allocation is specified, each station in the system can be
assigned 20 Station Speed Dial buffers. Each Station Speed Dial buffer may
contain 24 digits or four other buffer numbers (Nesting Dial) and the called
party name. The DTR-32D-1A TEL and DTU-32D-1A TEL have 16 One-
Touch keys that can also be used for Speed Dial. The One-Touch key buffer
may contain a...

July 2003 NEC Business Solutions Ltd
522 – S10Speed Dial – Station
Doc. No. 8201 - Release 1.0
July 2003
1. Press T.
2. Press 
Q.
3. Press the Feature Access key.
4. Dial 
0.
5. Dial the Trunk or Trunk Group Access Code (maximum four digits).
6. Dial the desired telephone number.
7. Press
T.
1. Press 
T. 
2. Press 
Q.
3. Press the One-Touch key.
4. Dial 
0.
5. Dial the Trunk or Trunk Group Access Code (maximum four digits).
6. Dial the desired telephone number.
7. Press 
T.
1. Lift the handset, and...