NEC Xen Ipk Features And Specifications Manual

Features and Specifications Manual P7 – 463
Doc. No. 8201 - Release 1.0
July 2003
Privacy on All CallsP-7
FEATURE 
DESCRIPTIONThe system provides complete Privacy on All Calls. A station user cannot
enter another conversation unless allowed via Barge-In or Add-On
Conference.
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING 
PROCEDURES
SERVICE 
CONDITIONS
Data Assignment
	Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2] Page 1 LK5 to Allow...

July 2003 NEC Business Solutions Ltd
464 – P7Privacy on All Calls
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BTSClass of Service (Station) Feature Selection 2 1-8-08 1-4, 1-5
4When the system is at default this Memory Block must be programmed for the feature to be used. 

Features and Specifications Manual P8 – 465
Doc. No. 8201 - Release 1.0
July 2003
Privacy ReleaseP-8
FEATURE 
DESCRIPTIONPrivacy Release allows the multiline terminal user to release the privacy on
an outside line by pressing a privacy release key programmed on the
station. Another user can then press the same CO/PBX or CAP key to join
the conversation in progress.
SYSTEM 
AVAILABILITYTerminal Type
Multiline Terminals.
Required components
None.
OPERATING 
PROCEDURES
1. Press T.
2. Press 
Q.
3. Press the...

July 2003 NEC Business Solutions Ltd
466 – P8Privacy Release
Doc. No. 8201 - Release 1.0
July 2003
1. Lift the handset or press P.
2. Press the CO/PBX Line key or CAP key that released privacy.
1. Press the flashing line key or dial trunk access code for the trunk.
SERVICE 
CONDITIONSData Assignment
	Use Memory Block 2-05 (Line Key Selection) to assign Tenant-Wide or
Telephone (default) Mode for each Tenant.
	Use Memory Block 2-06 (Line Key Selection for Tenant Mode) to
assign CO/PBX trunks to the...

Xen IPK Features and Specifications Manual
Features and Specifications Manual P8 – 467
Doc. No. 8201 - Release 1.0
July 2003
	Privacy Release is not allowed if a conference is in progress.
	To join a CO/PBX call using Privacy Release the originating CO/PBX
key or CAP key must be assigned to that station.
	When only one station has entered via Privacy Release and feature
deactivated, then the feature cannot be activated again until the joined
station disconnects from conference.
General
	Privacy Release...

July 2003 NEC Business Solutions Ltd
468 – P8Privacy Release
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BNTrunk to Tenant Assignment 2-01
¶+BNLine Key Selection 2-05
¶+BTTTelephone to Tenant Assignment 4-09
¶+BNLine Key Selection for Tenant Mode 2-06
¶+BTMLine Key Selection for Telephone Mode 4-12
One-Touch and Feature Access keys are programmable through SAT...

Features and Specifications Manual P9 – 469
Doc. No. 8201 - Release 1.0
July 2003
Private LinesP-9
FEATURE 
DESCRIPTIONThe Private Lines feature allows two outside lines to be programmed as
private lines. Only a Multiline Terminal that has been programmed for the
Private Lines feature can have access to these private lines. The LED
status indication for the Private Lines does not appear on any other Multiline
Terminal.
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING...

July 2003 NEC Business Solutions Ltd
470 – P9Private Lines
Doc. No. 8201 - Release 1.0
July 2003
	Tie lines can be assigned as Private Lines.
	Private Lines cannot follow Call Forward assignments unless the
destination telephones use the same Private Lines.
RELATED 
FEATURES LIST
GUIDE TO 
FEATURE 
PROGRAMMINGFeature 
NumberFeature Name
B-3 Barge-In
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BAAccess Code (1-, 2-, 3-Digit)...

Features and Specifications Manual P10 – 471
Doc. No. 8201 - Release 1.0
July 2003
Programming from 
Multiline TerminalP-10
FEATURE 
DESCRIPTIONSystem Programming can be performed from designated Multiline
Terminals (with an LCD) connected to the first two ESI(8)-U( ) ETU ports.
Some programming changes can be entered while the system is operating,
other programming changes occur when the affected telephones and
circuits are idle.
SYSTEM 
AVAILABILITYTerminal Type
Multiline Terminals (with LCD).
Required...

July 2003 NEC Business Solutions Ltd
472 – P10 Programming from Multiline Terminal
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK